Ne peux pas activer la wifi

Arghalion · 09-02-2020 00:08:50

Bonjours a tous!
je suis novice et j'ai installé debian Buster aujourd'hui même en dual boot
Je ne peux pas activer la wifi elle reste éteinte
apres des heures de recherches je suis perdu
Je viens de désactiver le secure boot

ip a

3: wlp7s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

    link/ether f8:a2:d6:c6:c3:85 brd ff:ff:ff:ff:ff:ff

rfkill

  ID TYPE      DEVICE                SOFT     HARD

 0 wlan      ideapad_wlan      débloqué   bloqué

 1 bluetooth ideapad_bluetooth débloqué   bloqué

 2 bluetooth hci0              débloqué débloqué

 3 wlan      phy0              débloqué débloqué

ca doit venir d'ici mais j'avoue ne pas m'y connaître, l’installation des firmware a pourtant réussi

dmesg | grep firmware

 [   12.258743] ath10k_pci 0000:07:00.0: firmware: failed to load ath10k/pre-cal-pci-0000:07:00.0.bin (-2)

[   12.258867] ath10k_pci 0000:07:00.0: firmware: failed to load ath10k/cal-pci-0000:07:00.0.bin (-2)

[   12.305908] ath10k_pci 0000:07:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/firmware-6.bin

[   12.307415] ath10k_pci 0000:07:00.0: firmware ver WLAN.TF.2.1-00021-QCARMSWP-1 api 6 features wowlan,ignore-otp crc32 42e41877

[   12.474950] ath10k_pci 0000:07:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/board-2.bin

je vous remercie pour votre temps

Dernière modification par Arghalion (09-02-2020 00:20:46)

Arghalion · 09-02-2020 00:13:25

Et j'ai le même pb avec un clé wifi, la carte est présente mais inutilisable

ip a

3: wlp7s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

    link/ether f8:a2:d6:c6:c3:85 brd ff:ff:ff:ff:ff:ff

4: wlx100d7fbd384d: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

    link/ether 10:0d:7f:bd:38:4d brd ff:ff:ff:ff:ff:ff

otyugh · 09-02-2020 00:20:43

Tu peux essayer mon tuto là-dessus si tu y arrives ? Je suis curieux de voir si quelqu'un peut se débrouiller lui-même avec.

https://debian-facile.org/doc:materiel: … privateurs

Arghalion · 09-02-2020 00:32:11

Beta testing terminé

alors oui j'ai tout fait mais ça marche tout de même pas, il me précise que le firmware qui est nécessaire est déjà installé

Cependant j'ai quand même appris a utiliser apt search

otyugh · 09-02-2020 00:43:43

Tu peux donner donner le retour des commandes ici ? Du lspci et de quel paquet tu as essayé d'installer. Je ne peux pas deviner d'où je suis.

Arghalion · 09-02-2020 00:49:37

  apt-cache policy firmware-atheros 

 firmware-atheros:

  Installé : 20190114-2

  Candidat : 20190114-2

 Table de version :

 *** 20190114-2 500

        500 http://httpredir.debian.org/debian buster/non-free amd64 Packages

        500 http://deb.debian.org/debian buster/non-free amd64 Packages

        100 /var/lib/dpkg/status

et

lspci

  Network controller: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter (rev 31) 

je te remercie de ta rapidité

lagrenouille · 09-02-2020 00:52:17

donc tu as installé :

wpasupplicant wireless-tools firmware-atheros firmware-iwlwifi ?

c'est ça ?

Dernière modification par lagrenouille (09-02-2020 00:56:15)

Arghalion · 09-02-2020 00:55:37

lagrenouille a écrit :

donc tu as installé :

wpasupplicant wireless-tools firmware-atheros firmware-iwlwifi ?

c'edst ça ?

absolument oui

lagrenouille · 09-02-2020 01:05:12

explique un peu plus, tu es derrière une box ? ta connexion câblée avec un rj454 fonctionne
si box, tu as mis ton mot de passe ? etc....

Arghalion · 09-02-2020 01:11:05

la connexion cablée marche bien oui, en revanche quand je clique sur le logo en haut a droite (gnome) sur le symbole de la wifi, la wifi est dite "éteinte" et pas moyen de l'activer le bouton "activer le WI-FI" ne change rien

lagrenouille · 09-02-2020 01:12:48

je connais pas gnome, mais clique gauche, ou droit , propriété ou configuration, tu as pas ça ?

Dernière modification par lagrenouille (09-02-2020 01:13:06)

Arghalion · 09-02-2020 01:15:30

dans les paramètres de la wifi il m'annonce "aucun adaptateur wifi trouvé"

otyugh · 09-02-2020 01:16:05

Ahm.

apt show firmware-atheros | grep QCA9377

  * Qualcomm Atheros QCA9377 rev 1.0 board configuration, version 1

    (ath10k/QCA9377/hw1.0/board.bin)

  * Qualcomm Atheros QCA9377 rev 1.0 board configuration, version 2

    (ath10k/QCA9377/hw1.0/board-2.bin)

  * Qualcomm Atheros QCA9377 rev 1.0 firmware, version

    WLAN.TF.1.0-00267-1 (ath10k/QCA9377/hw1.0/firmware-5.bin)

  * Qualcomm Atheros QCA9377 rev 1.0 firmware, version

    WLAN.TF.2.1-00021-QCARMSWP-1 (ath10k/QCA9377/hw1.0/firmware-6.bin)

Je vois du "rev 1.0" de partout, et dans ton lspci, tu as "rev 31". J'y connais rien mais mon pari va être que "c'est pas supporté nativement par debian".

