Vous n'êtes pas identifié(e).
servers: 80.67.169.12 37.187.16.17 80.67.169.40
servers: fd0f:ee:b0::1
c'est la 2°ligne qui me pose question
d'après ce que j'ai pu glaner sur le net cela correspondrait à l'IPv6 mais si je vais sur la configuration de la freebox -->configuration IPv6-->Adresse IPv6 lien local:
fe80::224:d4ff:feaf:fc4c donc cela ne correspond pas.
à quoi correspond cette adresse?
Thierry
Dans quelle section ? [ifupdown] ?
oui, voici le contenu de :
[main]
plugins=ifupdown,keyfile
[ifupdown]
managed=true
et si je n'ai pas répondu plus tôt, c'est que j'ai remis "managed=false" et depuis, après de nombreux redémarrages, cette adresse supplémentaire dhcp n’apparaît plus. sans avoir fait d'autres modifications ; je ne comprendrais vraiment jamais rien à l'informatique
dans tous les cas, merci
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: enp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether c8:1f:66:2f:e0:2e brd ff:ff:ff:ff:ff:ff
inet 192.168.5.170/24 brd 192.168.5.255 scope global noprefixroute enp3s0
valid_lft forever preferred_lft forever
inet 192.168.5.59/24 brd 192.168.5.255 scope global secondary dynamic noprefixroute enp3s0
valid_lft 84730sec preferred_lft 84730sec
inet6 fe80::f97:67c6:8d9e:a698/64 scope link noprefixroute
valid_lft forever preferred_lft forever
3: enp4s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN group default qlen 1000
link/ether 7c:8b:ca:00:b4:66 brd ff:ff:ff:ff:ff:ff
4: wlxd037457542c8: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default qlen 1000
link/ether d0:37:45:75:42:c8 brd ff:ff:ff:ff:ff:ff
et donc avec enp3s0 : en inet 192.168.5.170/24
et inet 192.168.5.59/24
enp3s0: connecté à Connexion filaire 2
"Realtek RTL8111/8168/8411"
ethernet (r8169), C8:1F:66:2F:E0:2E, hw, mtu 1500
ip4 par défaut
inet4 192.168.5.59/24
inet4 192.168.5.170/24
route4 192.168.5.0/24 metric 100
route4 default via 192.168.5.1 metric 100
route4 192.168.5.0/24 metric 100
inet6 fe80::f97:67c6:8d9e:a698/64
route6 fe80::/64 metric 1024
lo: connecté (en externe) à lo
"lo"
loopback (unknown), 00:00:00:00:00:00, sw, mtu 65536
inet4 127.0.0.1/8
inet6 ::1/128
enp4s0: indisponible
"Realtek RTL8111/8168/8411"
ethernet (r8169), 7C:8B:CA:00:B4:66, hw, mtu 1500
wlxd037457542c8: indisponible
"Realtek RTL8188EUS"
wifi (r8188eu), D0:37:45:75:42:C8, sw désactivé, hw, mtu 1500
[connection]
id=Connexion filaire 2
uuid=680045b4-fdd3-35c0-8e99-34600be3cb9a
type=ethernet
autoconnect-priority=-999
interface-name=enp3s0
timestamp=1698915424
[ethernet]
[ipv4]
address1=192.168.5.170/24,192.168.5.1
method=auto
[ipv6]
addr-gen-mode=stable-privacy
method=auto
[proxy]
d'avance merci
thierry
en remettant le même mot de passe et ça marche,
bizarre
merci
et synaptic s'ouvre
ping: unknown host
lo: connecté (en externe) à lo
"lo"
loopback (unknown), 00:00:00:00:00:00, sw, mtu 65536
inet4 127.0.0.1/8
inet6 ::1/128
eth0: non-géré
"Marvell 88E8040"
ethernet (sky2), 00:13:77:B2:90:9F, hw, mtu 1500
wlan0: non-géré
"Qualcomm Atheros AR242x / AR542x"
wifi (ath5k), 00:21:63:A3:D0:B4, hw, mtu 1500
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 13 bytes 1978 (1.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
il fallait supprimer le fichier /etc/resolv.conf généré par Connection Manager
pas de fichier resolv.conf, seulement un dossier et pas ce fichier à l'intérieur
NetworkManager est déjà en cours d'exécution (pid 15059=
et
j'avais installé network-manager-gnome en même temps que network manager
