logo Debian Debian Debian-France Debian-Facile Debian-fr.org Forum-Debian.fr Debian ? Communautés logo inclusivité

Debian-facile

Bienvenue sur Debian-Facile, site d'aide pour les nouveaux utilisateurs de Debian.

Vous n'êtes pas identifié(e).

#1 13-06-2015 16:28:32

Anonyme-13
Invité

Système de fichiers accessible en lecture seulement

Bonjour,
Aujourd'hui nouveau soucis.

Il met impossible de copier/coller et supprimer des fichiers ou dossier sur ma clef USB
le message suivant s’affiche :

Système de fichiers accessible en lecture seulement

Pourtant jusqu’à maintenant tout allait bien avec cette clef.
Un chmod a+rwx ne marche pas non plus.

Avez-vous une solution, et quel commande doit-je vous retourner ?
Je suis sous debian jessie xfce
Linux DebianFlo 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt11-1 (2015-05-24) x86_64 GNU/Linux

Merci d'avance

#2 13-06-2015 16:46:54

smolski
quasi...modo
Lieu : AIN
Distrib. : backports (buster) 10
Noyau : Linux 4.19.0-8-amd64
(G)UI : gnome
Inscription : 21-10-2008

Re : Système de fichiers accessible en lecture seulement

Que renvoit la commande :

ls -l /media/ta_clef


Mettre le nom de ta clef à la place de ta_clef en utilisant l'autocompletion. smile


saque eud dun (patois chtimi : fonce dedans)

Hors ligne

#3 13-06-2015 17:59:21

Anonyme-13
Invité

Re : Système de fichiers accessible en lecture seulement

total 8
drwx------ 13 florian florian 8192 janv.  1  1970 USBFLO
 

Dernière modification par Anonyme-13 (13-06-2015 18:14:58)

#4 13-06-2015 18:16:55

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

Que donne la commande :


grep /media/ /proc/mounts
 



Il faudrait peut être remonter la clef en lecture/écriture. Mais avant, je pense que vérifier
les messages du noyau serait une bonne idée :


dmesg
 

Hors ligne

#5 13-06-2015 20:29:23

Anonyme-13
Invité

Re : Système de fichiers accessible en lecture seulement

grep /media/ /proc/mounts]


/dev/sdb /media/florian/USBFLO vfat ro,nosuid,nodev,relatime,uid=1000,gid=1000,
fmask=0022,dmask=0077,codepage=437,iocharset=utf8,shortname=mixed,showexec,utf8,flush,errors=remount-ro 0 0


.
.
.
.
.

dmsg


Que des :


[  551.869407] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  551.871108] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  551.873053] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  551.874763] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  551.876518] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  551.878224] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  551.879838] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  598.614243] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  598.615928] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  598.617637] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  598.619432] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  598.621142] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  598.622847] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
[  598.623822] FAT-fs (sdb): error, fat_get_cluster: invalid cluster chain (i_pos 524312)
 


Parfois coupé par des :

[  471.948881] fat_get_cluster: 7 callbacks suppressed
 

#6 13-06-2015 21:03:21

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

Le système de fichier a un problème voire ta clef usb. À ta place j'essaierai de sauvegarder tous les fichiers
de la clef, sur ton DD. D'abord en faisant une copie des fichiers :


cp -r /media/florian/USBFLO <rep_sauvegarde>
 


Si cela ne marche pas, essayer ddrescue (du paquet gddrescue) sur le périphérique :


ddrescue /dev/sdb sauvegarde.out sauvegarde.log
 


Pour essayer d'en récupérer un maximum.
Tu pourrais essayer de faire un badblocks en mode lecture pour tester l'état de la clef :


badblocks /dev/sdb -o badblocks.list
 


Après on verra. J'ai l'impression que ta clef est fichue.
Pendant chaque opération tu peux vérifier les messages du noyau :


dmesg |less
 


Fais bien attention aux commandes à exécuter avec les droits root de ne pas te tromper.

Dernière modification par enicar (13-06-2015 21:03:42)

Hors ligne

#7 14-06-2015 08:55:10

Anonyme-13
Invité

Re : Système de fichiers accessible en lecture seulement

J'ai formater ma clef sur Windows en FAT32, et la clef refonctionne.
Au passage, comment puis-je formater ma clef depuis le terminal ?

#8 14-06-2015 09:18:30

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

Il y a au moins deux possibilités :

  • mkdosfs du paquet dosfstools

  • mformat du paquet mtools


Les deux sont bien, mais fonctionnent de façons un peu différentes. mkdosfs est plus proche
du fonctionnement unix ; mformat utilise une syntaxe plus proche des utilitaire dos, mais
demande plus de configuration avant de pouvoir être utilisé (quoique les choses aient évolué).

Hors ligne

#9 14-06-2015 09:26:32

paskal
autobahn
Lieu : ailleurs
Inscription : 14-06-2011
Site Web

Re : Système de fichiers accessible en lecture seulement

Et

mkfs.vfat -F 32 /dev/sdnx

n et x représentant le périphérique usb.


Exemple, en donnant un nom au volume :

mkfs.vfat -F 32 -n CLE_USB_PERSO /dev/sdf1


I'd love to change the world
But I don't know what to do
So I'll leave it up to you...

logo-sur-fond.png

Hors ligne

#10 14-06-2015 09:49:08

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

Tiens, je viens de m'apercevoir que mkfs.vfat et mkdosfs sont des liens vers mkfs.fat du paquet dosfstools wink

Hors ligne

#11 14-06-2015 10:37:12

Anonyme-13
Invité

Re : Système de fichiers accessible en lecture seulement

Suite à un :

fdisk -l


Disque /dev/sdb : 14,9 GiB, 15931539456 octets, 31116288 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0x73696420

Device     Boot      Start        End    Sectors   Size Id Type
/dev/sdb1  ?    1936286752 6221126032 4284839281     2T 45 inconnu
/dev/sdb2  ?    1853169786 3723051230 1869881445 891,6G 65 Novell Netware 386
/dev/sdb3  ?    1701978226 3336544981 1634566756 779,4G 20 inconnu
/dev/sdb4  ?    2885681152 2885734079      52928  25,9M  d inconnu
 



Ma clef n'appariait pas.
Je l'ai monté de cette façon :

mount /dev/sdb /media/florian/

#12 14-06-2015 10:45:51

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

Remarque, que windows ait pu formater ta clef, ne veut pas dire qu'elle est bonne état.
Je ne sais pas ce que fait ou ne fait pas windows. Je t'avais suggérais d'utiliser badblocks,
l'as tu fait ?
Que veux tu dire par :

Gnugnu a écrit :

Ma clef n'apparait pas.


Que dit la commande :


grep /media/ /proc/mounts
 


Et que raconte le noyau :


dmesg |less
 

Hors ligne

#13 14-06-2015 12:17:44

Anonyme-13
Invité

Re : Système de fichiers accessible en lecture seulement

enicar a écrit :

Je t'avais suggérais d'utiliser badblocks,
l'as tu fait ?


badblocks ne me retourne rien

enicar a écrit :

Que veux tu dire par :
Ma clef n'apparait pas.


En allant sur ce site, http://dmesg.fr/gestion-hardware/56-for … -usb-linux
Ils parlaient de ça :

Vous devez d'abord repérer la clé. Tapez :

fdisk -l

et cherchez la ligne qui correspond à votre clé USB de 4 Go.

Exemple :

Disk /dev/sdf: 4023 MB, 4023385600 bytes
124 heads, 62 sectors/track, 1022 cylinders
Units = cylinders of 7688 * 512 = 3936256 bytes
Disk identifier: 0x0004098c

Device Boot      Start         End      Blocks   Id  System
/dev/sdf1 1        1022     3928537   83  Linux



Or moi ma clef ne s'affiche pas :

Device     Boot      Start        End    Sectors   Size Id Type
/dev/sdb1  ?    1936286752 6221126032 4284839281     2T 45 inconnu
/dev/sdb2  ?    1853169786 3723051230 1869881445 891,6G 65 Novell Netware 386
/dev/sdb3  ?    1701978226 3336544981 1634566756 779,4G 20 inconnu
/dev/sdb4  ?    2885681152 2885734079      52928  25,9M  d inconnu



grep /media/ /proc/mounts ne me retourne rien.

pour le dmesg |less :