Quelqu'un a eu le même souci sous Ubuntu et l'a résolu, ça devrait marcher ?
https://askubuntu.com/questions/994555/ … stallation

Arghalion · 09-02-2020 01:49:59

raté encore, je vais peut etre recommencer l'installation demain avec les fireware prets sur la clé bootable
sinon je peux acheter une clé wifi du coup?

j'ai les yeux qui se ferment je vais y aller
en tout cas merci beaucoup

Dernière modification par Arghalion (09-02-2020 01:50:31)

otyugh · 09-02-2020 02:11:38

Il y a certainement une solution ; mais je suis définitvement pas le plus à l'aise du forum avec les questions de fimware, j'espère qu'une de ces personnes passera.

sinon je peux acheter une clé wifi du coup?

Certainement. Par contre je ferai une rapide recherche avec le modèle avant de faire mon achat, on ne sait jamais (je m'en suis toujours sortit mais bon, tu es la preuve que ce n'est pas toujours si simple)

Dernière modification par otyugh (09-02-2020 02:14:54)

chalu · 09-02-2020 08:25:33

Bonjour,
Post #1 le retour de rfkil

 ID TYPE      DEVICE                SOFT     HARD

 0 wlan      ideapad_wlan      débloqué   bloqué

 1 bluetooth ideapad_bluetooth débloqué   bloqué

 2 bluetooth hci0              débloqué débloqué

 3 wlan      phy0              débloqué débloqué

indique une interface bloquée matériellement (je ne sais pas si ça se dit ) il faudrait voir s’il y a un bouton ou une combinaison de touches ou dans le BIOS pour la débloquer.

Dans le post 2, on voit la clé

 3: wlp7s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

    link/ether f8:a2:d6:c6:c3:85 brd ff:ff:ff:ff:ff:ff

4: wlx100d7fbd384d: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

    link/ether 10:0d:7f:bd:38:4d brd ff:ff:ff:ff:ff:ff

Elle se nomme wlx donc pourrait bien être concernée par ceci
https://debian-facile.org/viewtopic.php?id=21137

Édit

pas moyen de l'activer le bouton "activer le WI-FI" ne change rien

C’est un bouton sur le clavier ? Tu es en dual boot avec Windows ? Le secureboot est-il désactivé ? Il me semble me souvenir d’un fil où le désactiver à résolu le problème mais je n’ai plus le temps de chercher ce matin.

Arghalion · 09-02-2020 10:07:50

C’est un bouton sur le clavier ? Tu es en dual boot avec Windows ? Le secureboot est-il désactivé ? Il me semble me souvenir d’un fil où le désactiver à résolu le problème mais je n’ai plus le temps de chercher ce matin.

c'est un bouton, le "turn off" (évidemment c'est plutot "turn on" pour moii)

je suis en dual boot et je suis allé désactivé le secureboot en effet

c'est interessant j'ai fait les manip du tuto pour une clé wifi le probleme est le meme: (la clé wifi est aussi inactivable par le bouton turn on)

nmcli device

DEVICE       TYPE      STATE         CONNECTION         

enp8s0       ethernet  connecté      Wired connection 1 

wlp0s20f0u3  wifi      indisponible  --                  #ma clé WIFI               

wlp7s0       wifi      indisponible  --                  #ma carte Artheros        

lo           loopback  non-géré      --

lagrenouille · 09-02-2020 10:17:58

ton /etc/network/interfaces ne doit contenir que ceci
tu as mis autre chose ?

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

source /etc/network/interfaces.d/*

# The loopback network interface
auto lo
iface lo inet loopback

systemctl restart network-manager.service
systenctl restart networking.service

Dernière modification par lagrenouille (09-02-2020 10:27:04)

Arghalion · 09-02-2020 10:30:51

interfaces est exactement comme tu le décris

LaFouine · 09-02-2020 12:11:19

voui

bon si l'adaptateur est pas reconnu il te faut être absolument sure que : le module ou en dur c'est bien charger
un petit retour de

lsmod -vvv

lspci -vvv

demsg

uname -a

il peux être pressent mai avoir "planter" donc faut fouiner un peux, aux besoins un kernel plus rescent peux etre ?

Beta-Pictoris · 09-02-2020 12:36:50

Arghalion a écrit :

C’est un bouton sur le clavier ? Tu es en dual boot avec Windows ? Le secureboot est-il désactivé ? Il me semble me souvenir d’un fil où le désactiver à résolu le problème mais je n’ai plus le temps de chercher ce matin.

c'est un bouton, le "turn off" (évidemment c'est plutot "turn on" pour moii)

Arghalion, peux tu donner la référence exacte de ta machine (un lenovo ideapad ?).

Retire ta clé wifi usb et blackliste le module ideapad_laptop :

echo 'blacklist ideapad_laptop' > /etc/modprobe.d/ideapad.conf

Puis reboote ta machine.

