logo Debian Debian Debian-France Debian-Facile Debian-fr.org Forum-Debian.fr Debian ? Communautés logo inclusivité

Debian-facile

Bienvenue sur Debian-Facile, site d'aide pour les nouveaux utilisateurs de Debian.

Vous n'êtes pas identifié(e).

#1 27-01-2017 13:10:54

anonyme
Invité

[resolu]installation stretch sur PC Intel KabyLake

Bonjour
le retour des erreurs aprés installation


journalctl -r -p err
 


retour


-- Logs begin at Fri 2017-01-27 12:46:00 CET, end at Fri 2017-01-27 12:54:56 CET. --
janv. 27 12:46:19 kabylake1 udisksd[1070]: Error probing device: Error sending ATA command IDENTIFY DEVICE to /dev/sda: Unexpected sense data returned:
                                           0000: 70 00 0b 00  00 00 00 0a  00 80 00 00  47 00 00 00    p...........G...
                                           0010: 00 00 00 00  00 00 00 00  00 00 00 00  00 00 00 00    ................
                                            (g-io-error-quark, 0)
janv. 27 12:46:00 kabylake1 kernel: kvm: disabled by bios
janv. 27 12:46:00 kabylake1 kernel: i915 0000:00:02.0: firmware: failed to load i915/kbl_dmc_ver1_01.bin (-2)
janv. 27 12:46:00 kabylake1 kernel: kvm: disabled by bios
 



le retour de lspci


lspci
 


retour


00:00.0 Host bridge: Intel Corporation Device 591f (rev 05)
00:02.0 VGA compatible controller: Intel Corporation Device 5912 (rev 04)
00:14.0 USB controller: Intel Corporation Device a2af
00:16.0 Communication controller: Intel Corporation Device a2ba
00:17.0 SATA controller: Intel Corporation Device a282
00:1b.0 PCI bridge: Intel Corporation Device a2e7 (rev f0)
00:1c.0 PCI bridge: Intel Corporation Device a290 (rev f0)
00:1c.4 PCI bridge: Intel Corporation Device a294 (rev f0)
00:1d.0 PCI bridge: Intel Corporation Device a298 (rev f0)
00:1f.0 ISA bridge: Intel Corporation Device a2c5
00:1f.2 Memory controller: Intel Corporation Device a2a1
00:1f.3 Audio device: Intel Corporation Device a2f0
00:1f.4 SMBus: Intel Corporation Device a2a3
00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection (5) I219-V
01:00.0 SATA controller: Kingston Technologies Device 0010 (rev 10)
03:00.0 USB controller: ASMedia Technology Inc. Device 2142
 



-pour KVM , je dois l activer dans le bios (virtualization )

-pour "udisksd" j avais le meme souci sur le serveur avec une carte file sur connecteur PCIe et un module M2
nota : sur la carte mère j'ai 2 logements M2 (un Sata/PCIe et l autre PCIe uniquement) actuellement je suis sur PCIe uniquement

-il me manque le firmware de la carte réseau intel " firmware: failed to load i915/kbl_dmc_ver1_01.bin (-2) "  (mais le réseau fonctionne )

le log du serveur X a l'air correct (écran vieux Belinea 17 pouces en HDMI en 4/3 )


cat /var/log/Xorg.0.log
 


retour


[     8.764] X.Org X Server 1.19.0 Release Date: 2016-11-15
[     8.764] X Protocol Version 11, Revision 0
[     8.764] Build Operating System: Linux 3.16.0-4-amd64 x86_64 Debian
[     8.764] Current Operating System: Linux kabylake1 4.9.0-1-amd64 #1 SMP Debian 4.9.2-2 (2017-01-12) x86_64
[     8.764] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-1-amd64 root=UUID=32dbc53b-c168-42fc-88bb-0847713aac4b ro quiet
[     8.764] Build Date: 16 December 2016  07:30:27PM
[     8.764] xorg-server 2:1.19.0-3 (https://www.debian.org/support)
[     8.764] Current version of pixman: 0.34.0
[     8.764]  Before reporting problems, check http://wiki.x.org
  to make sure that you have the latest version.
[     8.764] Markers: (--) probed, (**) from config file, (==) default setting,
  (++) from command line, (!!) notice, (II) informational,
  (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[     8.764] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Jan 27 12:46:07 2017
[     8.764] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[     8.765] (==) No Layout section.  Using the first Screen section.
[     8.765] (==) No screen section available. Using defaults.
[     8.765] (**) |-->Screen "Default Screen Section" (0)
[     8.765] (**) |   |-->Monitor "<default monitor>"
[     8.766] (==) No monitor specified for screen "Default Screen Section".
  Using a default monitor configuration.
[     8.766] (==) Automatically adding devices
[     8.766] (==) Automatically enabling devices
[     8.766] (==) Automatically adding GPU devices
[     8.766] (==) Max clients allowed: 256, resource mask: 0x1fffff
[     8.767] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[     8.767]  Entry deleted from font path.
[     8.767] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[     8.767]  Entry deleted from font path.
[     8.767] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[     8.767]  Entry deleted from font path.
[     8.767] (WW) The directory "/usr/share/fonts/X11/Type1" does not exist.
[     8.767]  Entry deleted from font path.
[     8.767] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[     8.767]  Entry deleted from font path.
[     8.767] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[     8.767]  Entry deleted from font path.
[     8.767] (==) FontPath set to:
  /usr/share/fonts/X11/misc,
  built-ins
[     8.767] (==) ModulePath set to "/usr/lib/xorg/modules"
[     8.767] (II) The server relies on udev to provide the list of input devices.
  If no devices become available, reconfigure udev or disable AutoAddDevices.
[     8.767] (II) Loader magic: 0x5586c7055e00
[     8.767] (II) Module ABI versions:
[     8.767]  X.Org ANSI C Emulation: 0.4
[     8.767]  X.Org Video Driver: 23.0
[     8.767]  X.Org XInput driver : 24.1
[     8.767]  X.Org Server Extension : 10.0
[     8.768] (++) using VT number 7