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.16.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt11-1 (2015-05-24)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.16.0-4-amd64 root=UUID=e6acd7b7-af5b-47d0-a743-53a328329a34 ro quiet
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009cfff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009d000-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000009b63efff] usable
[    0.000000] BIOS-e820: [mem 0x000000009b63f000-0x000000009b6befff] reserved
[    0.000000] BIOS-e820: [mem 0x000000009b6bf000-0x000000009b7befff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000009b7bf000-0x000000009b7fefff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000009b7ff000-0x000000009b7fffff] usable
[    0.000000] BIOS-e820: [mem 0x000000009b800000-0x000000009fffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb03fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed13fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed18000-0x00000000fed19fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1b000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffe80000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000157ffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.6 present.
[    0.000000] DMI: Hewlett-Packard HP Pavilion dv7 Notebook PC/144B, BIOS F.29 11/07/2011
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] AGP: No AGP bridge found
[    0.000000] e820: last_pfn = 0x158000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-EFFFF write-through
[    0.000000]   F0000-FFFFF write-combining
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 0FFE00000 mask FFFE00000 write-protect
[    0.000000]   2 base 080000000 mask FE0000000 write-back
[    0.000000]   3 base 09C000000 mask FFC000000 uncachable
[    0.000000]   4 base 09B800000 mask FFF800000 uncachable
[    0.000000]   5 base 100000000 mask F80000000 write-back
[    0.000000]   6 base 158000000 mask FF8000000 uncachable
[    0.000000]   7 base 160000000 mask FE0000000 uncachable
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: last_pfn = 0x9b800 max_arch_pfn = 0x400000000
[    0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01af4000, 0x01af4fff] PGTABLE
[    0.000000] BRK [0x01af5000, 0x01af5fff] PGTABLE
[    0.000000] BRK [0x01af6000, 0x01af6fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x157e00000-0x157ffffff]
[    0.000000]  [mem 0x157e00000-0x157ffffff] page 2M
[    0.000000] BRK [0x01af7000, 0x01af7fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x154000000-0x157dfffff]
[    0.000000]  [mem 0x154000000-0x157dfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x100000000-0x153ffffff]
[    0.000000]  [mem 0x100000000-0x153ffffff] page 2M
[    0.000000] BRK [0x01af8000, 0x01af8fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x00100000-0x9b63efff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x9b5fffff] page 2M
[    0.000000]  [mem 0x9b600000-0x9b63efff] page 4k
[    0.000000] init_memory_mapping: [mem 0x9b7ff000-0x9b7fffff]
[    0.000000]  [mem 0x9b7ff000-0x9b7fffff] page 4k
[    0.000000] RAMDISK: [mem 0x3620a000-0x370fcfff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000FE020 000024 (v02 HPQOEM)
[    0.000000] ACPI: XSDT 0x000000009B7FE120 00007C (v01 HPQOEM SLIC-MPC 00000001      01000013)
[    0.000000] ACPI: FACP 0x000000009B7FC000 0000F4 (v04 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: DSDT 0x000000009B7E9000 00F50F (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: FACS 0x000000009B75E000 000040
[    0.000000] ACPI: ASF! 0x000000009B7FD000 0000A5 (v32 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: HPET 0x000000009B7FB000 000038 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: APIC 0x000000009B7FA000 00008C (v02 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: MCFG 0x000000009B7F9000 00003C (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: SLIC 0x000000009B7E8000 000176 (v01 HPQOEM SLIC-MPC 00000001 SLIC 000F4240)
[    0.000000] ACPI: BOOT 0x000000009B7E5000 000028 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: ASPT 0x000000009B7E2000 000034 (v04 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: WDAT 0x000000009B7E1000 000224 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: SSDT 0x000000009B7E0000 0009F1 (v01 PmRef  CpuPm    00003000 INTL 20051117)
[    0.000000] ACPI: SSDT 0x000000009B7DE000 001B34 (v01 AmdRef AmdTabl  00001000 INTL 20051117)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x0000000157ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x157ffffff]
[    0.000000]   NODE_DATA [mem 0x157ff8000-0x157ffcfff]
[    0.000000]  [ffffea0000000000-ffffea0004bfffff] PMD -> [ffff880153800000-ffff880156ffffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x157ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009cfff]
[    0.000000]   node   0: [mem 0x00100000-0x9b63efff]
[    0.000000]   node   0: [mem 0x9b7ff000-0x9b7fffff]
[    0.000000]   node   0: [mem 0x100000000-0x157ffffff]
[    0.000000] On node 0 totalpages: 996828
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3996 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 8646 pages used for memmap
[    0.000000]   DMA32 zone: 632384 pages, LIFO batch:31
[    0.000000]   Normal zone: 4928 pages used for memmap
[    0.000000]   Normal zone: 360448 pages, LIFO batch:31
[    0.000000] Reserving Intel graphics stolen memory at 0x9e000000-0x9fffffff
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x05] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x9b63f000-0x9b6befff]
[    0.000000] PM: Registered nosave memory: [mem 0x9b6bf000-0x9b7befff]
[    0.000000] PM: Registered nosave memory: [mem 0x9b7bf000-0x9b7fefff]
[    0.000000] PM: Registered nosave memory: [mem 0x9b800000-0x9fffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xa0000000-0xefffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xf7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfeafffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfeb03fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfeb04000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed0ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed13fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed14000-0xfed17fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed18000-0xfed19fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed1afff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1b000-0xfed1ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffe7ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xffe80000-0xffffffff]
[    0.000000] e820: [mem 0xa0000000-0xefffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff880157c00000 s80896 r8192 d21504 u262144
[    0.000000] pcpu-alloc: s80896 r8192 d21504 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 983177
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.16.0-4-amd64 root=UUID=e6acd7b7-af5b-47d0-a743-53a328329a34 ro quiet
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] AGP: Checking aperture...
[    0.000000] AGP: No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 3836136K/3987312K available (5209K kernel code, 946K rwdata, 1832K rodata, 1204K init, 840K bss, 151176K reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000]  RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=8.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.000000] NR_IRQS:33024 nr_irqs:744 16
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 2527.296 MHz processor
[    0.000030] Calibrating delay loop (skipped), value calculated using timer frequency.. 5054.59 BogoMIPS (lpj=10109184)
[    0.000033] pid_max: default: 32768 minimum: 301
[    0.000041] ACPI: Core revision 20140424
[    0.017700] ACPI: All ACPI Tables successfully acquired
[    0.042838] Security Framework initialized
[    0.042849] AppArmor: AppArmor disabled by boot time parameter
[    0.042850] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.043089] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.044361] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.044941] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.044946] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.045200] Initializing cgroup subsys memory
[    0.045205] Initializing cgroup subsys devices
[    0.045213] Initializing cgroup subsys freezer
[    0.045215] Initializing cgroup subsys net_cls
[    0.045220] Initializing cgroup subsys blkio
[    0.045223] Initializing cgroup subsys perf_event
[    0.045225] Initializing cgroup subsys net_prio
[    0.045252] CPU: Physical Processor ID: 0
[    0.045253] CPU: Processor Core ID: 0
[    0.045258] mce: CPU supports 9 MCE banks
[    0.045268] CPU0: Thermal monitoring enabled (TM1)
[    0.045275] process: using mwait in idle threads
[    0.045279] Last level iTLB entries: 4KB 512, 2MB 7, 4MB 7
Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
tlb_flushall_shift: 6
[    0.045370] Freeing SMP alternatives memory: 20K (ffffffff81a1b000 - ffffffff81a20000)
[    0.046418] ftrace: allocating 21623 entries in 85 pages
[    0.056668] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.096336] smpboot: CPU0: Intel(R) Core(TM) i5 CPU       M 460  @ 2.53GHz (fam: 06, model: 25, stepping: 05)
[    0.203283] Performance Events: PEBS fmt1+, 16-deep LBR, Westmere events, Intel PMU driver.
[    0.203300] perf_event_intel: CPUID marked event: 'bus cycles' unavailable
[    0.203303] ... version:                3
[    0.203303] ... bit width:              48
[    0.203304] ... generic registers:      4
[    0.203305] ... value mask:             0000ffffffffffff
[    0.203306] ... max period:             000000007fffffff
[    0.203307] ... fixed-purpose events:   3
[    0.203307] ... event mask:             000000070000000f
[    0.204780] x86: Booting SMP configuration:
[    0.204782] .... node  #0, CPUs:      #1
[    0.218030] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.218155]  #2 #3
[    0.244600] x86: Booted up 1 node, 4 CPUs
[    0.244604] smpboot: Total of 4 processors activated (20218.36 BogoMIPS)
[    0.246966] devtmpfs: initialized
[    0.250216] PM: Registering ACPI NVS region [mem 0x9b6bf000-0x9b7befff] (1048576 bytes)
[    0.251155] pinctrl core: initialized pinctrl subsystem
[    0.251241] NET: Registered protocol family 16
[    0.251358] cpuidle: using governor ladder
[    0.251360] cpuidle: using governor menu
[    0.251395] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.251397] ACPI: bus type PCI registered
[    0.251398] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.251490] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[    0.251493] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in E820
[    0.251732] PCI: Using configuration type 1 for base access
[    0.263703] ACPI: Added _OSI(Module Device)
[    0.263705] ACPI: Added _OSI(Processor Device)
