logo Debian Debian Debian-France Debian-Facile Debian-fr.org Forum-Debian.fr Debian ? Communautés logo inclusivité

Debian-facile

Bienvenue sur Debian-Facile, site d'aide pour les nouveaux utilisateurs de Debian.

Vous n'êtes pas identifié(e).

#1 Re : Installation et migration » Paramétrage seconde interface WiFi RLT8188eus » 30-06-2020 13:38:10

Scubadiver
Bon personne n'a d'idées pour faire fonctionner cette clé en monitoring?

#2 Re : Installation et migration » usb 5-1: can't set config #1, error -71 » 30-06-2020 13:36:15

Scubadiver
Personne ne sait a quoi ça correspond sur ce forum?

#3 Installation et migration » usb 5-1: can't set config #1, error -71 » 10-06-2020 23:50:18

Scubadiver
Réponses : 2
Je n'arrive pas a trouver a quoi corresponds l'erreur 71 qui est annoncé dans le lot kernel après insertion d'un périphérique usb.

Quelqu'un sait ou cela est documenté?

Merci d'avance

#4 Re : Installation et migration » Paramétrage seconde interface WiFi RLT8188eus » 10-06-2020 18:03:36

Scubadiver
Bon ce driver fonctionne effectivement mais certaines fonction comme le mode monitor ne sont pas disponibles...

je dois revenir sur cette version : https://github.com/aircrack-ng/rtl8188eus

Mais après installation (cette fois ci je l'ai faite avec le dkms-install.sh) l'interface wlan1 ne se monte pas...

#5 Re : Installation et migration » Paramétrage seconde interface WiFi RLT8188eus » 09-06-2020 17:46:52

Scubadiver
Ca fait plaisir de lire çà :

iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11  ESSID:"Dephdiver_Timeport"  
          Mode:Managed  Frequency:5.745 GHz  Access Point: F0:99:BF:0E:2C:0D  
          Bit Rate=40.5 Mb/s   Tx-Power=15 dBm  
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=70/70  Signal level=-40 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:25   Missed beacon:0

wlan1     unassociated  Nickname:"<WIFI@REALTEK>"
          Mode:Managed  Frequency=2.412 GHz  Access Point: Not-Associated  
          Sensitivity:0/0  
          Retry:off   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=0/100  Signal level=0 dBm  Noise level=0 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
 


ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 00:1f:16:a4:8c:6f brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.17/24 brd 192.168.1.255 scope global dynamic noprefixroute eth0
       valid_lft 31535805sec preferred_lft 31535805sec
    inet6 fe80::21f:16ff:fea4:8c6f/64 scope link noprefixroute
       valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 00:22:fb:6f:79:64 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.18/24 brd 192.168.1.255 scope global dynamic noprefixroute wlan0
       valid_lft 31535813sec preferred_lft 31535813sec
    inet6 fe80::944d:9e40:f8ef:10ec/64 scope link noprefixroute
       valid_lft forever preferred_lft forever
6: wlan1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
    link/ether 00:e0:26:30:2e:3b brd ff:ff:ff:ff:ff:ff



dkms status
realtek-rtl8188eus, 5.3.9~git20200316, 5.6.0-kali2-amd64, x86_64: installed
rtl8188fu, 1.0, 5.6.0-kali2-amd64, x86_64: installed



Merci beaucoup Beta-Pictoris de ton aide et oui èfpé il s'est installé sans problème.

#7 Re : Installation et migration » Paramétrage seconde interface WiFi RLT8188eus » 08-06-2020 18:45:41

Scubadiver
J'ai des erreurs...
J'avais pas vu le message de Beta-Pictoris de downgrader le kernel!...

cc1: some warnings being treated as errors
make[3]: *** [/usr/src/linux-headers-5.6.0-kali2-common/scripts/Makefile.build:273: /var/lib/dkms/rtl8188fu/1.0/build/os_dep/linux/rtw_proc.o] Error 1
make[2]: *** [/usr/src/linux-headers-5.6.0-kali2-common/Makefile:1704: /var/lib/dkms/rtl8188fu/1.0/build] Error 2
make[1]: *** [/usr/src/linux-headers-5.6.0-kali2-common/Makefile:180: sub-make] Error 2
make[1] : on quitte le répertoire « /usr/src/linux-headers-5.6.0-kali2-amd64 »
make: *** [Makefile:470: modules] Error 2
 


Je désinstallation alors,
Ya pas une solution pour un 5.6? le driver que l'avais était pour ce kernel... pourquoi il ne fonctionne pas?