i A sysv-rc - mécanisme de changement de niveau d'exécution à la System-V
i sysv-rc-conf - Outil de configuration de niveau d'exécution (runlevel) SysV init pour le terminal
i sysvinit-core - System-V-like init
i sysvinit-utils - utilitaires de type System V
RTNETLINK answers: File exist
RTNETLINK answers: File exist
PING 192.168.5.1 (192.168.5.1): 56 data bytes
64 bytes from 192.168.5.1: icmp_seq=0 ttl=64 time=1,732 ms
64 bytes from 192.168.5.1: icmp_seq=1 ttl=64 time=0,820 ms
64 bytes from 192.168.5.1: icmp_seq=2 ttl=64 time=0,827 ms
64 bytes from 192.168.5.1: icmp_seq=3 ttl=64 time=0,890 ms
--- 192.168.5.1 ping statistics ---
4 packets transmitted, 4 packets received, 0% packet loss
round-trip min/avg/max/stddev = 0,820/1,067/1,732/0,385 ms
et:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:13:77:b2:90:9f brd ff:ff:ff:ff:ff:ff
inet 192.168.5.53/24 brd 192.168.5.255 scope global dynamic eth0
valid_lft 85484sec preferred_lft 85484sec
inet6 fe80::213:77ff:feb2:909f/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:21:63:a3:d0:b4 brd ff:ff:ff:ff:ff:ff
et pourtant le navigateur seamonkey (installé par défaut) ne donne aucun résultat (address no found)
configuring network interface...done
et de:
Running /etc/init.d/networking restart is deprecated because it may not re-enable some interfaces ... (warning).
Reconfiguring network interfaces...Killed old client process
Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:13:77:b2:90:9f
Sending on LPF/eth0/00:13:77:b2:90:9f
Sending on Socket/fallback
DHCPRELEASE of 192.168.5.53 on eth0 to 192.168.5.1 port 67
Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:13:77:b2:90:9f
Sending on LPF/eth0/00:13:77:b2:90:9f
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
DHCPOFFER of 192.168.5.53 from 192.168.5.1
DHCPREQUEST for 192.168.5.53 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.5.53 from 192.168.5.1
bound to 192.168.5.53 -- renewal in 33898 seconds.
done.
systemd:
Installé : (aucun)
candidat : (aucun)
pas moyen de rajouter une connexion, tout est grisé
et en plus cela se corse car:
remplacé par:
donc si vous avez des idées pour m'aider à résoudre ce problème, d'avance merci
Tu as essayé d'appuyer sur la touche <Tabulation> pour faire bouger le focus ?
gloups c'était ça, merci
Configuration de virtualbox-ext-pack ├──────────────────┐
│ │
│ .......................................courts of San Francisco or Santa Clara counties in California in any
│ dispute arising out of or relating to this Agreement. Upon 45 days
│ written notice, Oracle may audit your use of the Product to confirm that
│ you are in compliance with the terms of this Agreement. You agree to
│ cooperate with Oracle's audit and provide reasonable assistance and
│ access to information. Any such audit shall not unreasonably interfere
│ with your normal business operations. You agree to pay within 30 days of
│ written notification any fees applicable to your unlicensed use of the
│ Product. You agree that Oracle shall not be responsible for any of your
│ costs incurred in cooperating with the audit. If a legal action or
│ proceeding is commenced by either party in connection with the
│ enforcement of this Agreement, the prevailing party shall be entitled to
│ its costs and attorneys' fees actually incurred in connection with such
│ action or proceeding.
│
│ <Ok>
ps: j'ai mis cette page en "citation" car je ne sais plus comment joindre une photo
je ne peux cliquer sur "ok" pas plus avec la touche entrée, même après avoir complétement déroulé la page