[    0.263706] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.263707] ACPI: Added _OSI(Processor Aggregator Device)
[    0.279331] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.284983] ACPI: Dynamic OEM Table Load:
[    0.284990] ACPI: SSDT 0xFFFF880152DBB000 000432 (v01 PmRef  Cpu0Ist  00003000 INTL 20051117)
[    0.285488] ACPI: Dynamic OEM Table Load:
[    0.285494] ACPI: SSDT 0xFFFF880152DB4000 000891 (v01 PmRef  Cpu0Cst  00003001 INTL 20051117)
[    0.307530] ACPI: Dynamic OEM Table Load:
[    0.307535] ACPI: SSDT 0xFFFF880152D87000 000303 (v01 PmRef  ApIst    00003000 INTL 20051117)
[    0.316713] ACPI: Dynamic OEM Table Load:
[    0.316718] ACPI: SSDT 0xFFFF880152EA4E00 000119 (v01 PmRef  ApCst    00003000 INTL 20051117)
[    0.353700] ACPI: Interpreter enabled
[    0.353709] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140424/hwxface-580)
[    0.353715] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
[    0.353734] ACPI: (supports S0 S3 S4 S5)
[    0.353735] ACPI: Using IOAPIC for interrupt routing
[    0.353771] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.790846] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e])
[    0.790851] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.790883] \_SB_.PCI0:_OSC invalid UUID
[    0.790884] _OSC request data:1 1f 0
[    0.790887] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[    0.791573] PCI host bridge to bus 0000:00
[    0.791576] pci_bus 0000:00: root bus resource [bus 00-7e]
[    0.791578] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.791579] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.791581] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.791582] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xfeafffff]
[    0.791590] pci 0000:00:00.0: [8086:0044] type 00 class 0x060000
[    0.791607] DMAR: Disabling batched IOTLB flush on Ironlake
[    0.791675] pci 0000:00:01.0: [8086:0045] type 01 class 0x060400
[    0.791707] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.791741] pci 0000:00:01.0: System wakeup disabled by ACPI
[    0.791777] pci 0000:00:02.0: [8086:0046] type 00 class 0x030000
[    0.791787] pci 0000:00:02.0: reg 0x10: [mem 0xc0000000-0xc03fffff 64bit]
[    0.791792] pci 0000:00:02.0: reg 0x18: [mem 0xb0000000-0xbfffffff 64bit pref]
[    0.791796] pci 0000:00:02.0: reg 0x20: [io  0x5050-0x5057]
[    0.791904] pci 0000:00:16.0: [8086:3b64] type 00 class 0x078000
[    0.791932] pci 0000:00:16.0: reg 0x10: [mem 0xc4504000-0xc450400f 64bit]
[    0.792023] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.792115] pci 0000:00:1a.0: [8086:3b3c] type 00 class 0x0c0320
[    0.792533] pci 0000:00:1a.0: reg 0x10: [mem 0xc450a000-0xc450a3ff]
[    0.794981] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.795040] pci 0000:00:1a.0: System wakeup disabled by ACPI
[    0.795090] pci 0000:00:1b.0: [8086:3b56] type 00 class 0x040300
[    0.795113] pci 0000:00:1b.0: reg 0x10: [mem 0xc4500000-0xc4503fff 64bit]
[    0.795218] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.795263] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.795304] pci 0000:00:1c.0: [8086:3b42] type 01 class 0x060400
[    0.795407] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.795451] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.795493] pci 0000:00:1c.1: [8086:3b44] type 01 class 0x060400
[    0.795595] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.795640] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.795694] pci 0000:00:1d.0: [8086:3b34] type 00 class 0x0c0320
[    0.796111] pci 0000:00:1d.0: reg 0x10: [mem 0xc4509000-0xc45093ff]
[    0.798571] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.798628] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.798671] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[    0.798772] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.798812] pci 0000:00:1f.0: [8086:3b09] type 00 class 0x060100
[    0.798987] pci 0000:00:1f.2: [8086:3b29] type 00 class 0x010601
[    0.799015] pci 0000:00:1f.2: reg 0x10: [io  0x5048-0x504f]
[    0.799026] pci 0000:00:1f.2: reg 0x14: [io  0x505c-0x505f]
[    0.799036] pci 0000:00:1f.2: reg 0x18: [io  0x5040-0x5047]
[    0.799046] pci 0000:00:1f.2: reg 0x1c: [io  0x5058-0x505b]
[    0.799056] pci 0000:00:1f.2: reg 0x20: [io  0x5020-0x503f]
[    0.799066] pci 0000:00:1f.2: reg 0x24: [mem 0xc4508000-0xc45087ff]
[    0.799132] pci 0000:00:1f.2: PME# supported from D3hot
[    0.799207] pci 0000:00:1f.3: [8086:3b30] type 00 class 0x0c0500
[    0.799228] pci 0000:00:1f.3: reg 0x10: [mem 0xc4506000-0xc45060ff 64bit]
[    0.799256] pci 0000:00:1f.3: reg 0x20: [io  0x5000-0x501f]
[    0.799353] pci 0000:00:1f.6: [8086:3b32] type 00 class 0x118000
[    0.799380] pci 0000:00:1f.6: reg 0x10: [mem 0xc4507000-0xc4507fff 64bit]
[    0.799576] pci 0000:01:00.0: [1002:68c1] type 00 class 0x030000
[    0.799591] pci 0000:01:00.0: reg 0x10: [mem 0xa0000000-0xafffffff 64bit pref]
[    0.799601] pci 0000:01:00.0: reg 0x18: [mem 0xc4400000-0xc441ffff 64bit]
[    0.799607] pci 0000:01:00.0: reg 0x20: [io  0x4000-0x40ff]
[    0.799618] pci 0000:01:00.0: reg 0x30: [mem 0xfffe0000-0xffffffff pref]
[    0.799658] pci 0000:01:00.0: supports D1 D2
[    0.799710] pci 0000:01:00.1: [1002:aa60] type 00 class 0x040300
[    0.799727] pci 0000:01:00.1: reg 0x10: [mem 0xc4420000-0xc4423fff 64bit]
[    0.799796] pci 0000:01:00.1: supports D1 D2
[    0.799855] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.799857] pci 0000:00:01.0:   bridge window [io  0x4000-0x4fff]
[    0.799860] pci 0000:00:01.0:   bridge window [mem 0xc4400000-0xc44fffff]
[    0.799862] pci 0000:00:01.0:   bridge window [mem 0xa0000000-0xafffffff 64bit pref]
[    0.799972] pci 0000:02:00.0: [1814:3090] type 00 class 0x028000
[    0.800001] pci 0000:02:00.0: reg 0x10: [mem 0xc3400000-0xc340ffff]
[    0.809692] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.809700] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.809707] pci 0000:00:1c.0:   bridge window [mem 0xc3400000-0xc43fffff]
[    0.809717] pci 0000:00:1c.0:   bridge window [mem 0xc0400000-0xc13fffff 64bit pref]
[    0.809824] pci 0000:03:00.0: [10ec:8168] type 00 class 0x020000
[    0.809843] pci 0000:03:00.0: reg 0x10: [io  0x2000-0x20ff]
[    0.809871] pci 0000:03:00.0: reg 0x18: [mem 0xc1404000-0xc1404fff 64bit pref]
[    0.809887] pci 0000:03:00.0: reg 0x20: [mem 0xc1400000-0xc1403fff 64bit pref]
[    0.809899] pci 0000:03:00.0: reg 0x30: [mem 0xffff0000-0xffffffff pref]
[    0.809978] pci 0000:03:00.0: supports D1 D2
[    0.809979] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.810022] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.817668] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.817676] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.817683] pci 0000:00:1c.1:   bridge window [mem 0xc2400000-0xc33fffff]
[    0.817692] pci 0000:00:1c.1:   bridge window [mem 0xc1400000-0xc23fffff 64bit pref]
[    0.817808] pci 0000:00:1e.0: PCI bridge to [bus 04] (subtractive decode)
[    0.817820] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.817822] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.817823] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.817825] pci 0000:00:1e.0:   bridge window [mem 0xa0000000-0xfeafffff] (subtractive decode)
[    0.818351] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.818399] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.818445] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.818492] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.818538] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.818586] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.818632] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.818678] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    1.021919] ACPI: PCI Root Bridge [CPBG] (domain 0000 [bus 7f])
[    1.021923] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    1.021926] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    1.021998] PCI host bridge to bus 0000:7f
[    1.022000] pci_bus 0000:7f: root bus resource [bus 7f]
[    1.022005] pci 0000:7f:00.0: [8086:2c62] type 00 class 0x060000
[    1.022048] pci 0000:7f:00.1: [8086:2d01] type 00 class 0x060000
[    1.022093] pci 0000:7f:02.0: [8086:2d10] type 00 class 0x060000
[    1.022134] pci 0000:7f:02.1: [8086:2d11] type 00 class 0x060000
[    1.022174] pci 0000:7f:02.2: [8086:2d12] type 00 class 0x060000
[    1.022214] pci 0000:7f:02.3: [8086:2d13] type 00 class 0x060000
[    1.022320] ACPI: Enabled 7 GPEs in block 00 to 3F
[    1.022361] ACPI : EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[    1.022472] vgaarb: setting as boot device: PCI:0000:00:02.0
[    1.022474] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    1.022478] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none
[    1.022480] vgaarb: loaded
[    1.022481] vgaarb: bridge control possible 0000:01:00.0
[    1.022482] vgaarb: no bridge control possible 0000:00:02.0
[    1.022540] PCI: Using ACPI for IRQ routing
[    1.027297] PCI: pci_cache_line_size set to 64 bytes
[    1.027386] e820: reserve RAM buffer [mem 0x0009d000-0x0009ffff]
[    1.027387] e820: reserve RAM buffer [mem 0x9b63f000-0x9bffffff]
[    1.027389] e820: reserve RAM buffer [mem 0x9b800000-0x9bffffff]
[    1.027533] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    1.027538] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    1.029568] Switched to clocksource hpet
[    1.034733] pnp: PnP ACPI init
[    1.034747] ACPI: bus type PNP registered
[    1.035006] system 00:00: [io  0x0680-0x069f] has been reserved
[    1.035008] system 00:00: [io  0x0800-0x080f] has been reserved
[    1.035010] system 00:00: [io  0xffff] has been reserved
[    1.035012] system 00:00: [io  0xffff] has been reserved
[    1.035014] system 00:00: [io  0x0400-0x047f] could not be reserved
[    1.035016] system 00:00: [io  0x0500-0x057f] has been reserved
[    1.035017] system 00:00: [io  0x164e-0x164f] has been reserved
[    1.035019] system 00:00: [io  0x0380-0x038e] has been reserved
[    1.035022] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.035060] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[    1.035097] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 (active)
[    1.035138] pnp 00:03: Plug and Play ACPI device, IDs SYN1e1d SYN1e00 SYN0002 PNP0f13 (active)
[    1.035433] system 00:04: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    1.035435] system 00:04: [mem 0xfed10000-0xfed13fff] has been reserved
[    1.035437] system 00:04: [mem 0xfed18000-0xfed18fff] has been reserved
[    1.035439] system 00:04: [mem 0xfed19000-0xfed19fff] has been reserved
[    1.035440] system 00:04: [mem 0xf0000000-0xf1ffffff] has been reserved
[    1.035442] system 00:04: [mem 0xfed20000-0xfed3ffff] has been reserved