Dernière modification par Beta-Pictoris (09-02-2020 12:37:23)

Arghalion · 09-02-2020 12:39:35

alors ca va etre long ^^'

lsmod -vvv

Usage: lsmod

lspci -vvv

00:00.0 Host bridge: Intel Corporation 8th Gen Core 4-core Processor Host Bridge/DRAM Registers [Coffee Lake H] (rev 07)

  Subsystem: Lenovo 8th Gen Core 4-core Processor Host Bridge/DRAM Registers [Coffee Lake H]

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

  Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-

  Latency: 0

  Capabilities: [e0] Vendor Specific Information: Len=10 <?>

  Kernel driver in use: skl_uncore

00:01.0 PCI bridge: Intel Corporation Skylake PCIe Controller (x16) (rev 07) (prog-if 00 [Normal decode])

  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 122

  Bus: primary=00, secondary=01, subordinate=05, sec-latency=0

  I/O behind bridge: 00004000-00004fff

  Memory behind bridge: a3000000-a40fffff

  Prefetchable memory behind bridge: 0000000090000000-00000000a1ffffff

  Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

  BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-

    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

  Capabilities: [88] Subsystem: Lenovo Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor PCIe Controller (x16)

  Capabilities: [80] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-

    Address: fee00238  Data: 0000

  Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00

    DevCap: MaxPayload 256 bytes, PhantFunc 0

      ExtTag- RBE+

    DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

      MaxPayload 256 bytes, MaxReadReq 128 bytes

    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-

    LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <256ns, L1 <8us

      ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+

    LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+

      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

    LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+

    SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-

      Slot #1, PowerLimit 75.000W; Interlock- NoCompl+

    SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-

      Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

    SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

      Changed: MRL- PresDet+ LinkState-

    RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-

    RootCap: CRSVisible-

    RootSta: PME ReqID 0000, PMEStatus- PMEPending-

    DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd-

    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd-

    LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-

       Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

       Compliance De-emphasis: -6dB

    LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete+, EqualizationPhase1+

       EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-

  Capabilities: [100 v1] Virtual Channel

    Caps: LPEVC=0 RefClk=100ns PATEntryBits=1

    Arb:  Fixed- WRR32- WRR64- WRR128-

    Ctrl: ArbSelect=Fixed

    Status: InProgress-

    VC0:  Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-

      Arb:  Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-

      Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff

      Status: NegoPending- InProgress-

  Capabilities: [140 v1] Root Complex Link

    Desc: PortNumber=02 ComponentID=01 EltType=Config

    Link0:  Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+

      Addr: 00000000fed19000

  Capabilities: [d94 v1] #19

  Kernel driver in use: pcieport

00:02.0 VGA compatible controller: Intel Corporation UHD Graphics 630 (Mobile) (prog-if 00 [VGA controller])

  Subsystem: Lenovo UHD Graphics 630 (Mobile)

  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 130

  Region 0: Memory at a2000000 (64-bit, non-prefetchable) [size=16M]

  Region 2: Memory at b0000000 (64-bit, prefetchable) [size=256M]

  Region 4: I/O ports at 5000 [size=64]

  [virtual] Expansion ROM at 000c0000 [disabled] [size=128K]

  Capabilities: [40] Vendor Specific Information: Len=0c <?>

  Capabilities: [70] Express (v2) Root Complex Integrated Endpoint, MSI 00

    DevCap: MaxPayload 128 bytes, PhantFunc 0

      ExtTag- RBE+

    DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

      MaxPayload 128 bytes, MaxReadReq 128 bytes

    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-

    DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported

    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled

  Capabilities: [ac] MSI: Enable+ Count=1/1 Maskable- 64bit-

    Address: fee00018  Data: 0000

  Capabilities: [d0] Power Management version 2

    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

    Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [100 v1] Process Address Space ID (PASID)

    PASIDCap: Exec- Priv-, Max PASID Width: 14

    PASIDCtl: Enable- Exec- Priv-

  Capabilities: [200 v1] Address Translation Service (ATS)

    ATSCap: Invalidate Queue Depth: 00

    ATSCtl: Enable-, Smallest Translation Unit: 00

  Capabilities: [300 v1] Page Request Interface (PRI)

    PRICtl: Enable- Reset-

    PRISta: RF- UPRGI- Stopped+

    Page Request Capacity: 00008000, Page Request Allocation: 00000000

  Kernel driver in use: i915

  Kernel modules: i915

00:04.0 Signal processing controller: Intel Corporation Skylake Processor Thermal Subsystem (rev 07)

  Subsystem: Lenovo Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

  Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0

  Interrupt: pin A routed to IRQ 16

  Region 0: Memory at a4710000 (64-bit, non-prefetchable) [size=32K]

  Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-

    Address: 00000000  Data: 0000

  Capabilities: [d0] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [e0] Vendor Specific Information: Len=0c <?>

  Kernel driver in use: proc_thermal

  Kernel modules: processor_thermal_device

00:08.0 System peripheral: Intel Corporation Skylake Gaussian Mixture Model

  Subsystem: Lenovo Xeon E3-1200 v5/v6 / E3-1500 v5 / 6th/7th Gen Core Processor Gaussian Mixture Model