[     8.768] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[     8.768] (II) xfree86: Adding drm device (/dev/dri/card0)
[     8.784] (--) PCI:*(0:0:2:0) 8086:5912:1043:872f rev 4, Mem @ 0xde000000/16777216, 0xc0000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072
[     8.784] (II) LoadModule: "glx"
[     8.785] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[     8.792] (II) Module glx: vendor="X.Org Foundation"
[     8.792]  compiled for 1.19.0, module version = 1.0.0
[     8.792]  ABI class: X.Org Server Extension, version 10.0
[     8.792] (==) Matched modesetting as autoconfigured driver 0
[     8.792] (==) Matched fbdev as autoconfigured driver 1
[     8.792] (==) Matched vesa as autoconfigured driver 2
[     8.792] (==) Assigned the driver to the xf86ConfigLayout
[     8.792] (II) LoadModule: "modesetting"
[     8.793] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[     8.793] (II) Module modesetting: vendor="X.Org Foundation"
[     8.793]  compiled for 1.19.0, module version = 1.19.0
[     8.793]  Module class: X.Org Video Driver
[     8.793]  ABI class: X.Org Video Driver, version 23.0
[     8.793] (II) LoadModule: "fbdev"
[     8.793] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[     8.794] (II) Module fbdev: vendor="X.Org Foundation"
[     8.794]  compiled for 1.19.0, module version = 0.4.4
[     8.794]  Module class: X.Org Video Driver
[     8.794]  ABI class: X.Org Video Driver, version 23.0
[     8.794] (II) LoadModule: "vesa"
[     8.794] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[     8.794] (II) Module vesa: vendor="X.Org Foundation"
[     8.794]  compiled for 1.19.0, module version = 2.3.4
[     8.794]  Module class: X.Org Video Driver
[     8.794]  ABI class: X.Org Video Driver, version 23.0
[     8.794] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[     8.794] (II) FBDEV: driver for framebuffer: fbdev
[     8.794] (II) VESA: driver for VESA chipsets: vesa
[     8.817] (II) modeset(0): using drv /dev/dri/card0
[     8.817] (WW) Falling back to old probe method for fbdev
[     8.817] (II) Loading sub module "fbdevhw"
[     8.817] (II) LoadModule: "fbdevhw"
[     8.817] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[     8.819] (II) Module fbdevhw: vendor="X.Org Foundation"
[     8.819]  compiled for 1.19.0, module version = 0.0.2
[     8.819]  ABI class: X.Org Video Driver, version 23.0
[     8.819] (WW) Falling back to old probe method for vesa
[     8.819] (II) modeset(0): Creating default Display subsection in Screen section
  "Default Screen Section" for depth/fbbpp 24/32
[     8.819] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[     8.819] (==) modeset(0): RGB weight 888
[     8.819] (==) modeset(0): Default visual is TrueColor
[     8.819] (II) Loading sub module "glamoregl"
[     8.819] (II) LoadModule: "glamoregl"
[     8.819] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[     8.833] (II) Module glamoregl: vendor="X.Org Foundation"
[     8.833]  compiled for 1.19.0, module version = 1.0.0
[     8.833]  ABI class: X.Org ANSI C Emulation, version 0.4
[     8.833] (II) glamor: OpenGL accelerated X.org driver based.
[     8.870] (II) glamor: EGL version 1.4 (DRI2):
[     8.880] (II) modeset(0): glamor initialized
[     8.880] (II) modeset(0): Output DP-1 has no monitor section
[     8.882] (II) modeset(0): Output HDMI-1 has no monitor section
[     8.883] (II) modeset(0): Output HDMI-2 has no monitor section
[     8.897] (II) modeset(0): Output HDMI-3 has no monitor section
[     8.897] (II) modeset(0): EDID for output DP-1
[     8.898] (II) modeset(0): EDID for output HDMI-1
[     8.899] (II) modeset(0): EDID for output HDMI-2
[     8.912] (II) modeset(0): EDID for output HDMI-3
[     8.912] (II) modeset(0): Manufacturer: MAX  Model: 6e0  Serial#: 16843009
[     8.912] (II) modeset(0): Year: 2007  Week: 38
[     8.912] (II) modeset(0): EDID Version: 1.3
[     8.912] (II) modeset(0): Digital Display Input
[     8.913] (II) modeset(0): Max Image Size [cm]: horiz.: 34  vert.: 27
[     8.913] (II) modeset(0): Gamma: 2.20
[     8.913] (II) modeset(0): DPMS capabilities: StandBy Suspend Off
[     8.913] (II) modeset(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[     8.913] (II) modeset(0): First detailed timing is preferred mode
[     8.913] (II) modeset(0): redX: 0.639 redY: 0.342   greenX: 0.297 greenY: 0.615
[     8.913] (II) modeset(0): blueX: 0.146 blueY: 0.068   whiteX: 0.313 whiteY: 0.329
[     8.913] (II) modeset(0): Supported established timings:
[     8.913] (II) modeset(0): 720x400@70Hz
[     8.913] (II) modeset(0): 640x480@60Hz
[     8.913] (II) modeset(0): 640x480@67Hz
[     8.913] (II) modeset(0): 640x480@72Hz
[     8.913] (II) modeset(0): 640x480@75Hz
[     8.913] (II) modeset(0): 800x600@60Hz
[     8.913] (II) modeset(0): 800x600@72Hz
[     8.913] (II) modeset(0): 800x600@75Hz
[     8.913] (II) modeset(0): 832x624@75Hz
[     8.913] (II) modeset(0): 1024x768@60Hz
[     8.913] (II) modeset(0): 1024x768@70Hz
[     8.913] (II) modeset(0): 1024x768@75Hz
[     8.913] (II) modeset(0): 1280x1024@75Hz
[     8.913] (II) modeset(0): 1152x864@75Hz
[     8.913] (II) modeset(0): Manufacturer's mask: 0
[     8.913] (II) modeset(0): Supported standard timings:
[     8.913] (II) modeset(0): #0: hsize: 1152  vsize 864  refresh: 75  vid: 20337
[     8.913] (II) modeset(0): #1: hsize: 1280  vsize 1024  refresh: 76  vid: 36993
[     8.913] (II) modeset(0): #2: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[     8.913] (II) modeset(0): #3: hsize: 1280  vsize 1024  refresh: 72  vid: 35969