[    1.035444] system 00:04: [mem 0xff000000-0xffffffff] could not be reserved
[    1.035446] system 00:04: [mem 0xfee00000-0xfeefffff] could not be reserved
[    1.035447] system 00:04: [mem 0xc4600000-0xc4600fff] has been reserved
[    1.035450] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.237871] pnp: PnP ACPI: found 5 devices
[    1.237874] ACPI: bus type PNP unregistered
[    1.244532] pci 0000:01:00.0: can't claim BAR 6 [mem 0xfffe0000-0xffffffff pref]: no compatible bridge window
[    1.244535] pci 0000:03:00.0: can't claim BAR 6 [mem 0xffff0000-0xffffffff pref]: no compatible bridge window
[    1.244572] pci 0000:01:00.0: BAR 6: assigned [mem 0xc4440000-0xc445ffff pref]
[    1.244575] pci 0000:00:01.0: PCI bridge to [bus 01]
[    1.244577] pci 0000:00:01.0:   bridge window [io  0x4000-0x4fff]
[    1.244580] pci 0000:00:01.0:   bridge window [mem 0xc4400000-0xc44fffff]
[    1.244582] pci 0000:00:01.0:   bridge window [mem 0xa0000000-0xafffffff 64bit pref]
[    1.244586] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    1.244589] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    1.244595] pci 0000:00:1c.0:   bridge window [mem 0xc3400000-0xc43fffff]
[    1.244599] pci 0000:00:1c.0:   bridge window [mem 0xc0400000-0xc13fffff 64bit pref]
[    1.244606] pci 0000:03:00.0: BAR 6: assigned [mem 0xc2400000-0xc240ffff pref]
[    1.244607] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    1.244610] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    1.244616] pci 0000:00:1c.1:   bridge window [mem 0xc2400000-0xc33fffff]
[    1.244620] pci 0000:00:1c.1:   bridge window [mem 0xc1400000-0xc23fffff 64bit pref]
[    1.244627] pci 0000:00:1e.0: PCI bridge to [bus 04]
[    1.244641] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    1.244643] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    1.244644] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    1.244646] pci_bus 0000:00: resource 7 [mem 0xa0000000-0xfeafffff]
[    1.244647] pci_bus 0000:01: resource 0 [io  0x4000-0x4fff]
[    1.244649] pci_bus 0000:01: resource 1 [mem 0xc4400000-0xc44fffff]
[    1.244650] pci_bus 0000:01: resource 2 [mem 0xa0000000-0xafffffff 64bit pref]
[    1.244652] pci_bus 0000:02: resource 0 [io  0x3000-0x3fff]
[    1.244653] pci_bus 0000:02: resource 1 [mem 0xc3400000-0xc43fffff]
[    1.244655] pci_bus 0000:02: resource 2 [mem 0xc0400000-0xc13fffff 64bit pref]
[    1.244656] pci_bus 0000:03: resource 0 [io  0x2000-0x2fff]
[    1.244658] pci_bus 0000:03: resource 1 [mem 0xc2400000-0xc33fffff]
[    1.244659] pci_bus 0000:03: resource 2 [mem 0xc1400000-0xc23fffff 64bit pref]
[    1.244661] pci_bus 0000:04: resource 4 [io  0x0000-0x0cf7]
[    1.244663] pci_bus 0000:04: resource 5 [io  0x0d00-0xffff]
[    1.244664] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[    1.244666] pci_bus 0000:04: resource 7 [mem 0xa0000000-0xfeafffff]
[    1.244739] NET: Registered protocol family 2
[    1.245015] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    1.245120] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    1.245263] TCP: Hash tables configured (established 32768 bind 32768)
[    1.245293] TCP: reno registered
[    1.245298] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    1.245318] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    1.245407] NET: Registered protocol family 1
[    1.245425] pci 0000:00:02.0: Video device with shadowed ROM
[    1.277639] PCI: CLS 64 bytes, default 64
[    1.277689] Unpacking initramfs...
[    1.542561] Freeing initrd memory: 15308K (ffff88003620a000 - ffff8800370fd000)
[    1.542614] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.542616] software IO TLB [mem 0x9763f000-0x9b63f000] (64MB) mapped at [ffff88009763f000-ffff88009b63efff]
[    1.542661] Simple Boot Flag at 0x44 set to 0x1
[    1.542897] microcode: CPU0 sig=0x20655, pf=0x10, revision=0x2
[    1.542904] microcode: CPU1 sig=0x20655, pf=0x10, revision=0x2
[    1.542913] microcode: CPU2 sig=0x20655, pf=0x10, revision=0x2
[    1.542920] microcode: CPU3 sig=0x20655, pf=0x10, revision=0x2
[    1.542992] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.543317] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    1.543383] audit: initializing netlink subsys (disabled)
[    1.543406] audit: type=2000 audit(1434263610.416:1): initialized
[    1.543718] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.543738] zbud: loaded
[    1.543957] VFS: Disk quotas dquot_6.5.2
[    1.543978] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.544040] msgmni has been set to 7522
[    1.544438] alg: No test for stdrng (krng)
[    1.544468] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.544533] io scheduler noop registered
[    1.544535] io scheduler deadline registered
[    1.544573] io scheduler cfq registered (default)
[    1.544792] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    1.545083] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.545100] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.545117] intel_idle: MWAIT substates: 0x1120
[    1.545119] intel_idle: v0.4 model 0x25
[    1.545120] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.545321] GHES: HEST is not enabled!
[    1.545427] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.545932] Linux agpgart interface v0.103
[    1.545987] agpgart-intel 0000:00:00.0: Intel HD Graphics Chipset
[    1.546006] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[    1.546544] agpgart-intel 0000:00:00.0: detected 32768K stolen memory
[    1.546724] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xb0000000
[    1.546853] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.568133] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.568140] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.568279] mousedev: PS/2 mouse device common for all mice
[    1.570821] rtc_cmos 00:01: RTC can wake from S4
[    1.571036] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[    1.571072] rtc_cmos 00:01: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    1.571090] ledtrig-cpu: registered to indicate activity on CPUs
[    1.571261] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[    1.571262] AMD IOMMUv2 functionality not available on this system
[    1.571350] TCP: cubic registered
[    1.571453] NET: Registered protocol family 10
[    1.571705] mip6: Mobile IPv6
[    1.571715] NET: Registered protocol family 17
[    1.571720] mpls_gso: MPLS GSO support
[    1.572059] registered taskstats version 1
[    1.572644] rtc_cmos 00:01: setting system clock to 2015-06-14 06:33:30 UTC (1434263610)
[    1.572713] PM: Hibernation image not present or could not be loaded.
[    1.573476] Freeing unused kernel memory: 1204K (ffffffff818ee000 - ffffffff81a1b000)
[    1.573479] Write protecting the kernel read-only data: 8192k
[    1.575363] Freeing unused kernel memory: 924K (ffff880001519000 - ffff880001600000)
[    1.575826] Freeing unused kernel memory: 216K (ffff8800017ca000 - ffff880001800000)
[    1.586595] systemd-udevd[72]: starting version 215
[    1.586856] random: systemd-udevd urandom read with 9 bits of entropy available
[    1.596799] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.600824] [Firmware Bug]: Invalid critical threshold (0)
[    1.600853] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.600863] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[    1.601519] ACPI: bus type USB registered
[    1.601546] usbcore: registered new interface driver usbfs
[    1.601556] usbcore: registered new interface driver hub
[    1.601864] usbcore: registered new device driver usb
[    1.602001] SCSI subsystem initialized
[    1.602102] r8169 0000:03:00.0: irq 41 for MSI/MSI-X
[    1.602372] r8169 0000:03:00.0 eth0: RTL8168d/8111d at 0xffffc90000664000, 64:31:50:59:29:f7, XID 083000c0 IRQ 41
[    1.602378] r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    1.602406] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.602761] ehci-pci: EHCI PCI platform driver
[    1.602922] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    1.602931] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    1.602949] ehci-pci 0000:00:1a.0: debug port 2
[    1.606924] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    1.606954] ehci-pci 0000:00:1a.0: irq 16, io mem 0xc450a000
[    1.607630] libata version 3.00 loaded.
[    1.608167] thermal LNXTHERM:00: registered as thermal_zone0
[    1.608169] ACPI: Thermal Zone [TZ01] (44 C)
[    1.617392] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    1.617442] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.617444] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.617446] usb usb1: Product: EHCI Host Controller
[    1.617447] usb usb1: Manufacturer: Linux 3.16.0-4-amd64 ehci_hcd
[    1.617449] usb usb1: SerialNumber: 0000:00:1a.0
[    1.617781] hub 1-0:1.0: USB hub found
[    1.617867] hub 1-0:1.0: 3 ports detected
[    1.618395] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    1.618402] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.618417] ehci-pci 0000:00:1d.0: debug port 2
[    1.622356] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    1.622380] ehci-pci 0000:00:1d.0: irq 21, io mem 0xc4509000
[    1.633342] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    1.633398] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.633400] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.633402] usb usb2: Product: EHCI Host Controller
[    1.633403] usb usb2: Manufacturer: Linux 3.16.0-4-amd64 ehci_hcd
[    1.633404] usb usb2: SerialNumber: 0000:00:1d.0
[    1.633539] hub 2-0:1.0: USB hub found
[    1.633545] hub 2-0:1.0: 3 ports detected
[    1.633680] ahci 0000:00:1f.2: version 3.0
[    1.633865] ahci 0000:00:1f.2: irq 42 for MSI/MSI-X
[    1.633964] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 3 Gbps 0x23 impl SATA mode
[    1.633968] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems sxs apst
[    1.650165] scsi0 : ahci
[    1.650454] scsi1 : ahci
[    1.650615] scsi2 : ahci
[    1.650778] scsi3 : ahci
[    1.650930] scsi4 : ahci
[    1.651069] scsi5 : ahci
[    1.651115] ata1: SATA max UDMA/133 abar m2048@0xc4508000 port 0xc4508100 irq 42
[    1.651119] ata2: SATA max UDMA/133 abar m2048@0xc4508000 port 0xc4508180 irq 42
[    1.651120] ata3: DUMMY
[    1.651121] ata4: DUMMY
[    1.651122] ata5: DUMMY
[    1.651125] ata6: SATA max UDMA/133 abar m2048@0xc4508000 port 0xc4508380 irq 42
[    1.929338] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.969280] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.969319] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.969351] ata6: SATA link down (SStatus 0 SControl 300)
[    1.969790] ata1.00: ATA-8: TOSHIBA MK1059GSM, GL002C, max UDMA/100
[    1.969795] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.970375] ata1.00: configured for UDMA/100
