[RÉSOLU] Ecran freeze suite à installation bumblebee

Manahoar · 05-04-2017 00:18:55

Coucou

J'ai récemment installé Debian Stretch sur mon PC portable Asus ROG avec une CG Nvidia 960m, j'ai vu sur internet que Linux avait quelques problèmes lorsqu'il devait gérer 2 CG mais qu'il existait une solution avec Bumblebee. J'ai donc suivi ce tuto:

https://debian-facile.org/doc:materiel: … ia:optimus

J'ai essayé l'installation avec le module nouveau et le module prioritaire Nvidia et dans les deux cas lorsque j'arrive sur la page de log-in, j'entre mes identifiants et tout de suite après avoir cliqué sur le bouton connecter j'ai subitement un écran noir qui s'éteint et PLUS rien ne fonctionne.

Je souligne que si je fais Ctrl+Alt+F2 j'arrive à me connecter en terminal SANS interface graphique et tout marche parfaitement. C'est seulement lorsque je me connecte en interface graphique que j'ai cet écran noir. J'ai cherché partout et je n'arrive pas à trouver la solution

Je ne sais pas si ça peut aider, mais lorsque j'utilise "nvidia-detect" le terminal se met à crash et impossible de reprendre le control.

Info complémentaire: Avant d'installer bumblebee et les pilotes Nvidia, je devais taper dans le grub au lancement ces commandes:

nouveau.modeset=0

Si je ne faisais pas ça, une fois que j'entrais mes logs mon clavier et mon pavé tactile ne répondais plus. J'ai lu sur internet que ceci permettait au lancement de désactiver la CG Nvidia et tout fonctionnait parfaitement.

Franchement si vous pouviez m'aider ce serait vraiment cool !

Dernière modification par Manahoar (05-04-2017 20:17:52)

anonyme · 05-04-2017 00:26:04

Bonsoir
il se peu que ton portable n'ai qu'une carte nvidia , il faudrai la référence exacte , Asus Rog ça ne suffit pas.

quand tu est en console pure , tape la commande lspci

lspci

 

et poste le retour sur le forum (si tu a une autre machine pour te connecter au forum )
nota : par la combinaison des touches Ctrl+Alt+F1 a l invite de loging , ou si ça plante (comme tu a fait sur ton post ci dessus )

ce qui nous intéresse : (un exemple )

00.0 VGA compatible controller: NVIDIA Corporation GM107 [GeForce GTX 750 Ti] (rev a2)

00.1 Audio device: NVIDIA Corporation Device 0fbc (rev a1)

00.0 VGA compatible controller: NVIDIA Corporation GM107 [GeForce GTX 750 Ti] (rev a2)

00.1 Audio device: NVIDIA Corporation Device 0fbc (rev a1)

c'est les lignes qui commence par "VGA"

pour ceci "nouveau.modeset=0" tu a blacklisté nouveau de KMS (modesetting du noyau ) a quel endroit a tu entrer cette ligne , dans GRUB ? ou ailleurs ?

tu a aussi nouveau qui peut etre blacklisté par un fichier dans /etc/mod-probe.d/20-blacklist-nouveau.conf avec ceci dedans

# You need to run "update-initramfs -u" after editing this file.

# see #580894

blacklist nouveau

je te conseille pour travailler convenablement d utiliser le bureau Mate au lieu de gnome

apt-get update

 

apt-get install mate-core lightdm synaptic gedit

 

a la question quel lanceur sélectionner répond "lightdm" (ne plus utiliser gdm3)

desinstaller bumblebee et le purger (tu dois purger aussi le driver nvidia si besoin )

gnome pose problème pour les ressources graphiques si le serveur X fonctionne mal , mate demande moins de ressources , lorsque ton portable sera bien configuré tu pourra remettre gnome.
normalement tu devrais pouvoir ouvrir ton bureau Mate

tu dois te trouver en "vesa" et une définition pourri
tu peu enlever "nouveau.modeset=0" (pour remettre KMS en service) et supprimer le fichier "20-blacklist-nouveau.conf" pour enlever le blacklistage de nouveau , un reboot
tu dois toujours pouvoir te connecter a ton bureau Mate.
si jusque la tout va bien on verra pour la suite

Dernière modification par anonyme (05-04-2017 00:55:24)

Manahoar · 05-04-2017 00:49:24

Salut anonyme, merci pour ta réponse rapide.