[     8.913] (II) modeset(0): #4: hsize: 800  vsize 600  refresh: 75  vid: 20293
[     8.913] (II) modeset(0): #5: hsize: 1024  vsize 768  refresh: 60  vid: 16481
[     8.913] (II) modeset(0): Supported detailed timing:
[     8.913] (II) modeset(0): clock: 108.0 MHz   Image Size:  376 x 301 mm
[     8.913] (II) modeset(0): h_active: 1280  h_sync: 1328  h_sync_end 1440 h_blank_end 1688 h_border: 0
[     8.913] (II) modeset(0): v_active: 1024  v_sync: 1025  v_sync_end 1028 v_blanking: 1066 v_border: 0
[     8.913] (II) modeset(0): Ranges: V min: 55 V max: 76 Hz, H min: 31 H max: 81 kHz, PixClock max 145 MHz
[     8.913] (II) modeset(0): Monitor name: Bel101728
[     8.913] (II) modeset(0): Serial No: 073810408399
[     8.913] (II) modeset(0): EDID (in hex):
[     8.913] (II) modeset(0):   00ffffffffffff003438e00601010101
[     8.913] (II) modeset(0):   2611010380221b78eaa2a5a3574c9d25
[     8.913] (II) modeset(0):   115054bdef80714f81908180818c454f
[     8.913] (II) modeset(0):   614001010101302a009851002a403070
[     8.913] (II) modeset(0):   1300782d1100001e000000fd00374c1f
[     8.913] (II) modeset(0):   510e000a202020202020000000fc0042
[     8.913] (II) modeset(0):   656c3130313732380a0a0a0a000000ff
[     8.913] (II) modeset(0):   003037333831303430383339390a002b
[     8.913] (II) modeset(0): Printing probed modes for output HDMI-3
[     8.913] (II) modeset(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz eP)
[     8.913] (II) modeset(0): Modeline "1280x1024"x76.0  141.81  1280 1376 1512 1744  1024 1025 1028 1070 -hsync +vsync (81.3 kHz)
[     8.913] (II) modeset(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[     8.913] (II) modeset(0): Modeline "1280x1024"x72.0  132.84  1280 1368 1504 1728  1024 1025 1028 1067 -hsync +vsync (76.9 kHz)
[     8.913] (II) modeset(0): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[     8.913] (II) modeset(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[     8.913] (II) modeset(0): Modeline "1024x768"x70.1   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[     8.913] (II) modeset(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[     8.913] (II) modeset(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[     8.913] (II) modeset(0): Modeline "800x600"x72.2   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[     8.913] (II) modeset(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[     8.913] (II) modeset(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[     8.913] (II) modeset(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[     8.913] (II) modeset(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz e)
[     8.913] (II) modeset(0): Modeline "640x480"x66.7   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
[     8.913] (II) modeset(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[     8.913] (II) modeset(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[     8.913] (II) modeset(0): Output DP-1 disconnected
[     8.914] (II) modeset(0): Output HDMI-1 disconnected
[     8.914] (II) modeset(0): Output HDMI-2 disconnected
[     8.914] (II) modeset(0): Output HDMI-3 connected
[     8.914] (II) modeset(0): Using exact sizes for initial modes
[     8.914] (II) modeset(0): Output HDMI-3 using initial mode 1280x1024 +0+0
[     8.914] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)
[     8.914] (==) modeset(0): DPI set to (96, 96)
[     8.914] (II) Loading sub module "fb"
[     8.914] (II) LoadModule: "fb"
[     8.914] (II) Loading /usr/lib/xorg/modules/libfb.so
[     8.915] (II) Module fb: vendor="X.Org Foundation"
[     8.915]  compiled for 1.19.0, module version = 1.0.0
[     8.915]  ABI class: X.Org ANSI C Emulation, version 0.4
[     8.915] (II) UnloadModule: "fbdev"
[     8.915] (II) Unloading fbdev
[     8.915] (II) UnloadSubModule: "fbdevhw"
[     8.915] (II) Unloading fbdevhw
[     8.915] (II) UnloadModule: "vesa"
[     8.915] (II) Unloading vesa
[     8.915] (==) Depth 24 pixmap format is 32 bpp
[     8.990] (==) modeset(0): Backing store enabled
[     8.990] (==) modeset(0): Silken mouse enabled
[     8.990] (II) modeset(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[     9.020] (==) modeset(0): DPMS enabled
[     9.020] (II) modeset(0): [DRI2] Setup complete
[     9.020] (II) modeset(0): [DRI2]   DRI driver: i965
[     9.020] (II) modeset(0): [DRI2]   VDPAU driver: i965
[     9.020] (--) RandR disabled
[     9.022] (II) SELinux: Disabled on system
[     9.025] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[     9.025] (II) AIGLX: enabled GLX_ARB_create_context
[     9.025] (II) AIGLX: enabled GLX_ARB_create_context_profile
[     9.025] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile
[     9.025] (II) AIGLX: enabled GLX_INTEL_swap_event
[     9.025] (II) AIGLX: enabled GLX_SGI_swap_control
[     9.025] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[     9.025] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[     9.025] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float
[     9.025] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[     9.025] (II) AIGLX: enabled GLX_ARB_create_context_robustness
[     9.025] (II) AIGLX: Loaded and initialized i965
[     9.025] (II) GLX: Initialized DRI2 GL provider for screen 0
[     9.027] (II) modeset(0): Damage tracking initialized
[     9.027] (II) modeset(0): Setting screen physical size to 338 x 270
[     9.054] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[     9.054] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[     9.054] (II) LoadModule: "libinput"
[     9.054] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[     9.057] (II) Module libinput: vendor="X.Org Foundation"