[    1.970758] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK1059GS 2C   PQ: 0 ANSI: 5
[    1.971812] ata2.00: ATAPI: hp      DVDRAM GT30L, mP04, max UDMA/100
[    1.974670] ata2.00: configured for UDMA/100
[    1.976421] scsi 1:0:0:0: CD-ROM            hp       DVDRAM GT30L     mP04 PQ: 0 ANSI: 5
[    1.991386] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.991390] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.991570] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.992095] scsi 0:0:0:0: Attached scsi generic sg0 type 0
[    1.992145] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.998522] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    1.998524] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.998638] sd 0:0:0:0: [sda] Write Protect is off
[    1.998640] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.998675] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.061893] usb 1-1: New USB device found, idVendor=8087, idProduct=0020
[    2.061899] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.062601] hub 1-1:1.0: USB hub found
[    2.062693] hub 1-1:1.0: 6 ports detected
[    2.090864]  sda: sda1 sda2 < sda5 >
[    2.091607] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.173232] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    2.305517] usb 2-1: New USB device found, idVendor=8087, idProduct=0020
[    2.305522] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.305928] hub 2-1:1.0: USB hub found
[    2.306141] hub 2-1:1.0: 8 ports detected
[    2.540977] tsc: Refined TSC clocksource calibration: 2527.285 MHz
[    2.577205] usb 2-1.3: new full-speed USB device number 3 using ehci-pci
[    2.597042] PM: Starting manual resume from disk
[    2.597048] PM: Hibernation image partition 8:5 present
[    2.597049] PM: Looking for hibernation image.
[    2.624150] PM: Image not found (code -22)
[    2.624153] PM: Hibernation image not present or could not be loaded.
[    2.670841] usb 2-1.3: New USB device found, idVendor=138a, idProduct=0005
[    2.670848] usb 2-1.3: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[    2.670852] usb 2-1.3: SerialNumber: 0030ce319f85
[    2.741151] usb 2-1.5: new high-speed USB device number 4 using ehci-pci
[    2.855208] usb 2-1.5: New USB device found, idVendor=0408, idProduct=03b2
[    2.855213] usb 2-1.5: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[    2.855217] usb 2-1.5: Product: HP Webcam
[    2.855219] usb 2-1.5: Manufacturer: QCM
[    3.002841] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    3.056952] usb 2-1.1: new low-speed USB device number 5 using ehci-pci
[    3.154503] usb 2-1.1: New USB device found, idVendor=046d, idProduct=c062
[    3.154510] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.154513] usb 2-1.1: Product: USB Laser Mouse
[    3.154517] usb 2-1.1: Manufacturer: Logitech
[    3.156907] hidraw: raw HID events driver (C) Jiri Kosina
[    3.161555] usbcore: registered new interface driver usbhid
[    3.161557] usbhid: USB HID core driver
[    3.162132] input: Logitech USB Laser Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/0003:046D:C062.0001/input/input2
[    3.162239] hid-generic 0003:046D:C062.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB Laser Mouse] on usb-0000:00:1d.0-1.1/input0
[    3.540908] Switched to clocksource tsc
[    3.710263] random: nonblocking pool is initialized
[    6.923231] lp: driver loaded but no devices found
[    6.940014] ppdev: user-space parallel port driver
[    7.336411] fuse init (API version 7.23)
[    7.625862] systemd-udevd[196]: starting version 215
[    9.584706] hp_accel: hardware type DV7 found
[    9.585345] lis3lv02d: 8 bits sensor found
[    9.625861] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input3
[    9.638284] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    9.759313] ACPI: AC Adapter [ACAD] (on-line)
[    9.768246] intel ips 0000:00:1f.6: CPU TDP doesn't match expected value (found 25, expected 29)
[    9.768368] intel ips 0000:00:1f.6: failed to get i915 symbols, graphics turbo disabled until i915 loads
[    9.768471] intel ips 0000:00:1f.6: IPS driver initialized, MCP temp limit 90
[    9.809909] mei_me 0000:00:16.0: irq 43 for MSI/MSI-X
[    9.822753] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042f conflicts with OpRegion 0x0000000000000400-0x000000000000047f (\PMIO) (20140424/utaddress-258)
[    9.822759] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    9.822762] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054f conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20140424/utaddress-258)
[    9.822765] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054f conflicts with OpRegion 0x0000000000000500-0x000000000000054f (\SGGP) (20140424/utaddress-258)
[    9.822768] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054f conflicts with OpRegion 0x0000000000000500-0x000000000000055f (\_SB_.PCI0.P0P3.PEGP.GPIO) (20140424/utaddress-258)
[    9.822771] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    9.822772] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053f conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20140424/utaddress-258)
[    9.822774] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053f conflicts with OpRegion 0x0000000000000500-0x000000000000054f (\SGGP) (20140424/utaddress-258)
[    9.822776] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053f conflicts with OpRegion 0x0000000000000500-0x000000000000055f (\_SB_.PCI0.P0P3.PEGP.GPIO) (20140424/utaddress-258)
[    9.822779] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    9.822780] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20140424/utaddress-258)
[    9.822782] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x000000000000054f (\SGGP) (20140424/utaddress-258)
[    9.822784] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x000000000000055f (\_SB_.PCI0.P0P3.PEGP.GPIO) (20140424/utaddress-258)
[    9.822787] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    9.822788] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   10.020656] ACPI: Battery Slot [BAT0] (battery present)
[   10.020749] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
[   10.020755] ACPI: Power Button [PWRB]
[   10.020802] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input5
[   10.021085] ACPI: Lid Switch [LID0]
[   10.021154] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[   10.021157] ACPI: Power Button [PWRF]
[   10.021380] wmi: Mapper loaded
[   10.235449] input: PC Speaker as /devices/platform/pcspkr/input/input7
[   10.247464] ACPI Warning: SystemIO range 0x0000000000005000-0x000000000000501f conflicts with OpRegion 0x0000000000005000-0x000000000000500f (\_SB_.PCI0.SBUS.SMBI) (20140424/utaddress-258)
[   10.247470] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   10.285188] [drm] Initialized drm 1.1.0 20060810
[   10.546268] [drm] radeon kernel modesetting enabled.
[   10.546290] VGA switcheroo: detected switching method \_SB_.PCI0.GFX0.ATPX handle
[   10.596821] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[   10.636969] radeon 0000:01:00.0: enabling device (0000 -> 0003)
[   10.637238] [drm] initializing kernel modesetting (REDWOOD 0x1002:0x68C1 0x103C:0x144B).
[   10.637252] [drm] register mmio base: 0xC4400000
[   10.637253] [drm] register mmio size: 131072
[   10.719410] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   10.852565] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround
[   10.863509] cfg80211: Calling CRDA to update world regulatory domain
[   11.014812] sound hdaudioC0D0: autoconfig: line_outs=1 (0xd/0x0/0x0/0x0/0x0) type:speaker
[   11.014816] sound hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   11.014817] sound hdaudioC0D0:    hp_outs=1 (0xb/0x0/0x0/0x0/0x0)
[   11.014819] sound hdaudioC0D0:    mono: mono_out=0x0
[   11.014820] sound hdaudioC0D0:    inputs:
[   11.014822] sound hdaudioC0D0:      Internal Mic=0x11
[   11.014824] sound hdaudioC0D0:      Mic=0xa
[   11.050246] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/hdaudioC0D0/input9
[   11.050404] input: HDA Intel MID Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   11.050457] input: HDA Intel MID Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   11.086713] iTCO_vendor_support: vendor-support=0
[   11.087055] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[   11.087089] iTCO_wdt: Found a HM55 TCO device (Version=2, TCOBASE=0x0460)
[   11.087182] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   11.167830] systemd-journald[185]: Received request to flush runtime journal from PID 1
[   11.476217] psmouse serio1: synaptics: queried max coordinates: x [..5672], y [..4550]
[   11.618821] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04773/0xe40000/0x5a0400, board id: 0, fw id: 631163
[   11.686435] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3090, rev 3213 detected
[   11.690234] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[   11.709921] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
[   11.724423] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   11.992034] Adding 7973884k swap on /dev/sda5.  Priority:-1 extents:1 across:7973884k FS
[   12.676758] media: Linux media interface: v0.10
[   12.725424] Linux video capture interface: v2.00
[   12.815165] uvcvideo: Found UVC 1.00 device HP Webcam (0408:03b2)
[   12.823054] input: HP Webcam as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.0/input/input13
[   12.823156] usbcore: registered new interface driver uvcvideo
[   12.823159] USB Video Class driver (1.1.1)
[   12.864289] cfg80211: World regulatory domain updated:
[   12.864292] cfg80211:  DFS Master region: unset
[   12.864293] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   12.864296] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.864297] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.864299] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   12.864300] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   12.864302] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   12.864304] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   12.864305] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   12.864306] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   13.028106] input: HP WMI hotkeys as /devices/virtual/input/input12
[   13.670537] ATOM BIOS: MADISON
[   13.670695] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[   13.670702] radeon 0000:01:00.0: GTT: 1024M 0x0000000040000000 - 0x000000007FFFFFFF
[   13.670707] [drm] Detected VRAM RAM=1024M, BAR=256M
[   13.670710] [drm] RAM width 128bits DDR
[   13.670859] [TTM] Zone  kernel: Available graphics memory: 1926904 kiB
[   13.670863] [TTM] Initializing pool allocator
[   13.670875] [TTM] Initializing DMA pool allocator
[   13.670917] [drm] radeon: 1024M of VRAM memory ready
[   13.670921] [drm] radeon: 1024M of GTT memory ready.