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 255

  Region 0: Memory at a4720000 (64-bit, non-prefetchable) [size=4K]

  Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-

    Address: 00000000  Data: 0000

  Capabilities: [dc] Power Management version 2

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

    Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [f0] PCI Advanced Features

    AFCap: TP+ FLR+

    AFCtrl: FLR-

    AFStatus: TP-

00:12.0 Signal processing controller: Intel Corporation Cannon Lake PCH Thermal Controller (rev 10)

  Subsystem: Lenovo Cannon Lake PCH Thermal Controller

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0

  Interrupt: pin A routed to IRQ 16

  Region 0: Memory at a4721000 (64-bit, non-prefetchable) [size=4K]

  Capabilities: [50] Power Management version 3

    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-

    Address: 00000000  Data: 0000

  Kernel driver in use: intel_pch_thermal

  Kernel modules: intel_pch_thermal

00:14.0 USB controller: Intel Corporation Cannon Lake PCH USB 3.1 xHCI Host Controller (rev 10) (prog-if 30 [XHCI])

  Subsystem: Lenovo Cannon Lake PCH USB 3.1 xHCI Host Controller

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0

  Interrupt: pin ? routed to IRQ 129

  Region 0: Memory at a4700000 (64-bit, non-prefetchable) [size=64K]

  Capabilities: [70] Power Management version 2

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+

    Address: 00000000fee00358  Data: 0000

  Capabilities: [90] Vendor Specific Information: Len=14 <?>

  Kernel driver in use: xhci_hcd

  Kernel modules: xhci_pci

00:14.2 RAM memory: Intel Corporation Cannon Lake PCH Shared SRAM (rev 10)

  Subsystem: Lenovo Cannon Lake PCH Shared SRAM

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Region 0: Memory at a471c000 (64-bit, non-prefetchable) [size=8K]

  Region 2: Memory at a4722000 (64-bit, non-prefetchable) [size=4K]

  Capabilities: [80] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

00:15.0 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH Serial IO I2C Controller (rev 10)

  Subsystem: Lenovo Cannon Lake PCH Serial IO I2C Controller

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 16

  Region 0: Memory at 8f800000 (64-bit, non-prefetchable) [size=4K]

  Capabilities: [80] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

    Status: D3 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [90] Vendor Specific Information: Len=14 <?>

  Kernel driver in use: intel-lpss

  Kernel modules: intel_lpss_pci

00:15.1 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH Serial IO I2C Controller (rev 10)

  Subsystem: Lenovo Cannon Lake PCH Serial IO I2C Controller

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin B routed to IRQ 17

  Region 0: Memory at 8f801000 (64-bit, non-prefetchable) [size=4K]

  Capabilities: [80] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [90] Vendor Specific Information: Len=14 <?>

  Kernel driver in use: intel-lpss

  Kernel modules: intel_lpss_pci

00:16.0 Communication controller: Intel Corporation Cannon Lake PCH HECI Controller (rev 10)

  Subsystem: Lenovo Cannon Lake PCH HECI Controller

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0

  Interrupt: pin A routed to IRQ 140

  Region 0: Memory at a4725000 (64-bit, non-prefetchable) [size=4K]

  Capabilities: [50] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+

    Address: 00000000fee00498  Data: 0000

  Capabilities: [a4] Vendor Specific Information: Len=14 <?>

  Kernel driver in use: mei_me

  Kernel modules: mei_me

00:17.0 SATA controller: Intel Corporation Cannon Lake Mobile PCH SATA AHCI Controller (rev 10) (prog-if 01 [AHCI 1.0])

  Subsystem: Lenovo Cannon Lake Mobile PCH SATA AHCI Controller

  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0

  Interrupt: pin A routed to IRQ 127

  Region 0: Memory at a471e000 (32-bit, non-prefetchable) [size=8K]

  Region 1: Memory at a472a000 (32-bit, non-prefetchable) [size=256]

  Region 2: I/O ports at 5080 [size=8]

  Region 3: I/O ports at 5088 [size=4]

  Region 4: I/O ports at 5060 [size=32]

  Region 5: Memory at a4729000 (32-bit, non-prefetchable) [size=2K]

  Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-

    Address: fee002f8  Data: 0000

  Capabilities: [70] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004

  Kernel driver in use: ahci

  Kernel modules: ahci

00:1d.0 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port (rev f0) (prog-if 00 [Normal decode])

  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 123

  Bus: primary=00, secondary=06, subordinate=06, sec-latency=0

  I/O behind bridge: 0000f000-00000fff

  Memory behind bridge: a4600000-a46fffff

  Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff

  Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

  BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-

    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

  Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00

    DevCap: MaxPayload 256 bytes, PhantFunc 0

      ExtTag- RBE+

    DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+

      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

      MaxPayload 128 bytes, MaxReadReq 128 bytes

    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

    LnkCap: Port #9, Speed 8GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us

      ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+

    LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+

      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

    LnkSta: Speed 8GT/s, Width x2, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-

    SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-

      Slot #8, PowerLimit 25.000W; Interlock- NoCompl+

    SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-

      Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

    SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

      Changed: MRL- PresDet- LinkState+

    RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-

    RootCap: CRSVisible-

    RootSta: PME ReqID 0000, PMEStatus- PMEPending-

    DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+, OBFF Not Supported ARIFwd+