[     9.057]  compiled for 1.19.0, module version = 0.23.0
[     9.057]  Module class: X.Org XInput Driver
[     9.057]  ABI class: X.Org XInput driver, version 24.1
[     9.057] (II) Using input driver 'libinput' for 'Power Button'
[     9.057] (**) Power Button: always reports core events
[     9.057] (**) Option "Device" "/dev/input/event4"
[     9.057] (**) Option "_source" "server/udev"
[     9.057] (II) input device 'Power Button', /dev/input/event4 is tagged by udev as: Keyboard
[     9.057] (II) input device 'Power Button', /dev/input/event4 is a keyboard
[     9.084] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event4"
[     9.084] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[     9.084] (**) Option "xkb_model" "pc105"
[     9.084] (**) Option "xkb_layout" "fr"
[     9.084] (**) Option "xkb_variant" "latin9"
[     9.115] (II) input device 'Power Button', /dev/input/event4 is tagged by udev as: Keyboard
[     9.115] (II) input device 'Power Button', /dev/input/event4 is a keyboard
[     9.115] (II) config/udev: Adding input device Video Bus (/dev/input/event7)
[     9.115] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[     9.115] (II) Using input driver 'libinput' for 'Video Bus'
[     9.115] (**) Video Bus: always reports core events
[     9.115] (**) Option "Device" "/dev/input/event7"
[     9.115] (**) Option "_source" "server/udev"
[     9.115] (II) input device 'Video Bus', /dev/input/event7 is tagged by udev as: Keyboard
[     9.115] (II) input device 'Video Bus', /dev/input/event7 is a keyboard
[     9.132] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7/event7"
[     9.132] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[     9.132] (**) Option "xkb_model" "pc105"
[     9.132] (**) Option "xkb_layout" "fr"
[     9.132] (**) Option "xkb_variant" "latin9"
[     9.132] (II) input device 'Video Bus', /dev/input/event7 is tagged by udev as: Keyboard
[     9.132] (II) input device 'Video Bus', /dev/input/event7 is a keyboard
[     9.132] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[     9.132] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[     9.132] (II) Using input driver 'libinput' for 'Power Button'
[     9.132] (**) Power Button: always reports core events
[     9.132] (**) Option "Device" "/dev/input/event3"
[     9.132] (**) Option "_source" "server/udev"
[     9.132] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard
[     9.132] (II) input device 'Power Button', /dev/input/event3 is a keyboard
[     9.156] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3/event3"
[     9.156] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[     9.156] (**) Option "xkb_model" "pc105"
[     9.156] (**) Option "xkb_layout" "fr"
[     9.156] (**) Option "xkb_variant" "latin9"
[     9.156] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard
[     9.156] (II) input device 'Power Button', /dev/input/event3 is a keyboard
[     9.156] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[     9.156] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[     9.156] (II) Using input driver 'libinput' for 'Sleep Button'
[     9.156] (**) Sleep Button: always reports core events
[     9.156] (**) Option "Device" "/dev/input/event2"
[     9.156] (**) Option "_source" "server/udev"
[     9.156] (II) input device 'Sleep Button', /dev/input/event2 is tagged by udev as: Keyboard
[     9.156] (II) input device 'Sleep Button', /dev/input/event2 is a keyboard
[     9.172] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2/event2"
[     9.172] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[     9.172] (**) Option "xkb_model" "pc105"
[     9.172] (**) Option "xkb_layout" "fr"
[     9.172] (**) Option "xkb_variant" "latin9"
[     9.172] (II) input device 'Sleep Button', /dev/input/event2 is tagged by udev as: Keyboard
[     9.172] (II) input device 'Sleep Button', /dev/input/event2 is a keyboard
[     9.173] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event1)
[     9.173] (**) Logitech USB Optical Mouse: Applying InputClass "libinput pointer catchall"
[     9.173] (II) Using input driver 'libinput' for 'Logitech USB Optical Mouse'
[     9.174] (**) Logitech USB Optical Mouse: always reports core events
[     9.174] (**) Option "Device" "/dev/input/event1"
[     9.174] (**) Option "_source" "server/udev"
[     9.174] (II) input device 'Logitech USB Optical Mouse', /dev/input/event1 is tagged by udev as: Mouse
[     9.174] (II) Device 'Logitech USB Optical Mouse' set to 1000 DPI
[     9.174] (II) input device 'Logitech USB Optical Mouse', /dev/input/event1 is a pointer caps
[     9.204] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/0003:046D:C05A.0001/input/input1/event1"
[     9.204] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE, id 10)
[     9.204] (**) Option "AccelerationScheme" "none"
[     9.204] (**) Logitech USB Optical Mouse: (accel) selected scheme none/0
[     9.204] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000
[     9.204] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4
[     9.205] (II) input device 'Logitech USB Optical Mouse', /dev/input/event1 is tagged by udev as: Mouse
[     9.205] (II) Device 'Logitech USB Optical Mouse' set to 1000 DPI
[     9.205] (II) input device 'Logitech USB Optical Mouse', /dev/input/event1 is a pointer caps
[     9.206] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/mouse0)
[     9.206] (II) No input driver specified, ignoring this device.
[     9.206] (II) This device may have been added with another device file.