Donc pour te répondre,

pour ceci "nouveau.modeset=0" tu a blacklisté nouveau de KMS (modesetting du noyau ) a quel endroit a tu entrer cette ligne , dans GRUB ? ou ailleurs ?

Arrivé sur grub, j'appui sur e pour éditer puis je l'ai ajouté à la ligne qui débute par linux et qui se termine par quiet au début ça marchait quand j'entrais cette ligne mais depuis que j'ai installé Bumblebee cette astuce ne fonctionne plus avec ou sans.

Quant aux logs de lspci je n'ai qu'une seule ligne VGA mais une autre qui mentionne ma GTX 960m.

log lspci

02.0 VGA compatible controller: Intel Corporation HD Graphics 530 (rev 06)

00.0 3D controller: NVIDIA Corporation GM107 [GeForce GTX 960M] (rev ff)

tu a aussi nouveau qui peut etre blacklisté par un fichier dans /etc/mod-probe.d/20-blacklist-nouveau.conf avec ceci dedans

J'ai bien un fichier de ce type dans cat /etc/modprobe.d/nvidia-blacklists-nouveau.conf

A l'intérieur de ce fichier:

blacklist nouveau

anonyme · 05-04-2017 01:00:23

ok donc tu a le driver nvidia installé a cause de ceci "cat /etc/modprobe.d/nvidia-blacklists-nouveau.conf"
il faudrait le désinstaller (ainsi que bumblebee )
tu a 2 cartes , une intel et une nvidia
je pense que gnome plante parce que ta carte intel est mal reconnu
donc il faut commencer par la (et ignorer la nvidia pour l instant )
nota : relit mon premier post au dessus je l ai complété

si tu est a l'aise en console pure (pas graphique) tu peu rester sous gnome (mais sans te logger)
purger bumblebee et le driver nvidia

avec le driver de KMS (pour intel) je pense que tu peu faire ceci :

pour bumblebee un "remove --purge" de ce que tu a installé
pour nvidia

apt-get remove --purge nvidia*

 

apt-get remove --purge xserver-xorg-video-intel xserver-xorg-video-nouveau

 

il faut un reboot ensuite

si tu a bien désinstallé nvidia , ceci ne doit plus exister : => cat /etc/modprobe.d/nvidia-blacklists-nouveau.conf

Dernière modification par anonyme (05-04-2017 01:11:37)

Manahoar · 05-04-2017 01:11:21

Ok donc voici ce que j'ai fais:

apt-get remove --purge nvidia*

apt-get remove --purge bumblebee

J'ai ensuite installé Mate comme demandé:

 apt-get install mate-core lightdm synaptic gedit

Supprimé le fichier qui blacklist le module nouveau:

rm /etc/modprobe.d/nvidia-blacklists-nouveau.conf

Je reboot, j'arrive au moment de log-in dans l'interface Mate. J'entre mon username et mon password mais dès que je me connecte je n'ai que le fond d'écran qui s'affiche et la souris que je peu déplacer. Rien d'autre.

EDIT: Ok si je peux rester en console pure je le ferais ça ne me dérange absolument pas.

Dernière modification par Manahoar (05-04-2017 01:12:33)

anonyme · 05-04-2017 01:13:43

tu utilise bien "lightdm" pour te logger sur le bureau et tu choisi mate comme bureau (voir en haut a droite , choix du bureau a l invite de logging )
nota : pour le lanceur gdm3 c'est le petit engrenage pour le choix du bureau (en dessous l endroit ou tu entre le mot de passe )

Dernière modification par anonyme (05-04-2017 01:16:05)

Manahoar · 05-04-2017 01:16:33

Ah punaise quel boulet excuse moi j'étais bien sosu lightdm mais je n'avais pas choisis Mate. C'est bon là ça marche parfaitement avec l'interface Mate !

