Vous n'êtes pas identifié(e).
Pages : 1
pour pouvoir contrôler les températures. J'ai donc lancé
et répondu
partout mais en exécutant
j'ai eu une erreur de chargement (je ne l'ai pas noté), j'ai redémarré et maintenant à chaque redémarrage je vois qu'il y a une erreur qui défile.
A l'instant (donc après redémarrage) si je fait à nouveau
j'ai :
J'ai regardé https://debian-facile.org/viewtopic.php?id=9332
en exécutant
donne :
et
et
Détail de ma config matériel avec
:
Chemin matériel Périphérique Classe Description
==========================================================
system PROD00000000
/0 bus Motherboard
/0/0 memory 128KiB BIOS
/0/4 processor Intel(R) Celeron(R) M processor 1.50GHz
/0/4/a memory 32KiB L1 cache
/0/4/b memory 1MiB L2 cache
/0/1f memory 512MiB Mémoire Système
/0/1f/0 memory 256MiB DIMM SDRAM Synchrone
/0/1f/1 memory DIMMProject-Id-Version: @(#) $Id: fr.po 2151 2010-03-
/0/1f/2 memory 256MiB DIMM SDRAM Synchrone
/0/1f/3 memory DIMMProject-Id-Version: @(#) $Id: fr.po 2151 2010-03-
/0/100 bridge Mobile 915GM/PM/GMS/910GML Express Processor to DRAM
/0/100/2 display Mobile 915GM/GMS/910GML Express Graphics Controller
/0/100/1b multimedia 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition A
/0/100/1d bus 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
/0/100/1d/1 usb2 bus UHCI Host Controller
/0/100/1d/1/2 input USB Keyboard
/0/100/1d.1 bus 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
/0/100/1d.1/1 usb3 bus UHCI Host Controller
/0/100/1d.1/1/1 input USB-PS/2 Optical Mouse
/0/100/1d.2 bus 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
/0/100/1d.2/1 usb4 bus UHCI Host Controller
/0/100/1d.2/1/2 generic IRTrans USB
/0/100/1d.3 bus 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
/0/100/1d.3/1 usb5 bus UHCI Host Controller
/0/100/1d.7 bus 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Control
/0/100/1d.7/1 usb1 bus EHCI Host Controller
/0/100/1d.7/1/8 wlx00120e0ea8fe network USB2.0 WLAN
/0/100/1e bridge 82801 Mobile PCI Bridge
/0/100/1e/3 bus FW322/323 [TrueFire] 1394a Controller
/0/100/1e/5 enp1s5 network RTL8169 PCI Gigabit Ethernet Controller
/0/100/1f bridge 82801FBM (ICH6M) LPC Interface Bridge
/0/100/1f.2 storage 82801FBM (ICH6M) SATA Controller
/0/100/1f.3 bus 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller
/0/1 scsi0 storage
/0/1/0.0.0 /dev/sda disk 60GB SAMSUNG HM060II
/0/1/0.0.0/1 /dev/sda1 volume 55GiB EXT4 volume
/0/1/0.0.0/2 /dev/sda2 volume 502MiB Extended partition
/0/1/0.0.0/2/5 /dev/sda5 volume 502MiB Linux swap volume
Bonne soirée
Grégoire
Dernière modification par gregoire (28-01-2019 22:31:55)
Hors ligne
dans le fichier :
puis en éxécutant :
Maintenant en exécutant la commande
j'ai :
Que signifie les
, les voltages min et max me paraissent bizarres, et le fan3 ?
Maintenant je suis preneur pour toute solution pour optimiser le volume sonore (CF premier post).
A bientôt
Hors ligne
Pages : 1