    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-

    LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-

       Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

       Compliance De-emphasis: -6dB

    LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete+, EqualizationPhase1+

       EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-

  Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-

    Address: fee00258  Data: 0000

  Capabilities: [90] Subsystem: Illegal Vendor ID Cannon Lake PCH PCI Express Root Port

  Capabilities: [a0] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

    Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [100 v1] Advanced Error Reporting

    UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

    CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

    CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

    AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-

  Capabilities: [140 v1] Access Control Services

    ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-

    ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-

  Capabilities: [150 v1] Precision Time Measurement

    PTMCap: Requester:- Responder:+ Root:+

    PTMClockGranularity: 4ns

    PTMControl: Enabled:+ RootSelected:+

    PTMEffectiveGranularity: Unknown

  Capabilities: [200 v1] L1 PM Substates

    L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+

        PortCommonModeRestoreTime=40us PortTPowerOnTime=44us

    L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+

         T_CommonMode=40us LTR1.2_Threshold=81920ns

    L1SubCtl2: T_PwrOn=44us

  Capabilities: [220 v1] #19

  Capabilities: [250 v1] Downstream Port Containment

    DpcCap: INT Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+

    DpcCtl: Trigger:1 Cmpl- INT+ ErrCor- PoisonedTLP- SwTrigger- DL_ActiveErr-

    DpcSta: Trigger- Reason:00 INT- RPBusy- TriggerExt:00 RP PIO ErrPtr:1f

    Source: 0000

  Kernel driver in use: pcieport

00:1d.4 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port (rev f0) (prog-if 00 [Normal decode])

  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 124

  Bus: primary=00, secondary=07, subordinate=07, sec-latency=0

  I/O behind bridge: 0000f000-00000fff

  Memory behind bridge: a4200000-a43fffff

  Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff

  Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

  BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-

    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

  Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00

    DevCap: MaxPayload 256 bytes, PhantFunc 0

      ExtTag- RBE+

    DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

      MaxPayload 256 bytes, MaxReadReq 128 bytes

    DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

    LnkCap: Port #13, Speed 8GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us

      ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+

    LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- CommClk+

      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

    LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-

    SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-

      Slot #12, PowerLimit 10.000W; Interlock- NoCompl+

    SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-

      Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

    SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

      Changed: MRL- PresDet- LinkState+

    RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-

    RootCap: CRSVisible-

    RootSta: PME ReqID 0000, PMEStatus- PMEPending-

    DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+, OBFF Not Supported ARIFwd+

    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-

    LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-

       Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

       Compliance De-emphasis: -6dB

    LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-

       EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-

  Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-

    Address: fee00278  Data: 0000

  Capabilities: [90] Subsystem: Lenovo Cannon Lake PCH PCI Express Root Port

  Capabilities: [a0] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

    Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [100 v0] #00

  Capabilities: [140 v1] Access Control Services

    ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-

    ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-

  Capabilities: [150 v1] Precision Time Measurement

    PTMCap: Requester:- Responder:+ Root:+

    PTMClockGranularity: 4ns

    PTMControl: Enabled:+ RootSelected:+

    PTMEffectiveGranularity: Unknown

  Capabilities: [200 v1] L1 PM Substates

    L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+

        PortCommonModeRestoreTime=40us PortTPowerOnTime=44us

    L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+

         T_CommonMode=50us LTR1.2_Threshold=81920ns

    L1SubCtl2: T_PwrOn=44us

  Capabilities: [220 v1] #19

  Capabilities: [250 v1] Downstream Port Containment

    DpcCap: INT Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+

    DpcCtl: Trigger:0 Cmpl- INT- ErrCor- PoisonedTLP- SwTrigger- DL_ActiveErr-

    DpcSta: Trigger- Reason:00 INT- RPBusy- TriggerExt:00 RP PIO ErrPtr:1f

    Source: 0000

  Kernel driver in use: pcieport

00:1d.5 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port (rev f0) (prog-if 00 [Normal decode])

  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin B routed to IRQ 125

  Bus: primary=00, secondary=08, subordinate=08, sec-latency=0

  I/O behind bridge: 00003000-00003fff

  Memory behind bridge: a4500000-a45fffff

  Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff

  Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-

  BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-

    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

  Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00

    DevCap: MaxPayload 256 bytes, PhantFunc 0

      ExtTag- RBE+

    DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+

      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-

      MaxPayload 128 bytes, MaxReadReq 128 bytes

    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

    LnkCap: Port #14, Speed 8GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us

      ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+

    LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+

      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

    LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-

    SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-

      Slot #13, PowerLimit 10.000W; Interlock- NoCompl+

    SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-

      Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

    SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

      Changed: MRL- PresDet- LinkState+

    RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-

    RootCap: CRSVisible-

    RootSta: PME ReqID 0000, PMEStatus- PMEPending-

    DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+, OBFF Not Supported ARIFwd+

    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled ARIFwd-

    LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-

       Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

       Compliance De-emphasis: -6dB

    LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-

       EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-

  Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-

    Address: fee002b8  Data: 0000

  Capabilities: [90] Subsystem: Lenovo Cannon Lake PCH PCI Express Root Port

  Capabilities: [a0] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

    Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [100 v1] Advanced Error Reporting

    UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

    CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

    CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

    AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-

  Capabilities: [140 v1] Access Control Services

    ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-

    ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-

  Capabilities: [150 v1] Precision Time Measurement

    PTMCap: Requester:- Responder:+ Root:+

    PTMClockGranularity: 4ns

    PTMControl: Enabled:+ RootSelected:+

    PTMEffectiveGranularity: Unknown

  Capabilities: [200 v1] L1 PM Substates

    L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+

        PortCommonModeRestoreTime=40us PortTPowerOnTime=44us

    L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+

         T_CommonMode=150us LTR1.2_Threshold=81920ns

    L1SubCtl2: T_PwrOn=150us

  Capabilities: [220 v1] #19

  Capabilities: [250 v1] Downstream Port Containment

    DpcCap: INT Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+

    DpcCtl: Trigger:1 Cmpl- INT+ ErrCor- PoisonedTLP- SwTrigger- DL_ActiveErr-

    DpcSta: Trigger- Reason:00 INT- RPBusy- TriggerExt:00 RP PIO ErrPtr:1f

    Source: 0000

  Kernel driver in use: pcieport

00:1e.0 Communication controller: Intel Corporation Device a328 (rev 10)

  Subsystem: Lenovo Device 380f

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 20

  Region 0: Memory at 8f802000 (64-bit, non-prefetchable) [size=4K]

  Capabilities: [80] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

    Status: D3 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [90] Vendor Specific Information: Len=14 <?>

  Kernel driver in use: intel-lpss

  Kernel modules: intel_lpss_pci

00:1f.0 ISA bridge: Intel Corporation Device a30d (rev 10)

  Subsystem: Lenovo Device 3810

  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

  Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0

00:1f.3 Audio device: Intel Corporation Cannon Lake PCH cAVS (rev 10)

  Subsystem: Lenovo Cannon Lake PCH cAVS

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 32, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 141

  Region 0: Memory at a4718000 (64-bit, non-prefetchable) [size=16K]

  Region 4: Memory at a4400000 (64-bit, non-prefetchable) [size=1M]

  Capabilities: [50] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [80] Vendor Specific Information: Len=14 <?>

  Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+

    Address: 00000000fee004b8  Data: 0000

  Kernel driver in use: snd_hda_intel

  Kernel modules: snd_hda_intel

00:1f.4 SMBus: Intel Corporation Cannon Lake PCH SMBus Controller (rev 10)

  Subsystem: Lenovo Cannon Lake PCH SMBus Controller

  Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

  Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Interrupt: pin A routed to IRQ 16

  Region 0: Memory at a4727000 (64-bit, non-prefetchable) [size=256]

  Region 4: I/O ports at 5040 [size=32]

  Kernel driver in use: i801_smbus

  Kernel modules: i2c_i801

00:1f.5 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH SPI Controller (rev 10)

  Subsystem: Lenovo Cannon Lake PCH SPI Controller

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0

  Region 0: Memory at fe010000 (32-bit, non-prefetchable) [size=4K]

01:00.0 VGA compatible controller: NVIDIA Corporation GP107M [GeForce GTX 1050 Mobile] (rev a1) (prog-if 00 [VGA controller])

  Subsystem: Lenovo GP107M [GeForce GTX 1050 Mobile]

  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 131

  Region 0: Memory at a3000000 (32-bit, non-prefetchable) [size=16M]

  Region 1: Memory at 90000000 (64-bit, prefetchable) [size=256M]

  Region 3: Memory at a0000000 (64-bit, prefetchable) [size=32M]

  Region 5: I/O ports at 4000 [size=128]

  Expansion ROM at a4000000 [disabled] [size=512K]

  Capabilities: [60] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+

    Address: 00000000fee00378  Data: 0000

  Capabilities: [78] Express (v2) Endpoint, MSI 00

    DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us

      ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 75.000W

    DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

      RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+

      MaxPayload 256 bytes, MaxReadReq 512 bytes

    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-

    LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <512ns, L1 <4us

      ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+

    LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+

      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

    LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

    DevCap2: Completion Timeout: Range AB, TimeoutDis+, LTR+, OBFF Via message

    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled

    LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-

       Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

       Compliance De-emphasis: -6dB

    LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete+, EqualizationPhase1+

       EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-

  Capabilities: [100 v1] Virtual Channel

    Caps: LPEVC=0 RefClk=100ns PATEntryBits=1

    Arb:  Fixed- WRR32- WRR64- WRR128-

    Ctrl: ArbSelect=Fixed

    Status: InProgress-

    VC0:  Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-

      Arb:  Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-

      Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff

      Status: NegoPending- InProgress-

  Capabilities: [250 v1] Latency Tolerance Reporting

    Max snoop latency: 0ns

    Max no snoop latency: 0ns

  Capabilities: [258 v1] L1 PM Substates

    L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+

        PortCommonModeRestoreTime=255us PortTPowerOnTime=10us

    L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-

         T_CommonMode=0us LTR1.2_Threshold=0ns

    L1SubCtl2: T_PwrOn=10us

  Capabilities: [128 v1] Power Budgeting <?>

  Capabilities: [420 v2] Advanced Error Reporting

    UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

    CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

    CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

    AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-

  Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>

  Capabilities: [900 v1] #19

  Kernel driver in use: nouveau

  Kernel modules: nouveau

06:00.0 Non-Volatile memory controller: SK hynix Device 1327 (prog-if 02 [NVM Express])