[     9.206] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event10)
[     9.206] (II) No input driver specified, ignoring this device.
[     9.206] (II) This device may have been added with another device file.
[     9.207] (II) config/udev: Adding input device HDA Intel PCH Line Out Front (/dev/input/event11)
[     9.207] (II) No input driver specified, ignoring this device.
[     9.207] (II) This device may have been added with another device file.
[     9.207] (II) config/udev: Adding input device HDA Intel PCH Line Out Surround (/dev/input/event12)
[     9.207] (II) No input driver specified, ignoring this device.
[     9.207] (II) This device may have been added with another device file.
[     9.208] (II) config/udev: Adding input device HDA Intel PCH Line Out CLFE (/dev/input/event13)
[     9.208] (II) No input driver specified, ignoring this device.
[     9.208] (II) This device may have been added with another device file.
[     9.208] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event14)
[     9.208] (II) No input driver specified, ignoring this device.
[     9.208] (II) This device may have been added with another device file.
[     9.209] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event15)
[     9.209] (II) No input driver specified, ignoring this device.
[     9.209] (II) This device may have been added with another device file.
[     9.209] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event16)
[     9.209] (II) No input driver specified, ignoring this device.
[     9.209] (II) This device may have been added with another device file.
[     9.210] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event8)
[     9.210] (II) No input driver specified, ignoring this device.
[     9.210] (II) This device may have been added with another device file.
[     9.210] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event9)
[     9.210] (II) No input driver specified, ignoring this device.
[     9.210] (II) This device may have been added with another device file.
[     9.211] (II) config/udev: Adding input device Eee PC WMI hotkeys (/dev/input/event6)
[     9.211] (**) Eee PC WMI hotkeys: Applying InputClass "libinput keyboard catchall"
[     9.211] (II) Using input driver 'libinput' for 'Eee PC WMI hotkeys'
[     9.211] (**) Eee PC WMI hotkeys: always reports core events
[     9.211] (**) Option "Device" "/dev/input/event6"
[     9.211] (**) Option "_source" "server/udev"
[     9.211] (II) input device 'Eee PC WMI hotkeys', /dev/input/event6 is tagged by udev as: Keyboard
[     9.211] (II) input device 'Eee PC WMI hotkeys', /dev/input/event6 is a keyboard
[     9.228] (**) Option "config_info" "udev:/sys/devices/platform/eeepc-wmi/input/input6/event6"
[     9.228] (II) XINPUT: Adding extended input device "Eee PC WMI hotkeys" (type: KEYBOARD, id 11)
[     9.228] (**) Option "xkb_model" "pc105"
[     9.228] (**) Option "xkb_layout" "fr"
[     9.228] (**) Option "xkb_variant" "latin9"
[     9.229] (II) input device 'Eee PC WMI hotkeys', /dev/input/event6 is tagged by udev as: Keyboard
[     9.229] (II) input device 'Eee PC WMI hotkeys', /dev/input/event6 is a keyboard
[     9.229] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[     9.229] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[     9.229] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[     9.229] (**) AT Translated Set 2 keyboard: always reports core events
[     9.229] (**) Option "Device" "/dev/input/event0"
[     9.229] (**) Option "_source" "server/udev"
[     9.230] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard
[     9.230] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard
[     9.244] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[     9.244] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 12)
[     9.244] (**) Option "xkb_model" "pc105"
[     9.244] (**) Option "xkb_layout" "fr"
[     9.244] (**) Option "xkb_variant" "latin9"
[     9.245] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard
[     9.245] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard
[     9.245] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)
[     9.245] (II) No input driver specified, ignoring this device.
[     9.245] (II) This device may have been added with another device file.
[    21.087] (II) modeset(0): EDID vendor "MAX", prod id 1760
[    21.087] (II) modeset(0): Using EDID range info for horizontal sync
[    21.087] (II) modeset(0): Using EDID range info for vertical refresh
[    21.087] (II) modeset(0): Printing DDC gathered Modelines:
[    21.087] (II) modeset(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz eP)
[    21.087] (II) modeset(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    21.087] (II) modeset(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    21.087] (II) modeset(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz e)
[    21.087] (II) modeset(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
[    21.087] (II) modeset(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    21.087] (II) modeset(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    21.087] (II) modeset(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    21.087] (II) modeset(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    21.087] (II) modeset(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[    21.087] (II) modeset(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    21.087] (II) modeset(0): Modeline "832x624"x0.0   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    21.087] (II) modeset(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    21.087] (II) modeset(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[    21.087] (II) modeset(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[    21.087] (II) modeset(0): Modeline "1280x1024"x76.0  141.82  1280 1376 1512 1744  1024 1025 1028 1070 -hsync +vsync (81.3 kHz e)
