jean-luc@KuJL:~$ sudo smartctl -a /dev/sdc1
[sudo] Mot de passe de jean-luc :
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-13-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus
Device Model: ST3160023AS
Serial Number: 5MT062ZZ
Firmware Version: 8.12
User Capacity: 160000000000 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-6 T13/1410D revision 2
Local Time is: Sun Dec 20 13:43:10 2020 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 94) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 058 049 006 Pre-fail Always - 114412494
3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1893
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 088 060 030 Pre-fail Always - 720561431
9 Power_On_Hours 0x0032 055 055 000 Old_age Always - 39744
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2165
194 Temperature_Celsius 0x0022 029 047 000 Old_age Always - 29 (0 12 0 0 0)
195 Hardware_ECC_Recovered 0x001a 058 049 000 Old_age Always - 114412494
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 198 000 Old_age Always - 7
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 64 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 64 occurred at disk power-on lifetime: 37237 hours (1551 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 06 4e 00 00 e0 Error: UNC 6 sectors at LBA = 0x0000004e = 78
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 00 00 e0 00 00:08:43.261 READ DMA EXT
25 00 68 88 4f 73 e0 00 00:08:43.208 READ DMA EXT
25 00 80 00 4f 73 e0 00 00:08:43.145 READ DMA EXT
25 00 08 f0 4e 73 e0 00 00:08:43.138 READ DMA EXT
25 00 f0 00 4e 73 e0 00 00:08:43.007 READ DMA EXT
Error 63 occurred at disk power-on lifetime: 37237 hours (1551 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 06 4e 00 00 e0 Error: UNC 6 sectors at LBA = 0x0000004e = 78
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 00 00 e0 00 00:08:31.108 READ DMA EXT
25 00 08 48 00 00 e0 00 00:08:31.089 READ DMA EXT
25 00 10 f0 4d 73 e0 00 00:08:31.077 READ DMA EXT
25 00 f0 00 4d 73 e0 00 00:08:30.956 READ DMA EXT
25 00 10 f0 4c 73 e0 00 00:08:30.945 READ DMA EXT
Error 62 occurred at disk power-on lifetime: 37237 hours (1551 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 06 4e 00 00 e0 Error: UNC 6 sectors at LBA = 0x0000004e = 78
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 00 00 e0 00 00:08:31.108 READ DMA EXT
25 00 10 f0 4d 73 e0 00 00:08:31.089 READ DMA EXT
25 00 f0 00 4d 73 e0 00 00:08:31.077 READ DMA EXT
25 00 10 f0 4c 73 e0 00 00:08:30.956 READ DMA EXT
25 00 f0 00 4c 73 e0 00 00:08:30.945 READ DMA EXT
Error 61 occurred at disk power-on lifetime: 37237 hours (1551 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 06 4e 00 00 e0 Error: UNC 6 sectors at LBA = 0x0000004e = 78
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 00 00 e0 00 00:08:31.108 READ DMA EXT
25 00 08 78 00 00 e0 00 00:08:31.089 READ DMA EXT
25 00 08 98 14 fc e0 00 00:08:31.077 READ DMA EXT
25 00 08 40 00 00 e0 00 00:08:30.956 READ DMA EXT
25 00 08 38 00 00 e0 00 00:08:30.945 READ DMA EXT
Error 60 occurred at disk power-on lifetime: 37237 hours (1551 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 2e 4e 00 00 e0 Error: UNC 46 sectors at LBA = 0x0000004e = 78
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 20 00 00 e0 00 00:08:26.674 READ DMA EXT
25 00 20 00 00 00 e0 00 00:08:26.667 READ DMA EXT
25 00 90 80 18 fc e0 00 00:08:26.661 READ DMA EXT
25 00 38 40 18 fc e0 00 00:08:26.655 READ DMA EXT
25 00 18 20 18 fc e0 00 00:08:26.639 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short captive Completed without error 00% 4982 -
# 2 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
jean-luc@KuJL:~$