  Subsystem: SK hynix Device 0000

  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 16

  NUMA node: 0

  Region 0: Memory at a4600000 (64-bit, non-prefetchable) [size=16K]

  Capabilities: [80] Power Management version 3

    Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [90] MSI: Enable- Count=1/32 Maskable+ 64bit+

    Address: 0000000000000000  Data: 0000

    Masking: 00000000  Pending: 00000000

  Capabilities: [b0] MSI-X: Enable+ Count=32 Masked-

    Vector table: BAR=0 offset=00002000

    PBA: BAR=0 offset=00003000

  Capabilities: [c0] Express (v2) Endpoint, MSI 00

    DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited

      ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 75.000W

    DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+

      RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-

      MaxPayload 128 bytes, MaxReadReq 512 bytes

    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-

    LnkCap: Port #0, Speed 8GT/s, Width x2, ASPM L1, Exit Latency L0s <4us, L1 <64us

      ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+

    LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+

      ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-

    LnkSta: Speed 8GT/s, Width x2, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

    DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Not Supported

    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled

    LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-

       Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

       Compliance De-emphasis: -6dB

    LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete+, EqualizationPhase1+

       EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-

  Capabilities: [100 v2] Advanced Error Reporting

    UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

    CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

    CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

    AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-

  Capabilities: [150 v1] Device Serial Number 00-00-00-00-00-00-00-00

  Capabilities: [160 v1] Power Budgeting <?>

  Capabilities: [1b8 v1] Latency Tolerance Reporting

    Max snoop latency: 3145728ns

    Max no snoop latency: 3145728ns

  Capabilities: [300 v1] #19

  Capabilities: [400 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>

  Capabilities: [900 v1] L1 PM Substates

    L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+

        PortCommonModeRestoreTime=24us PortTPowerOnTime=26us

    L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+

         T_CommonMode=0us LTR1.2_Threshold=81920ns

    L1SubCtl2: T_PwrOn=44us

  Kernel driver in use: nvme

  Kernel modules: nvme

07:00.0 Network controller: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter (rev 31)

  Subsystem: Lenovo QCA9377 802.11ac Wireless Network Adapter

  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 142

  Region 0: Memory at a4200000 (64-bit, non-prefetchable) [size=2M]

  Capabilities: [40] Power Management version 3

    Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)

    Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit-

    Address: fee004d8  Data: 0000

    Masking: 000000fe  Pending: 00000000

  Capabilities: [70] Express (v2) Endpoint, MSI 00

    DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us

      ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W

    DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

      RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-

      MaxPayload 256 bytes, MaxReadReq 512 bytes

    DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

    LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us

      ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+

    LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- CommClk+

      ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-

    LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

    DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR+, OBFF Via message

    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled

    LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-

       Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

       Compliance De-emphasis: -6dB

    LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-

       EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-

  Capabilities: [100 v2] Advanced Error Reporting

    UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

    CESta:  RxErr+ BadTLP+ BadDLLP- Rollover- Timeout+ NonFatalErr-

    CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

    AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-

  Capabilities: [148 v1] Virtual Channel

    Caps: LPEVC=0 RefClk=100ns PATEntryBits=1

    Arb:  Fixed- WRR32- WRR64- WRR128-

    Ctrl: ArbSelect=Fixed

    Status: InProgress-

    VC0:  Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-

      Arb:  Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-

      Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff

      Status: NegoPending- InProgress-

  Capabilities: [168 v1] Device Serial Number 00-00-00-00-00-00-00-00

  Capabilities: [178 v1] Latency Tolerance Reporting

    Max snoop latency: 3145728ns

    Max no snoop latency: 3145728ns

  Capabilities: [180 v1] L1 PM Substates

    L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+

        PortCommonModeRestoreTime=50us PortTPowerOnTime=10us

    L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+

         T_CommonMode=0us LTR1.2_Threshold=81920ns

    L1SubCtl2: T_PwrOn=44us

  Kernel driver in use: ath10k_pci

  Kernel modules: ath10k_pci

08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 15)

  Subsystem: Lenovo RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller

  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+

  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

  Latency: 0, Cache Line Size: 64 bytes

  Interrupt: pin A routed to IRQ 17

  Region 0: I/O ports at 3000 [size=256]

  Region 2: Memory at a4504000 (64-bit, non-prefetchable) [size=4K]

  Region 4: Memory at a4500000 (64-bit, non-prefetchable) [size=16K]

  Capabilities: [40] Power Management version 3

    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)