[    21.087] (II) modeset(0): Modeline "1280x1024"x72.0  132.75  1280 1368 1504 1728  1024 1025 1028 1067 -hsync +vsync (76.8 kHz e)
[    21.103] (II) modeset(0): EDID vendor "MAX", prod id 1760
[    21.103] (II) modeset(0): Using hsync ranges from config file
[    21.103] (II) modeset(0): Using vrefresh ranges from config file
[    21.103] (II) modeset(0): Printing DDC gathered Modelines:
[    21.103] (II) modeset(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz eP)
[    21.103] (II) modeset(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    21.103] (II) modeset(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    21.103] (II) modeset(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz e)
[    21.103] (II) modeset(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
[    21.103] (II) modeset(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    21.103] (II) modeset(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    21.103] (II) modeset(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    21.103] (II) modeset(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    21.103] (II) modeset(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[    21.103] (II) modeset(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    21.103] (II) modeset(0): Modeline "832x624"x0.0   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    21.103] (II) modeset(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    21.103] (II) modeset(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[    21.103] (II) modeset(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[    21.103] (II) modeset(0): Modeline "1280x1024"x76.0  141.82  1280 1376 1512 1744  1024 1025 1028 1070 -hsync +vsync (81.3 kHz e)
[    21.103] (II) modeset(0): Modeline "1280x1024"x72.0  132.75  1280 1368 1504 1728  1024 1025 1028 1067 -hsync +vsync (76.8 kHz e)
[    21.120] (II) modeset(0): EDID vendor "MAX", prod id 1760
[    21.120] (II) modeset(0): Using hsync ranges from config file
[    21.120] (II) modeset(0): Using vrefresh ranges from config file
[    21.120] (II) modeset(0): Printing DDC gathered Modelines:
[    21.120] (II) modeset(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz eP)
[    21.120] (II) modeset(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    21.120] (II) modeset(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    21.120] (II) modeset(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz e)
[    21.120] (II) modeset(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
[    21.120] (II) modeset(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    21.120] (II) modeset(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    21.120] (II) modeset(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    21.120] (II) modeset(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    21.120] (II) modeset(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[    21.120] (II) modeset(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    21.120] (II) modeset(0): Modeline "832x624"x0.0   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    21.120] (II) modeset(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    21.120] (II) modeset(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[    21.120] (II) modeset(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[    21.120] (II) modeset(0): Modeline "1280x1024"x76.0  141.82  1280 1376 1512 1744  1024 1025 1028 1070 -hsync +vsync (81.3 kHz e)
[    21.120] (II) modeset(0): Modeline "1280x1024"x72.0  132.75  1280 1368 1504 1728  1024 1025 1028 1067 -hsync +vsync (76.8 kHz e)
[    21.136] (II) modeset(0): EDID vendor "MAX", prod id 1760
[    21.136] (II) modeset(0): Using hsync ranges from config file
[    21.136] (II) modeset(0): Using vrefresh ranges from config file
[    21.136] (II) modeset(0): Printing DDC gathered Modelines:
[    21.136] (II) modeset(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz eP)
[    21.136] (II) modeset(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    21.136] (II) modeset(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    21.136] (II) modeset(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz e)
[    21.136] (II) modeset(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
[    21.136] (II) modeset(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    21.136] (II) modeset(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    21.136] (II) modeset(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    21.136] (II) modeset(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    21.136] (II) modeset(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[    21.136] (II) modeset(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    21.136] (II) modeset(0): Modeline "832x624"x0.0   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    21.136] (II) modeset(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    21.136] (II) modeset(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[    21.136] (II) modeset(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[    21.136] (II) modeset(0): Modeline "1280x1024"x76.0  141.82  1280 1376 1512 1744  1024 1025 1028 1070 -hsync +vsync (81.3 kHz e)
[    21.136] (II) modeset(0): Modeline "1280x1024"x72.0  132.75  1280 1368 1504 1728  1024 1025 1028 1067 -hsync +vsync (76.8 kHz e)
 