#8 Re : Installation et migration » Paramétrage seconde interface WiFi RLT8188eus » 08-06-2020 17:31:15

Scubadiver
non effectivement je ne connaissait pas...
Voici le résultat

modinfo -F alias {r,}8188eu | grep 0BDA
usb:v0BDApFFEFd*dc*dsc*dp*ic*isc*ip*in*
usb:v0BDAp0179d*dc*dsc*dp*ic*isc*ip*in*
usb:v0BDAp8179d*dc*dsc*dp*ic*isc*ip*in*
usb:v0BDAp8179d*dc*dsc*dp*ic*isc*ip*in*
usb:v0BDAp0179d*dc*dsc*dp*ic*isc*ip*in*
usb:v0BDAp8179d*dc*dsc*dp*ic*isc*ip*in*



C'est grave docteur? On peut arriver a le faire prendre en charge?

#9 Re : Installation et migration » Paramétrage seconde interface WiFi RLT8188eus » 08-06-2020 14:14:26

Scubadiver

chalu a écrit :

En lisant ton post, je vois que tu ne parles pas de la version du noyau. J'imagine qu'il en faut un récent, peut-être 5.x ?


Oui noyau 5.6

Pour le profil c'est fait wink

#10 Installation et migration » Paramétrage seconde interface WiFi RLT8188eus » 08-06-2020 11:44:37

Scubadiver
Réponses : 13
Bonjour à tous,

Je me trouve actuellement dans une impasse. J'ai besoin de configurer une seconde interface WiFi (Clé USB RLT8188eus) afin de pouvoir brancher une antenne externe.

lsusb
Bus 004 Device 004: ID 04f2:b160 Chicony Electronics Co., Ltd CNF9113
[b]Bus 004 Device 009: ID 0bda:f179 Realtek Semiconductor Corp. 802.11n[/b]
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 25a7:fa61 Compx 2.4G Receiver
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
 



Ma carte WiFi principale fonctionnant parfaitement en wlan0

iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11  ESSID:"Dephdiver_Timeport"  
          Mode:Managed  Frequency:2.462 GHz  Access Point: 10:9A:DD:8A:59:91  
          Bit Rate=65 Mb/s   Tx-Power=15 dBm  
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Power Management:off
          Link Quality=70/70  Signal level=-32 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:2   Missed beacon:0

ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 00:1f:16:a4:8c:6f brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.17/24 brd 192.168.1.255 scope global dynamic noprefixroute eth0
       valid_lft 31477203sec preferred_lft 31477203sec
    inet6 fe80::21f:16ff:fea4:8c6f/64 scope link noprefixroute
       valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 00:22:fb:6f:79:64 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.18/24 brd 192.168.1.255 scope global dynamic noprefixroute wlan0
       valid_lft 31477236sec preferred_lft 31477236sec
    inet6 fe80::944d:9e40:f8ef:10ec/64 scope link noprefixroute
       valid_lft forever preferred_lft forever
 



La clé n'étant pas reconnue, j'ai installé les derniers drivers après backlist des drivers anciens:

echo "blacklist r8188eu" > /etc/modprobe.d/realtek.conf
apt-get update
apt-get install realtek-rtl8188eus-dkms



A priori le driver semble bien installé mais aucun accès à la clé...

apt-cache search realtek
flashrom - Identify, read, write, erase, and verify BIOS/ROM/flash chips
librtlsdr-dev - Software defined radio receiver for Realtek RTL2832U (development)
librtlsdr0 - Software defined radio receiver for Realtek RTL2832U (library)
nictools-pci - Diagnostic tools for many PCI Ethernet cards
python3-rtlsdr - Python wrapper for librtlsdr (Python3 package)
rtl-sdr - Software defined radio receiver for Realtek RTL2832U (tools)
soapysdr-module-rtlsdr - RTL-SDR device support for SoapySDR (default version)
soapysdr0.7-module-rtlsdr - RTL-SDR device support for SoapySDR
firmware-realtek - Binary firmware for Realtek wired/wifi/BT adapters
r8168-dkms - dkms source for the r8168 network driver
realtek-rtl8188eus-dkms - Realtek RTL8188EUS driver in DKMS format
realtek-rtl88xxau-dkms - Realtek RTL88xxAU driver in DKMS format



Le firmware n'est pas chargé :

dmesg | grep firmware
[   21.507133] platform regulatory.0: firmware: direct-loading firmware regulatory.db
[   21.555088] platform regulatory.0: firmware: direct-loading firmware regulatory.db.p7s
[   21.908507] iwlwifi 0000:02:00.0: firmware: direct-loading firmware iwlwifi-5000-5.ucode
[   21.908663] iwlwifi 0000:02:00.0: loaded firmware version 8.83.5.1 build 33692 5000-5.ucode op_mode iwldvm



J'ai surement oublié de faire quelque chose, avez vous une idée?

Merci d'avance

Pied de page des forums

Propulsé par FluxBB