    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

  Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+

    Address: 0000000000000000  Data: 0000

  Capabilities: [70] Express (v2) Endpoint, MSI 01

    DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us

      ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W

    DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

      RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-

      MaxPayload 128 bytes, MaxReadReq 4096 bytes

    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-

    LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us

      ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+

    LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+

      ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-

    LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-

    DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Via message/WAKE#

    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled

    LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-

       Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-

       Compliance De-emphasis: -6dB

    LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-

       EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-

  Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-

    Vector table: BAR=4 offset=00000000

    PBA: BAR=4 offset=00000800

  Capabilities: [100 v2] Advanced Error Reporting

    UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-

    UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-

    CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-

    CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+

    AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-

  Capabilities: [140 v1] Virtual Channel

    Caps: LPEVC=0 RefClk=100ns PATEntryBits=1

    Arb:  Fixed- WRR32- WRR64- WRR128-

    Ctrl: ArbSelect=Fixed

    Status: InProgress-

    VC0:  Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-

      Arb:  Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-

      Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff

      Status: NegoPending- InProgress-

  Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00

  Capabilities: [170 v1] Latency Tolerance Reporting

    Max snoop latency: 3145728ns

    Max no snoop latency: 3145728ns

  Capabilities: [178 v1] L1 PM Substates

    L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+

        PortCommonModeRestoreTime=150us PortTPowerOnTime=150us

    L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+

         T_CommonMode=0us LTR1.2_Threshold=81920ns

    L1SubCtl2: T_PwrOn=150us

  Kernel driver in use: r8169

  Kernel modules: r8169

 dmesg | grep -i kernel

 [    0.000000] Linux version 4.19.0-8-amd64 (debian-kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP Debian 4.19.98-1 (2020-01-26)

[    0.063366] Booting paravirtualized kernel on bare hardware

[    0.168715] random: get_random_bytes called from start_kernel+0x93/0x52c with crng_init=0

[    0.168945] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.19.0-8-amd64 root=UUID=2696963a-f2a1-4437-aeb7-f5881b5c548a ro quiet

[    0.195214] Memory: 7939700K/8259892K available (10252K kernel code, 1241K rwdata, 3320K rodata, 1592K init, 2276K bss, 320192K reserved, 0K cma-reserved)

[    0.195309] Kernel/User page tables isolation: enabled

[    0.257796] Yama: disabled by default; enable with sysctl kernel.yama.*

[    0.272196] MDS CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/mds.html for more details.

[    1.502629] Freeing unused kernel image memory: 1592K

[    1.540318] Write protecting the kernel read-only data: 16384k

[    1.542807] Freeing unused kernel image memory: 2028K

[    1.542981] Freeing unused kernel image memory: 776K

[    1.695457] i915 0000:00:02.0: DMC firmware homepage: https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/i915

[    1.825592] [TTM] Zone  kernel: Available graphics memory: 4020354 kiB

[    1.872498] nouveau 0000:01:00.0: DRM: failed to create kernel channel, -22

uname -a

  Linux debian 4.19.0-8-amd64 #1 SMP Debian 4.19.98-1 (2020-01-26) x86_64 GNU/Linux

 

Arghalion · 09-02-2020 12:44:20

il s'agit du Lenovo Legion Y530-15ICH

je reboot immediatement

Beta-Pictoris · 09-02-2020 12:45:41

Belle machine.

Arghalion · 09-02-2020 12:55:59

Beta-Pictoris a écrit :

Belle machine.

de quoi faire tourner des petits jeux et bien coder

Oh oui la clé wifi marche

merci merci merci !

je ferais sans la wifi du pc

je suis étonné du nombre de choses a connaître, ou peut on trouver des sources pour débutant (donc pas la doc pure)?

Debian-facile

#1 09-02-2020 00:08:50

Ne peux pas activer la wifi

#2 09-02-2020 00:13:25

Re : Ne peux pas activer la wifi

#3 09-02-2020 00:20:43

Re : Ne peux pas activer la wifi

#4 09-02-2020 00:32:11

Re : Ne peux pas activer la wifi

#5 09-02-2020 00:43:43

Re : Ne peux pas activer la wifi

#6 09-02-2020 00:49:37

Re : Ne peux pas activer la wifi

#7 09-02-2020 00:52:17

Re : Ne peux pas activer la wifi

#8 09-02-2020 00:55:37

Re : Ne peux pas activer la wifi

#9 09-02-2020 01:05:12

Re : Ne peux pas activer la wifi

#10 09-02-2020 01:11:05

Re : Ne peux pas activer la wifi

#11 09-02-2020 01:12:48

Re : Ne peux pas activer la wifi

#12 09-02-2020 01:15:30

Re : Ne peux pas activer la wifi

#13 09-02-2020 01:16:05

Re : Ne peux pas activer la wifi

#14 09-02-2020 01:49:59

Re : Ne peux pas activer la wifi

#15 09-02-2020 02:11:38

Re : Ne peux pas activer la wifi

#16 09-02-2020 08:25:33

Re : Ne peux pas activer la wifi

#17 09-02-2020 10:07:50

Re : Ne peux pas activer la wifi

#18 09-02-2020 10:17:58

Re : Ne peux pas activer la wifi

#19 09-02-2020 10:30:51

Re : Ne peux pas activer la wifi

#20 09-02-2020 12:11:19

Re : Ne peux pas activer la wifi

#21 09-02-2020 12:36:50

Re : Ne peux pas activer la wifi

#22 09-02-2020 12:39:35

Re : Ne peux pas activer la wifi

#23 09-02-2020 12:44:20

Re : Ne peux pas activer la wifi

#24 09-02-2020 12:45:41

Re : Ne peux pas activer la wifi

#25 09-02-2020 12:55:59

Re : Ne peux pas activer la wifi

Pied de page des forums