Dernière modification par anonyme (09-02-2017 01:43:38)

#2 27-01-2017 13:50:45

anonyme
Invité

Re : [resolu]installation stretch sur PC Intel KabyLake

j'ai installé le paquet "firmware-misc-nonfree" , activé VT dans le bios
il me reste ceci :


journalctl -r -p err
 


retour


-- Logs begin at Fri 2017-01-27 13:35:49 CET, end at Fri 2017-01-27 13:38:19 CET. --
janv. 27 13:36:12 kabylake1 udisksd[1005]: Error probing device: Error sending ATA command IDENTIFY DEVICE to /dev/sda: Unexpected sense data returned:
                                           0000: 70 00 0b 00  00 00 00 0a  00 80 00 00  47 00 00 00    p...........G...
                                           0010: 00 00 00 00  00 00 00 00  00 00 00 00  00 00 00 00    ................
                                            (g-io-error-quark, 0)
 


utiliser l autre M2  peut etre

stretch assure quand meme je pensais avoir plus de problèmes roll

j'ai installé le paquet libre vulkan qui prend en charge les gpu intel
ps: c'est très fluide par rapport au I3 en Skylake et ddr3
description:
la carte mère "PRIME Z270-A"  Asus , ddr4 2400 , I7 7700 (3.6Ghz ) ssd M2 Kingstone 256G hyper X prédator

Dernière modification par anonyme (27-01-2017 13:52:39)

#3 27-01-2017 20:38:17

anonyme
Invité

Re : [resolu]installation stretch sur PC Intel KabyLake

le basculement du module SSD M2 sur le deuxieme emplacement renvoie la meme erreur (le premier me bloque l utilisation du sata 5-6 , le second le connecteur sata 1 )
A priori debian ne prend pas convenablement en compte ce type de SSD (je sais pas si les commandes sont  en AHCI ou spécifiques au lien PCIe)
je connais pas encore bien , peut etre une option dans le bios.

#4 08-02-2017 00:03:14

anonyme
Invité

Re : [resolu]installation stretch sur PC Intel KabyLake

Bonsoir
bon rien ne va plus ............... hmm

aujourd'hui j'ai voulu mettre la machine dans son boitier , le problème a commencé par le voyant d'activité des disques dur allumé en permanence .
j'ai mit a jour le bios (0502 => 0701 )  plus de réseau (le noyau donne une erreur )


e1000e 0000:00:1f.6: The NVM Checksum Is Not Valid
 



journalctl -r -p err
 



-- Logs begin at Tue 2017-02-07 22:48:55 CET, end at Tue 2017-02-07 23:04:43 CET. --
févr. 07 22:48:57 kabylake1 kernel: e1000e 0000:00:1f.6: The NVM Checksum Is Not Valid
 


pour enlever le souci d'activité du disque dur , j'ai retiré le module PCIe
pour le réseau j'ai mit une carte realtek PCIe 1Gbs

bien sur nouvelle installation sur DD 1T0  en mode UEFI (tant qu on y est roll  tongue  )

tout est correct pour l instant

nota : pour le module PCIe aucune explication , je n'ai qu un model et je sais pas si souci coté carte mère ou coté module ssd .
pour la carte réseau intel i219-v   (e1000e) elle a fonctionné avec le bios 0502 et plus maintenant .

Dernière modification par anonyme (08-02-2017 01:22:19)

#5 09-02-2017 00:50:17

anonyme
Invité

Re : [resolu]installation stretch sur PC Intel KabyLake

Bonsoir
j'ai trouvé quelques réponses pour ce problème "The NVM Checksum Is Not Valid"
la solution serait d'utiliser les commandes "ethtool" du meme paquet sur debian.
mais ça commence mal , il me faut forcer le noyau a configurer la carte .
j' ai trouvé un script mais je sais comment le mettre en place sur debian.
il parle d un dossier /src le seul que j'ai trouvé se trouve dans /usr/src


for (i = 0; false; i++) {
    if (e1000_validate_nvm_checksum(&adapter->hw) >= 0)
        break;
    if (i == 2) {
        dev_err(pci_dev_to_dev(pdev),
            "The NVM Checksum Is Not Valid\n");
        err = -EIO;
        goto err_eeprom;
    }
}
 


le placer dans file src/netdev.c
et faire une installation du patch


sudo make install
sudo modprobe -r e1000e
sudo modprobe e1000e
sudo update-initramfs -u
reboot
 


ce qui donne "Now the checksum validation was skipped and the Ethernet started working."
la carte est configuré par le noyau et je peu utiliser ethtool pour réparer le checksum de la carte réseau.
le plus simple hmm
lire la valeur


ethtool -e enp0s31f6 offset 0x10 length 1
 


ecrire la nouvelle valeur


ethtool -E enp0s31f6 magic 0x15708086 offset 0x10 value 0xff
 


enlever le patch ci dessus et redémarrer.

sinon j'ai testé plusieurs bios (dont celui d origine du dvd ) sans résultat
pour la référence du bios c'est la bonne
c'est la première fois que ça m arrive sur une mise a jour d un bios
l eeprom réseau serait dans la puce de la carte réseau
a part prendre des cours d informatique pour le moment c'est flou tout ça  roll

l'utilitaire intel , par un boot "dos" ou par debian ne fonctionne pas . (Windows pas testé )

le lien de ma source : http://superuser.com/questions/1104537/ … co/1106641
nota: je sais pas si sérieux rien trouvé de mieux

