ça a l'air OK non ?
# smartctl --all /dev/sdc
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.16.0-4-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD103SJ
Serial Number: S246J90Z711161
LU WWN Device Id: 5 0024e9 202dd685c
Firmware Version: 1AJ10001
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri May 29 15:48:18 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Warning! SMART Attribute Thresholds Structure error: invalid SMART checksum.
=== START OF READ SMART DATA SECTION ===
SMART Status command failed: scsi error aborted command
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9540) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 159) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 50
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 072 070 025 Pre-fail Always - 8766
4 Start_Stop_Count 0x0032 095 095 000 Old_age Always - 5708
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 16214
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 095 095 000 Old_age Always - 5704
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 1
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 063 054 000 Old_age Always - 37 (Min/Max 15/47)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 --- Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 099 099 --- Old_age Always - 1036
200 Multi_Zone_Error_Rate 0x002a 100 100 --- Old_age Always - 185
223 Load_Retry_Count 0x0032 252 252 --- Old_age Always - 0
225 Load_Cycle_Count 0x0032 100 100 --- Old_age Always - 5717
SMART Error Log Version: 1
ATA Error Count: 1036 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1036 occurred at disk power-on lifetime: 16214 hours (675 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 4f c2 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d1 01 01 4f c2 00 08 00:00:04.586 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
b0 d1 01 01 4f c2 00 08 00:00:04.586 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
b0 d0 01 00 4f c2 00 08 00:00:04.586 SMART READ DATA
ec 00 01 00 00 00 00 08 00:00:04.586 IDENTIFY DEVICE
ec 00 01 00 00 00 00 08 00:00:04.586 IDENTIFY DEVICE
Error 1035 occurred at disk power-on lifetime: 16094 hours (670 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 4f c2 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d1 01 00 4f c2 00 08 00:00:07.362 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
b0 d1 01 00 4f c2 00 08 00:00:07.362 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
e5 00 00 00 00 00 00 08 00:00:07.362 CHECK POWER MODE
ec 00 01 00 00 00 00 08 00:00:07.362 IDENTIFY DEVICE
b0 da 00 00 4f c2 00 08 00:00:05.563 SMART RETURN STATUS
Error 1034 occurred at disk power-on lifetime: 16073 hours (669 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec ff 01 01 00 00 e0 00 00:00:00.020 IDENTIFY DEVICE
a1 ff 01 01 00 00 e0 00 00:00:00.020 IDENTIFY PACKET DEVICE
Error 1033 occurred at disk power-on lifetime: 15992 hours (666 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 4f c2 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d0 01 00 4f c2 00 08 00:00:10.977 SMART READ DATA
b0 d0 01 00 4f c2 00 08 00:00:10.977 SMART READ DATA
b0 d1 01 00 4f c2 00 08 00:00:10.977 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
e5 00 00 00 00 00 00 08 00:00:10.977 CHECK POWER MODE
ec 00 01 00 00 00 00 08 00:00:10.977 IDENTIFY DEVICE
Error 1032 occurred at disk power-on lifetime: 15984 hours (666 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:20.445 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 08 00:00:20.445 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:00:20.445 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 08 00:00:20.445 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 00:00:20.445 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 16212 -
# 2 Short offline Completed without error 00% 16212 -
# 3 Short offline Completed without error 00% 11698 -
# 4 Short offline Completed without error 00% 11698 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
mon ancien pseudo : bartaba