[   13.670954] [drm] Loading REDWOOD Microcode
[   13.714657] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/REDWOOD_pfp.bin
[   13.723708] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/REDWOOD_me.bin
[   13.739062] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/REDWOOD_rlc.bin
[   13.739556] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/REDWOOD_smc.bin
[   13.739567] [drm] Internal thermal controller without fan control
[   13.746860] [drm] radeon: dpm initialized
[   13.839148] RPC: Registered named UNIX socket transport module.
[   13.839155] RPC: Registered udp transport module.
[   13.839158] RPC: Registered tcp transport module.
[   13.839161] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   13.880604] FS-Cache: Loaded
[   13.893549] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/CYPRESS_uvd.bin
[   13.893589] [drm] GART: num cpu pages 262144, num gpu pages 262144
[   13.897423] [drm] PCIE GART of 1024M enabled (table at 0x000000000025D000).
[   13.897578] radeon 0000:01:00.0: WB enabled
[   13.897581] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff88015214fc00
[   13.897583] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff88015214fc0c
[   13.898985] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x000000000005c418 and cpu addr 0xffffc90008e9c418
[   13.898988] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   13.898989] [drm] Driver supports precise vblank timestamp query.
[   13.898991] radeon 0000:01:00.0: radeon: MSI limited to 32-bit
[   13.899018] radeon 0000:01:00.0: irq 45 for MSI/MSI-X
[   13.899033] radeon 0000:01:00.0: radeon: using MSI.
[   13.899070] [drm] radeon: irq initialized.
[   13.916040] [drm] ring test on 0 succeeded in 3 usecs
[   13.916054] [drm] ring test on 3 succeeded in 7 usecs
[   13.935461] FS-Cache: Netfs 'nfs' registered for caching
[   14.004270] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   14.102239] [drm] ring test on 5 succeeded in 2 usecs
[   14.102252] [drm] UVD initialized successfully.
[   14.102570] [drm] ib test on ring 0 succeeded in 0 usecs
[   14.102633] [drm] ib test on ring 3 succeeded in 0 usecs
[   14.254229] [drm] ib test on ring 5 succeeded
[   14.311863] [drm] radeon atom DIG backlight initialized
[   14.311871] [drm] Radeon Display Connectors
[   14.311873] [drm] Connector 0:
[   14.311876] [drm]   LVDS-1
[   14.311879] [drm]   DDC: 0x6560 0x6560 0x6564 0x6564 0x6568 0x6568 0x656c 0x656c
[   14.311881] [drm]   Encoders:
[   14.311883] [drm]     LCD1: INTERNAL_UNIPHY
[   14.311885] [drm] Connector 1:
[   14.311887] [drm]   HDMI-A-1
[   14.311889] [drm]   HPD1
[   14.311892] [drm]   DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[   14.311894] [drm]   Encoders:
[   14.311895] [drm]     DFP1: INTERNAL_UNIPHY1
[   14.311897] [drm] Connector 2:
[   14.311899] [drm]   VGA-1
[   14.311902] [drm]   DDC: 0x64d8 0x64d8 0x64dc 0x64dc 0x64e0 0x64e0 0x64e4 0x64e4
[   14.311903] [drm]   Encoders:
[   14.311906] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[   14.811952] radeon 0000:01:00.0: No connectors reported connected with modes
[   14.811958] [drm] Cannot find any crtc or sizes - going 1024x768
[   14.813968] [drm] fb mappable at 0xA045E000
[   14.813968] [drm] vram apper at 0xA0000000
[   14.813969] [drm] size 3145728
[   14.813970] [drm] fb depth is 24
[   14.813971] [drm]    pitch is 4096
[   15.837472] vboxdrv: Found 4 processor cores.
[   15.837696] vboxdrv: fAsync=0 offMin=0x130 offMax=0xde7
[   15.837782] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   15.837783] vboxdrv: Successfully loaded version 4.3.18_Debian (interface 0x001a0008).
[   16.789361] vboxpci: IOMMU not found (not registered)
[   16.830287] Console: switching to colour frame buffer device 128x48
[   16.832373] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[   16.832375] radeon 0000:01:00.0: registered panic notifier
[   16.908307] [drm] Initialized radeon 2.39.0 20080528 for 0000:01:00.0 on minor 0
[   16.908614] snd_hda_intel 0000:01:00.1: Handle VGA-switcheroo audio client
[   16.908654] [drm] Memory usable by graphics device = 2048M
[   16.908657] [drm] Replacing VGA console driver
[   16.908963] snd_hda_intel 0000:01:00.1: irq 46 for MSI/MSI-X
[   16.934749] i915 0000:00:02.0: irq 47 for MSI/MSI-X
[   16.934776] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   16.934779] [drm] Driver supports precise vblank timestamp query.
[   16.934890] vga_switcheroo: enabled
[   16.934918] ATPX version 1, functions 0x0000002f
[   16.935072] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=none
[   16.935075] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=none:owns=none
[   16.977307] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[   16.981282] fbcon: inteldrmfb (fb1) is primary device
[   16.981282] fbcon: Remapping primary device, fb1, to tty 1-63
[   17.971776] i915 0000:00:02.0: fb1: inteldrmfb frame buffer device
[   17.972907] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   17.977453] acpi device:01: registered as cooling_device5
[   17.977541] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input15
[   17.977823] ACPI: Video Device [VGA1] (multi-head: yes  rom: no  post: no)
[   17.985857] acpi device:13: registered as cooling_device6
[   17.990313] acpi device:14: registered as cooling_device7
[   17.990423] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:10/LNXVIDEO:02/input/input16
[   17.990620] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 1
[   19.961417] intel ips 0000:00:1f.6: i915 driver attached, reenabling gpu turbo
[   21.924508] snd_hda_intel 0000:01:00.1: Disabling via VGA-switcheroo
[   23.220370] r8169 0000:03:00.0: firmware: direct-loading firmware rtl_nic/rtl8168d-2.fw
[   23.277204] r8169 0000:03:00.0 eth0: link down
[   23.277251] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   26.396565] [drm] PCIE GART of 1024M enabled (table at 0x000000000025D000).
[   26.396699] radeon 0000:01:00.0: WB enabled
[   26.396702] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff88015214fc00
[   26.396704] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff88015214fc0c
[   26.398106] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x000000000005c418 and cpu addr 0xffffc90008e9c418
[   26.414648] [drm] ring test on 0 succeeded in 2 usecs
[   26.414662] [drm] ring test on 3 succeeded in 4 usecs
[   26.600434] [drm] ring test on 5 succeeded in 2 usecs
[   26.600451] [drm] UVD initialized successfully.
[   26.600532] [drm] ib test on ring 0 succeeded in 0 usecs
[   26.600599] [drm] ib test on ring 3 succeeded in 0 usecs
[   26.751816] [drm] ib test on ring 5 succeeded
[   26.863722] snd_hda_intel 0000:01:00.1: Enabling via VGA-switcheroo
[   26.863845] snd_hda_intel 0000:01:00.1: irq 46 for MSI/MSI-X
[   41.931692] snd_hda_intel 0000:01:00.1: Disabling via VGA-switcheroo
[   64.903384] r8169 0000:03:00.0 eth0: link up
[   64.903398] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  955.938473] usb 1-1.2: new high-speed USB device number 3 using ehci-pci
[  956.033288] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=0109
[  956.033296] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  956.033300] usb 1-1.2: Product: USB2.0-CRW
[  956.033303] usb 1-1.2: Manufacturer: Generic
[  956.033306] usb 1-1.2: SerialNumber: 20090815198100000
[  956.187370] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[  956.187467] scsi6 : usb-storage 1-1.2:1.0
[  956.187549] usbcore: registered new interface driver usb-storage
[  957.187137] scsi 6:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[  957.187631] sd 6:0:0:0: Attached scsi generic sg2 type 0
[  957.843045] sd 6:0:0:0: [sdb] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[  957.844078] sd 6:0:0:0: [sdb] Write Protect is off
[  957.844083] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00
[  957.845276] sd 6:0:0:0: [sdb] No Caching mode page found
[  957.845283] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  957.850345]  sdb:
[  957.853953] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 1001.416316] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 1121.049160] perf interrupt took too long (2520 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
[ 1232.864176] usb 1-1.2: USB disconnect, device number 3
[ 1253.487633] usb 1-1.2: new high-speed USB device number 4 using ehci-pci
[ 1253.582610] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=0109
[ 1253.582618] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1253.582622] usb 1-1.2: Product: USB2.0-CRW
[ 1253.582625] usb 1-1.2: Manufacturer: Generic
[ 1253.582628] usb 1-1.2: SerialNumber: 20090815198100000
[ 1253.593735] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 1253.593894] scsi7 : usb-storage 1-1.2:1.0
[ 1254.592382] scsi 7:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[ 1254.592906] sd 7:0:0:0: Attached scsi generic sg2 type 0
[ 1255.248537] sd 7:0:0:0: [sdb] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[ 1255.249627] sd 7:0:0:0: [sdb] Write Protect is off
[ 1255.249633] sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 1255.250684] sd 7:0:0:0: [sdb] No Caching mode page found
[ 1255.250692] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 1255.256598]  sdb:
[ 1255.260370] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 1279.124800] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 1560.158055] usb 1-1.2: USB disconnect, device number 4
[ 2325.000422] CPU3: Core temperature above threshold, cpu clock throttled (total events = 1)
[ 2325.000423] CPU2: Core temperature above threshold, cpu clock throttled (total events = 1)
[ 2325.001468] CPU3: Core temperature/speed normal
[ 2325.001469] CPU2: Core temperature/speed normal
[ 2398.888202] mce: [Hardware Error]: Machine check events logged
[ 2405.656279] perf interrupt took too long (5008 > 5000), lowering kernel.perf_event_max_sample_rate to 25000
[ 2652.160532] capability: warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
[ 2738.767147] usb 1-1.1: new high-speed USB device number 5 using ehci-pci
[ 2738.870367] usb 1-1.1: New USB device found, idVendor=13fe, idProduct=1f00
[ 2738.870377] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2738.870382] usb 1-1.1: Product: USB DISK 2.0
[ 2738.870387] usb 1-1.1: Manufacturer:        
[ 2738.870391] usb 1-1.1: SerialNumber: 078706A0010F
[ 2738.870930] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 2738.871566] scsi8 : usb-storage 1-1.1:1.0
[ 2739.871944] scsi 8:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 0 CCS
[ 2739.872450] sd 8:0:0:0: Attached scsi generic sg2 type 0
[ 2740.857527] sd 8:0:0:0: [sdb] 8060928 512-byte logical blocks: (4.12 GB/3.84 GiB)
[ 2740.858184] sd 8:0:0:0: [sdb] Write Protect is off
[ 2740.858187] sd 8:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 2740.858950] sd 8:0:0:0: [sdb] No Caching mode page found