Dernière modification par anonyme (09-02-2017 00:54:51)

#6 09-02-2017 01:42:28

anonyme
Invité

Re : [resolu]installation stretch sur PC Intel KabyLake

re

j'ai trouvé plus simple (voir la fin du lien ci dessus meme carte mère que moi )
récupéré l utilitaire intel (dossier linux 64 pour moi )


chmod +x ./bootutil64e
 



 ./bootutil64e -NIC 1 -defcfg
 


et j ai retrouvé ma carte en état de fonctionné après reboot  smile

problème résolu jusqu a la prochaine mise a jour du bios  hmm

nota : pour le problème du ssd kingstone predator M2 PCIe  j'ai récupéré un firmware mais je me fais pas trop d'illusion.
il me faut une machine en windows pour effectuer la mise a jour.
sur leur site aucune allusion au problème que je donne en #2 et #4 , juste correctif pour win10  hmm
le module peut etre utilisé en M2 PCIe x4  ou sur carte file PCIe de leur marque
il parle de carte asus Z170 et du mode raid comme problème
sur une carte H170-D3 je n ai aucun souci avec un ssd M2 crucial sous stretch
j'ai 2 modules (un avec carte file l autre sans j aimerai bien qu il fonctionne correctement  roll  )
ps: sur la carte mère kabylake je peut pas tester avec la carte file (plus de connecteur libre neutral  ) et de plus avoir 2 logements M2 qui fonctionne mal pas trés cool hmm

j'ai un module ssd M2 sata avec les encoches M key et B key  qui fonctionne correctement ( mode sata3 )
et 2 modules ssd M2 PCIe  avec uniquement l encoche M key  qui posent problème . (différent selon l utilisation sur port M2 ou sur carte file PCIe ) (mode PCIe )
si quelqu'un utilise ce type de ssd M2 sous debian .  roll
je vais essayer de faire quelques test sous win ....  hmm

ps: la mise a jour du firmware ne fonctionne pas sous win10 , je pense que je vais rester sur la marque Crucial pour les ssd  roll

Dernière modification par anonyme (09-02-2017 08:40:08)

#7 09-02-2017 19:00:11

yoshi
Membre
Lieu : Normandie
Distrib. : LMDE 6 Faye
Noyau : 6.6.5-1-liquorix-amd64
(G)UI : Cinnamon 5.8.4
Inscription : 05-03-2014

Re : [resolu]installation stretch sur PC Intel KabyLake

Hello anonyme !

Comme quoi, tu vois, le matériel de dernière génération, sous Linux, c'est pas toujours évident.
Mais généralement c'est quand même assez rapidement supporté.
Il y a pire: exemple les Os de type BSD, là il faut attendre trèèèèèèèèèèèèèèès longtemps ....... wink

Desktop 1: SKP P21. Gigabyte B550M DS3H. AMD Ryzen 9 3900 @ 3,1 Ghz. Kingston FURY 64 Gb DDR4-3200. Sapphire Radeon Pulse RX 6700 XT 12Gb.
Laptop: Acer Aspire E5-573G. Intel Core i3-4005U @ 1,7 Ghz. Intel Haswell-ULT Integrated Graphics
Desktop 2: HP Compaq 6000 Pro Intel Core2 Quad Q8400 @ 2,6 Ghz. 6Gb ddr3. Geforce GT 710

Hors ligne

#8 10-02-2017 10:49:06

anonyme
Invité

Re : [resolu]installation stretch sur PC Intel KabyLake

Bonjour


journalctl -r -p err
 



-- Logs begin at Thu 2017-02-09 01:34:31 CET, end at Fri 2017-02-10 10:42:35 CET. --
févr. 09 07:09:41 kabylake1 kernel: sd 6:0:0:0: [sdc] Assuming drive cache: write through
févr. 09 07:09:41 kabylake1 kernel: sd 6:0:0:0: [sdc] No Caching mode page found
 


aucune erreur ça tourne bien  smile

c'est plus des problèmes externes que la faute de debian roll

#9 10-02-2017 19:25:04

yoshi
Membre
Lieu : Normandie
Distrib. : LMDE 6 Faye
Noyau : 6.6.5-1-liquorix-amd64
(G)UI : Cinnamon 5.8.4
Inscription : 05-03-2014

Re : [resolu]installation stretch sur PC Intel KabyLake

Nickel ! Et tant mieux, wink

Chez moi, le problème du kernel 4.9 est résolu aussi. J'ai actuellement le 4.9.8 et tout fonctionne bien.

Desktop 1: SKP P21. Gigabyte B550M DS3H. AMD Ryzen 9 3900 @ 3,1 Ghz. Kingston FURY 64 Gb DDR4-3200. Sapphire Radeon Pulse RX 6700 XT 12Gb.
Laptop: Acer Aspire E5-573G. Intel Core i3-4005U @ 1,7 Ghz. Intel Haswell-ULT Integrated Graphics
Desktop 2: HP Compaq 6000 Pro Intel Core2 Quad Q8400 @ 2,6 Ghz. 6Gb ddr3. Geforce GT 710

Hors ligne

Pied de page des forums