logo Debian Debian Debian-France Debian-Facile Debian-fr.org Forum-Debian.fr Debian ? Communautés logo inclusivité

Debian-facile

Bienvenue sur Debian-Facile, site d'aide pour les nouveaux utilisateurs de Debian.

Vous n'êtes pas identifié(e).

#1 14-08-2016 09:37:05

Anonyme-13
Invité

Ajout d'une seconde carte graphique pour un 3 eme écran

Bonjour,

J'ai actuellement 2 écrans (HDMI et DVI) connectés sur une carte graphique PCIx16.

Je souhaite brancher un troisième écran, j'ai donc besoin au choix :

- D'une nouvelle carte graphique avec trois sorties HDMI PCIx16
- D'une deuxième carte graphique compatible HDMI PXCx1

Pour une question de budget je choisis la 2eme solution.

Ma question, avec la nouvelle carte graphique, la config de ma carte mère, ainsi que mon OS/Kernel,
Arandr est t'il capable de gérer les deux cartes graphiques et donc les trois écrans ?

Ma configuration actuel

PC :
Dell Inspiron 3847 / 8go / i5 / 3.5 GHz / 64Bits

Carte graphique actuel :
NVIDIA GF119 GeForce GT 705

BIOS :

Handle 0x0001, DMI type 0, 24 bytes
BIOS Information
  Vendor: Dell Inc.
  Version: A07
  Release Date: 03/03/2015
  Address: 0xF0000
  Runtime Size: 64 kB
  ROM Size: 8192 kB
  Characteristics:
    PCI is supported
    BIOS is upgradeable
    BIOS shadowing is allowed
    Boot from CD is supported
    Selectable boot is supported
    BIOS ROM is socketed
    EDD is supported
    5.25"/1.2 MB floppy services are supported (int 13h)
    3.5"/720 kB floppy services are supported (int 13h)
    3.5"/2.88 MB floppy services are supported (int 13h)
    Print screen service is supported (int 5h)
    8042 keyboard services are supported (int 9h)
    Serial services are supported (int 14h)
    Printer services are supported (int 17h)
    ACPI is supported
    USB legacy is supported
    BIOS boot specification is supported
    Targeted content distribution is supported
    UEFI is supported
  BIOS Revision: 4.6



--------------------------------------------------------------------

La nouvelle carte graphique :

Zotac GeForce GT 710 1 Go DDR3 PCI PCIe x1 passive

Lien d'achat depuis Amazon

Son futur port :

dmidecode

Handle 0x0007, DMI type 9, 17 bytes
System Slot Information
  Designation: PCIEX1
  Type: x1 PCI Express
  Current Usage: In Use
  Length: Short
  ID: 2
  Characteristics:
    3.3 V is provided
    Opening is shared
    PME signal is supported
  Bus Address: 0000:00:1c.4


lspci -vv

00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #5 (rev d5) (prog-if 00 [Normal decode])
  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
  Latency: 0, Cache Line Size: 64 bytes
  Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
  Memory behind bridge: f7100000-f71fffff
  Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
  BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
  Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
    DevCap: MaxPayload 128 bytes, PhantFunc 0
      ExtTag- RBE+
    DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
      MaxPayload 128 bytes, MaxReadReq 128 bytes
    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
    LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <16us
      ClockPM- Surprise- LLActRep+ BwNot+
    LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- CommClk+
      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
    SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
      Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
    SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
      Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
    SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
      Changed: MRL- PresDet- LinkState-
    RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
    RootCap: CRSVisible-
    RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+, OBFF Not Supported ARIFwd-
    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-
    LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
       Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
       Compliance De-emphasis: -6dB
    LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
       EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
  Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
    Address: fee00298  Data: 0000
  Capabilities: [90] Subsystem: Dell Device 0622
  Capabilities: [a0] Power Management version 3
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
  Kernel driver in use: pcieport



Merci d'avance.

Dernière modification par Anonyme-13 (14-08-2016 17:05:28)

#2 17-08-2016 19:14:11

anonyme
Invité

Re : Ajout d'une seconde carte graphique pour un 3 eme écran

Bonsoir
c'est faisable , avec le xorg.conf et nouveau par exemple comme driver (vérifier si il prend en charge tes 2 cartes )
tu configure le materiel pour chaque carte dans ce fichier ( /etc/X11/xorg.conf )

le wiki => https://debian-facile.org/doc:materiel: … ia:accueil

un exemple trés simplifié , juste pour montrer le principe


Section "Device"
Identifier  "Device0"
Driver    "nouveau"
EndSection

Section "Device"
Identifier  "Device1"
Driver    "nouveau"
EndSection

 



tu peut spécifier le numero PCI utilisé par chaque carte

la doc nvidia du site , a pas mal d info la dessus

avec beaucoup de mal un extrait du fichier doc du constructeur


To configure two separate X screens to share one graphics card, here is what you will need to do:

First, create two separate Device sections, each listing the BusID of the graphics card to be shared and listing the driver as "nvidia", and assign each a separate screen:

    Section "Device"
        Identifier  "nvidia0"
        Driver      "nvidia"
        # Edit the BusID with the location of your graphics card
        BusID       "PCI:2:0:0"
        Screen      0
    EndSection

    Section "Device"
        Identifier  "nvidia1"
        Driver      "nvidia"
        # Edit the BusID with the location of your graphics card
        BusId       "PCI:2:0:0"
        Screen      1
    EndSection

Then, create two Screen sections, each using one of the Device sections:

    Section "Screen"
        Identifier  "Screen0"
        Device      "nvidia0"
        Monitor     "Monitor0"
        DefaultDepth 24
        Subsection "Display"
            Depth       24
            Modes       "1600x1200" "1024x768" "800x600" "640x480"
        EndSubsection
    EndSection

    Section "Screen"
        Identifier  "Screen1"
        Device      "nvidia1"
        Monitor     "Monitor1"
        DefaultDepth 24
        Subsection "Display"
            Depth       24
            Modes       "1600x1200" "1024x768" "800x600" "640x480"
        EndSubsection
    EndSection
 


l exemple ci dessus pour une carte et 2 sorties
dans le cas de 2 cartes , le numero de  => BusID       "PCI:2:0:0"  change pour la deuxieme carte (a récupérer avec l utilitaire hardinfo par exemple )
PS: ceci est un exemple =>  BusID       "PCI:2:0:0" , il faut bien sur récupérer le bon de ta machine et pour chaque carte

le paquet hardinfo (utilitaire) dans section pci va te donner par exemple : bus,device,fonction  4, 0, 0
ce qui donnera la ligne => BusID  "PCI:4:0:0" (a faire pour chaque carte vidéo)
c est trés simple a mettre a faire mais dur a expliquer tongue

Dernière modification par anonyme (17-08-2016 19:44:09)

#3 17-08-2016 20:07:55

Pascal
Membre
Inscription : 02-08-2016

Re : Ajout d'une seconde carte graphique pour un 3 eme écran

Hi !

Gnux a écrit :


Je souhaite brancher un troisième écran...


Gourmand...
lol:lol::lol:
============>>>>>>>
@+

Dernière modification par Pascal (17-08-2016 20:09:00)

Hors ligne

Pied de page des forums