[ 2740.858958] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[ 2740.862716]  sdb:
[ 2740.865432] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[ 2758.215114] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 2836.887843] usb 1-1.1: USB disconnect, device number 5
[ 2839.143100] usb 1-1.1: new high-speed USB device number 6 using ehci-pci
[ 2839.246429] usb 1-1.1: New USB device found, idVendor=13fe, idProduct=1f00
[ 2839.246437] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2839.246441] usb 1-1.1: Product: USB DISK 2.0
[ 2839.246444] usb 1-1.1: Manufacturer:        
[ 2839.246447] usb 1-1.1: SerialNumber: 078706A0010F
[ 2839.246957] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 2839.248108] scsi9 : usb-storage 1-1.1:1.0
[ 2840.247852] scsi 9:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 0 CCS
[ 2840.248435] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 2840.659579] sd 9:0:0:0: [sdb] 8060928 512-byte logical blocks: (4.12 GB/3.84 GiB)
[ 2840.660311] sd 9:0:0:0: [sdb] Write Protect is off
[ 2840.660317] sd 9:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 2840.661027] sd 9:0:0:0: [sdb] No Caching mode page found
[ 2840.661033] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[ 2840.665027]  sdb:
[ 2840.667627] sd 9:0:0:0: [sdb] Attached SCSI removable disk
[ 3132.676578] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 3223.091101] usb 1-1.1: USB disconnect, device number 6
[ 3228.579887] usb 1-1.2: new high-speed USB device number 7 using ehci-pci
[ 3228.674892] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=0109
[ 3228.674899] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3228.674903] usb 1-1.2: Product: USB2.0-CRW
[ 3228.674907] usb 1-1.2: Manufacturer: Generic
[ 3228.674910] usb 1-1.2: SerialNumber: 20090815198100000
[ 3228.685895] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 3228.686058] scsi10 : usb-storage 1-1.2:1.0
[ 3229.684443] scsi 10:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[ 3229.684935] sd 10:0:0:0: Attached scsi generic sg2 type 0
[ 3230.343397] sd 10:0:0:0: [sdb] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[ 3230.344506] sd 10:0:0:0: [sdb] Write Protect is off
[ 3230.344513] sd 10:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 3230.345664] sd 10:0:0:0: [sdb] No Caching mode page found
[ 3230.345670] sd 10:0:0:0: [sdb] Assuming drive cache: write through
[ 3230.351495]  sdb:
[ 3230.355281] sd 10:0:0:0: [sdb] Attached SCSI removable disk
[ 3245.085636] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 3768.108702] usb 1-1.2: USB disconnect, device number 7
[ 3769.594327] usb 1-1.2: new high-speed USB device number 8 using ehci-pci
[ 3769.689276] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=0109
[ 3769.689283] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3769.689287] usb 1-1.2: Product: USB2.0-CRW
[ 3769.689291] usb 1-1.2: Manufacturer: Generic
[ 3769.689294] usb 1-1.2: SerialNumber: 20090815198100000
[ 3769.700384] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 3769.700570] scsi11 : usb-storage 1-1.2:1.0
[ 3770.699003] scsi 11:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[ 3770.699606] sd 11:0:0:0: Attached scsi generic sg2 type 0
[ 3771.358859] sd 11:0:0:0: [sdb] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[ 3771.359905] sd 11:0:0:0: [sdb] Write Protect is off
[ 3771.359911] sd 11:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 3771.361038] sd 11:0:0:0: [sdb] No Caching mode page found
[ 3771.361045] sd 11:0:0:0: [sdb] Assuming drive cache: write through
[ 3771.367292]  sdb:
[ 3771.370988] sd 11:0:0:0: [sdb] Attached SCSI removable disk
[ 3825.638328] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 3980.794185] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 4382.562602] usb 1-1.2: USB disconnect, device number 8
[ 4389.482046] usb 1-1.2: new high-speed USB device number 9 using ehci-pci
[ 4389.576902] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=0109
[ 4389.576911] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4389.576915] usb 1-1.2: Product: USB2.0-CRW
[ 4389.576918] usb 1-1.2: Manufacturer: Generic
[ 4389.576921] usb 1-1.2: SerialNumber: 20090815198100000
[ 4389.588024] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 4389.588190] scsi12 : usb-storage 1-1.2:1.0
[ 4390.586552] scsi 12:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[ 4390.587761] sd 12:0:0:0: Attached scsi generic sg2 type 0
[ 4391.246820] sd 12:0:0:0: [sdb] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[ 4391.248174] sd 12:0:0:0: [sdb] Write Protect is off
[ 4391.248182] sd 12:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 4391.249237] sd 12:0:0:0: [sdb] No Caching mode page found
[ 4391.249243] sd 12:0:0:0: [sdb] Assuming drive cache: write through
[ 4391.254916]  sdb:
[ 4391.258359] sd 12:0:0:0: [sdb] Attached SCSI removable disk
[ 4426.574148] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 4581.005391] usb 1-1.2: USB disconnect, device number 9
[ 4662.322247] usb 1-1.2: new high-speed USB device number 10 using ehci-pci
[ 4662.416905] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=0109
[ 4662.416913] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4662.416917] usb 1-1.2: Product: USB2.0-CRW
[ 4662.416920] usb 1-1.2: Manufacturer: Generic
[ 4662.416923] usb 1-1.2: SerialNumber: 20090815198100000
[ 4662.427929] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 4662.428122] scsi13 : usb-storage 1-1.2:1.0
[ 4663.426562] scsi 13:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[ 4663.427140] sd 13:0:0:0: Attached scsi generic sg2 type 0
[ 4664.085586] sd 13:0:0:0: [sdb] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[ 4664.086679] sd 13:0:0:0: [sdb] Write Protect is off
[ 4664.086687] sd 13:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 4664.087786] sd 13:0:0:0: [sdb] No Caching mode page found
[ 4664.087795] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[ 4664.092672]  sdb:
[ 4664.096035] sd 13:0:0:0: [sdb] Attached SCSI removable disk
[ 4672.666915] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 4890.690551] usb 1-1.2: USB disconnect, device number 10
[ 6576.953953] CPU3: Core temperature above threshold, cpu clock throttled (total events = 3938)
[ 6576.953954] CPU2: Core temperature above threshold, cpu clock throttled (total events = 3938)
[ 6576.955000] CPU2: Core temperature/speed normal
[ 6576.955001] CPU3: Core temperature/speed normal
[ 6598.007526] mce: [Hardware Error]: Machine check events logged
[ 7683.439820] CPU2: Core temperature above threshold, cpu clock throttled (total events = 3976)
[ 7683.439821] CPU3: Core temperature above threshold, cpu clock throttled (total events = 3976)
[ 7683.440866] CPU2: Core temperature/speed normal
[ 7683.440867] CPU3: Core temperature/speed normal
[ 7797.492620] mce: [Hardware Error]: Machine check events logged
[10648.332583] usb 1-1.2: new high-speed USB device number 11 using ehci-pci
[10648.427149] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=0109
[10648.427157] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[10648.427161] usb 1-1.2: Product: USB2.0-CRW
[10648.427164] usb 1-1.2: Manufacturer: Generic
[10648.427167] usb 1-1.2: SerialNumber: 20090815198100000
[10648.438122] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[10648.438457] scsi14 : usb-storage 1-1.2:1.0
[10649.437144] scsi 14:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[10649.437753] sd 14:0:0:0: Attached scsi generic sg2 type 0
[10650.096233] sd 14:0:0:0: [sdb] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[10650.097420] sd 14:0:0:0: [sdb] Write Protect is off
[10650.097427] sd 14:0:0:0: [sdb] Mode Sense: 03 00 00 00
[10650.098543] sd 14:0:0:0: [sdb] No Caching mode page found
[10650.098549] sd 14:0:0:0: [sdb] Assuming drive cache: write through
[10650.103774]  sdb:
[10650.107492] sd 14:0:0:0: [sdb] Attached SCSI removable disk
[10950.337957] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[11010.787622] usb 1-1.2: USB disconnect, device number 11
[15033.462118] usb 1-1.2: new high-speed USB device number 12 using ehci-pci
[15033.556952] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=0109
[15033.556958] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[15033.556962] usb 1-1.2: Product: USB2.0-CRW
[15033.556966] usb 1-1.2: Manufacturer: Generic
[15033.556969] usb 1-1.2: SerialNumber: 20090815198100000
[15033.567941] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[15033.568311] scsi15 : usb-storage 1-1.2:1.0
[15033.837217] usb 1-1.2: USB disconnect, device number 12
[15034.037866] usb 1-1.2: new high-speed USB device number 13 using ehci-pci
[15034.132699] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=0109
[15034.132705] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[15034.132709] usb 1-1.2: Product: USB2.0-CRW
[15034.132713] usb 1-1.2: Manufacturer: Generic
[15034.132716] usb 1-1.2: SerialNumber: 20090815198100000
[15034.143638] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[15034.143895] scsi16 : usb-storage 1-1.2:1.0
[15035.142552] scsi 16:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[15035.143115] sd 16:0:0:0: Attached scsi generic sg2 type 0
[15035.801936] sd 16:0:0:0: [sdb] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[15035.803085] sd 16:0:0:0: [sdb] Write Protect is off
[15035.803091] sd 16:0:0:0: [sdb] Mode Sense: 03 00 00 00
[15035.804204] sd 16:0:0:0: [sdb] No Caching mode page found
[15035.804211] sd 16:0:0:0: [sdb] Assuming drive cache: write through
[15035.809705]  sdb:
[15035.813307] sd 16:0:0:0: [sdb] Attached SCSI removable disk
[16095.514904] usb 1-1.2: USB disconnect, device number 13
[16103.480041] usb 1-1.2: new high-speed USB device number 14 using ehci-pci
[16103.574877] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=0109
[16103.574884] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[16103.574888] usb 1-1.2: Product: USB2.0-CRW
[16103.574891] usb 1-1.2: Manufacturer: Generic
[16103.574895] usb 1-1.2: SerialNumber: 20090815198100000
[16103.585834] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[16103.585979] scsi17 : usb-storage 1-1.2:1.0
[16104.584610] scsi 17:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[16104.585159] sd 17:0:0:0: Attached scsi generic sg2 type 0
[16105.243374] sd 17:0:0:0: [sdb] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[16105.244474] sd 17:0:0:0: [sdb] Write Protect is off
[16105.244482] sd 17:0:0:0: [sdb] Mode Sense: 03 00 00 00
[16105.245476] sd 17:0:0:0: [sdb] No Caching mode page found
[16105.245483] sd 17:0:0:0: [sdb] Assuming drive cache: write through
[16105.250377]  sdb:
[16105.253828] sd 17:0:0:0: [sdb] Attached SCSI removable disk
[16107.223732] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[16167.058607] usb 1-1.2: USB disconnect, device number 14

