Bonjour,
j'ai un petit soucis.. la sortie HDMI de mon laptop n'est pas fonctionnel..
petit récap :
J'ai le driver proprio installer (fglrx), mon pc (Lenovo Thinkpad Edge E520) possède 2 carte graphique switchable.
lspci -vnn | egrep "VGA|3D|Display"
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) (prog-if 00 [VGA controller])
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Whistler [AMD Radeon HD 6600M Series] [1002:6741] (prog-if 00 [VGA controller])
glxinfo | grep OpenGL
OpenGL vendor string: Advanced Micro Devices, Inc.
OpenGL renderer string: AMD Radeon 6600M and 6700M Series
OpenGL version string: 4.2.11762 Compatibility Profile Context
OpenGL shading language version string: 4.20
OpenGL extensions:
fglrxinfo
display: :0 screen: 0
OpenGL vendor string: Advanced Micro Devices, Inc.
OpenGL renderer string: AMD Radeon 6600M and 6700M Series
OpenGL version string: 4.2.11762 Compatibility Profile Context
grep HDMI /var/log/Xorg.0.log
[ 27.559] (II) fglrx(0): Output HDMI1 has no monitor section
[ 27.611] (II) fglrx(0): EDID for output HDMI1
[ 27.660] (II) fglrx(0): Output HDMI1 disconnected
[ 32.248] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event10)
sudo get-edid | parse-edid
parse-edid: parse-edid version 2.0.0
get-edid: get-edid version 2.0.0
Performing real mode VBE call
Interrupt 0x10 ax=0x4f00 bx=0x0 cx=0x0
Function supported
Call successful
VBE version 300
VBE string at 0x11100 "Intel(R)Sandybridge Mobile Graphics Chipset Accelerated VGA BIOS"
VBE/DDC service about to be called
Report DDC capabilities
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x0 cx=0x0
Function supported
Call successful
Monitor and video card combination does not support DDC1 transfers
Monitor and video card combination supports DDC2 transfers
0 seconds per 128 byte EDID block transfer
Screen is not blanked during DDC transfer
Reading next EDID block
VBE/DDC service about to be called
Read EDID
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x1 cx=0x0
Function supported
Call successful
parse-edid: EDID checksum passed.
# EDID version 1 revision 3
Section "Monitor"
# Block type: 2:0 3:f
# Block type: 2:0 3:fe
# Block type: 2:0 3:fe
Identifier "SEC:5230"
VendorName "SEC"
ModelName "SEC:5230"
# Block type: 2:0 3:f
# Block type: 2:0 3:fe
# Block type: 2:0 3:fe
# DPMS capabilities: Active off:yes Suspend:yes Standby:yes
Mode "1366x768" # vfreq 59.998Hz, hfreq 47.398kHz
DotClock 72.330000
HTimings 1366 1414 1446 1526
VTimings 768 770 775 790
Flags "-HSync" "-VSync"
EndMode
# Block type: 2:0 3:f
# Block type: 2:0 3:fe
# Block type: 2:0 3:fe
EndSection
dmesg
[ 10.349627] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[ 10.349952] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
Aucun evenement lorsque je branche/débranche le cable hdmi (TV allumé) sur la sortie hdmi du pc :
sudo udevadm monitor
monitor will print the received events for:
UDEV - the event which udev sends out after rule processing
KERNEL - the kernel uevent
xrandr
Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192
LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 194mm
1366x768 60.0*+
1360x768 59.8 60.0
1024x768 60.0
800x600 60.3 56.2
640x480 59.9
VGA1 disconnected (normal left inverted right x axis y axis)
HDMI1 disconnected (normal left inverted right x axis y axis)
DP1 disconnected (normal left inverted right x axis y axis)
La sortie VGA1 fonctionne correctement.
petit truc bizarre, lorsque que ma TV et branché sur la sortie HDMI du pc et qu'elle s’étend parce qu'il n'y a aucun signal, la souris de mon pc est trrrrrèèèès lente..
il me suffit de débranché le cable hdmi pour qu'elle revienne à la normal...
Merci pour tout aide apporté
EDIT#1:
cat /etc/X11/xorg.conf
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
Monitor "aticonfig-Monitor[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Dernière modification par z0rg> (23-11-2014 13:47:10)