#14 14-06-2015 12:33:53

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

Le dmesg me paraît normal. Par contre ce qui est curieux, c'est le
résultat de fdisk -l.  Normalement, on fait qu'une seule partion sur
un clef, là tu en aurais quatre !  Et leurs types de système de
fichiers a l'air dans les choux… Je pense que c'est n'importe quoi.
Remarque pour monter une clef on fait :


mount /dev/sdb1 /media/florian
 


Car on monte une partition. C'est possible de faire que toute la clef
ne soit qu'une seul partition, c'est à dire qu'il n'y ai pas de table
de partitions sur la clef, mais ce n'est pas l'usage courant.  De
plus, il me semble que pour windows, une table de partitions est
nécessaire.  Essaye de faire :


file -sk /dev/sdb
 


pour voir à quoi correspond ta clef. Ensuite tu peux recommencer avec
les « partitions » :


file -sk /dev/sdb1
 

Hors ligne

#15 14-06-2015 14:10:23

Anonyme-13
Invité

Re : Système de fichiers accessible en lecture seulement

enicar a écrit :

mount /dev/sdb1 /media/florian


mount: le périphérique spécial /dev/sdb1 n'existe pas


.
.
.

enicar a écrit :

file -sk /dev/sdb


/dev/sdb: DOS/MBR boot sector, code offset 0x58+2, OEM-ID "MSDOS5.0", sectors/cluster 16, reserved sectors 2412,
Media descriptor 0xf8, sectors/track 63, heads 255, sectors 31116288 (volumes > 32 MB) , FAT (32 bit), sectors/FAT 15178,
serial number 0xe8ea3280, unlabeled\012- DOS/MBR boot sector DOS/MBR boot sector DOS executable (COM), boot code


.
.
.

file -sk /dev/sdb1


/dev/sdb1: cannot open `/dev/sdb1' (No such file or directory)

#16 14-06-2015 14:14:24

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

Et que donne :


grep sdb /proc/mounts
 

Hors ligne

#17 14-06-2015 14:16:53

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

Euh, regardes plutôt :


grep sdb /proc/partitions
 

Hors ligne

#18 14-06-2015 14:29:23

Anonyme-13
Invité

Re : Système de fichiers accessible en lecture seulement

enicar a écrit :

grep sdb /proc/partitions


   8       16   15558144 sdb

#19 14-06-2015 14:32:43

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

Donc,  ta clef n'a pas de table de partition, tu es sûr que tu l'as formaté sous windows ?
Parce que là elle ressemble plus à une clef bootable du genre où on a copié une iso
d'installation.

Hors ligne

#20 14-06-2015 14:43:13

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

Aussi, regarde toutes les partitions que linux a détectées :


cat /proc/partitions
 


ou bien :


blkid
 

Hors ligne

#21 14-06-2015 15:06:25

Anonyme-13
Invité

Re : Système de fichiers accessible en lecture seulement

cat /proc/partitions

  11        0    1048575 sr0
   8        0  976762584 sda
   8        1  968785920 sda1
   8        2          1 sda2
   8        5    7973888 sda5
   8       16   15558144 sdb



blkid

/dev/sda1: UUID="e6acd7b7-af5b-47d0-a743-53a328329a34" TYPE="ext4" PARTUUID="f693bdef-01"
/dev/sda5: UUID="bc66b2e9-fb1b-4686-881c-37c6effeeb87" TYPE="swap" PARTUUID="f693bdef-05"
/dev/sdb: LABEL="USBFLO" UUID="528E-455A" TYPE="vfat"

#22 14-06-2015 15:23:06

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

C'est quoi cette clef ? Tu as essayé de booter dessus, pour voir  ?

Hors ligne

#23 14-06-2015 15:24:25

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

En fait, tu peux la monter en faisant :


mount -t vfat /dev/sdb/ /media/<rep_qui_existe>
 

Hors ligne

#24 14-06-2015 15:48:43

Anonyme-13
Invité

Re : Système de fichiers accessible en lecture seulement

La clef n'est pas bootable.

mount -t vfat /dev/sdb/ /media/disk/

mount: le périphérique spécial /dev/sdb/ n'existe pas (un préfixe de chemin n'est pas un répertoire)



J'ai le même soucis avec d'autre clef, qui non jamais été bootable.

#25 14-06-2015 15:54:04

enicar
Membre
Lieu : pas ici
Distrib. : sid
Noyau : Linux 6.5.3
(G)UI : openbox
Inscription : 26-08-2010

Re : Système de fichiers accessible en lecture seulement

En effet, j'ai rajouté involontairement un / à la fin de /dev/sdb…
La commande exacte devrait être :


mount -t vfat /dev/sdb /media/disk
 


En supposant que /media/disk est un répertoire existant.

Hors ligne

Pied de page des forums