anonyme · 05-04-2017 01:20:47

ok bon je te préviens suis plutot "PC bureau" donc je connais bien intel , je connais bien nvidia mais pour bumblebee je laisserai faire les jeun's

pour intel jeter un oeil sur le Xorg.0.log : qui se trouve
pour Mate dans

cat /var/log/Xorg.0.log

 

nota : pour gnome tu le trouve dans ton /home/user/.local/share/X11/Xorg.0.log (bon de tete , peut etre une erreur ), on le trouve aussi dans /usr/gdm3 (un truc comme ça ) pour la suite si tu repasse a gnome
le log doit etre daté du dernier démarrage de la machine (leur truc de mettre les logs un peu partout pas cool pour savoir ci c'est le bon )
donc toi c'est le premier au dessus pour mate (/var/log/Xorg.0.log )

normalement avec un cpu SkyLake (530) KMS doit bien fonctionner , donc si tu a supprimé le driver intel et nouveau (comme indiqué au dessus ) le retour du log doit etre correct pour intel.
avec les balises "code" tu dois pouvoir le poster ( a partir du bureau )

ps: gnome a besoin de DRI2 et GLX configuré correctement

Dernière modification par anonyme (05-04-2017 01:37:52)

Manahoar · 05-04-2017 01:35:03

Ok merci pour ton aide donc voici ce que j'ai dans /var/log/Xorg.0.log

[     4.886] 

X.Org X Server 1.19.2

Release Date: 2017-03-02

[     4.886] X Protocol Version 11, Revision 0

[     4.886] Build Operating System: Linux 3.16.0-4-amd64 x86_64 Debian

[     4.886] Current Operating System: Linux debian-mnhr 4.9.0-2-amd64 #1 SMP Debian 4.9.13-1 (2017-02-27) x86_64

[     4.886] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-2-amd64 root=UUID=d11a650c-29a7-47bc-99af-e1b4de5522ea ro quiet

[     4.886] Build Date: 03 March 2017  03:14:41PM

[     4.886] xorg-server 2:1.19.2-1 (https://www.debian.org/support) 

[     4.886] Current version of pixman: 0.34.0

[     4.886]  Before reporting problems, check http://wiki.x.org

  to make sure that you have the latest version.

[     4.886] Markers: (--) probed, (**) from config file, (==) default setting,

  (++) from command line, (!!) notice, (II) informational,

  (WW) warning, (EE) error, (NI) not implemented, (??) unknown.

[     4.886] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Apr  5 02:15:28 2017

[     4.892] (==) Using system config directory "/usr/share/X11/xorg.conf.d"

[     4.893] (==) No Layout section.  Using the first Screen section.

[     4.893] (==) No screen section available. Using defaults.

[     4.893] (**) |-->Screen "Default Screen Section" (0)

[     4.893] (**) |   |-->Monitor "<default monitor>"

[     4.894] (==) No monitor specified for screen "Default Screen Section".

  Using a default monitor configuration.

[     4.894] (==) Automatically adding devices

[     4.894] (==) Automatically enabling devices

[     4.894] (==) Automatically adding GPU devices

[     4.894] (==) Max clients allowed: 256, resource mask: 0x1fffff

[     4.895] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.

[     4.895]  Entry deleted from font path.

[     4.895] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.

[     4.895]  Entry deleted from font path.

[     4.895] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.

[     4.895]  Entry deleted from font path.

[     4.896] (WW) The directory "/usr/share/fonts/X11/Type1" does not exist.

[     4.896]  Entry deleted from font path.

[     4.896] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.

[     4.896]  Entry deleted from font path.

[     4.896] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.

[     4.896]  Entry deleted from font path.

[     4.896] (==) FontPath set to:

  /usr/share/fonts/X11/misc,

  built-ins

[     4.896] (==) ModulePath set to "/usr/lib/xorg/modules"

[     4.896] (II) The server relies on udev to provide the list of input devices.

  If no devices become available, reconfigure udev or disable AutoAddDevices.

[     4.896] (II) Loader magic: 0x563c7947ce00

[     4.896] (II) Module ABI versions:

[     4.896]  X.Org ANSI C Emulation: 0.4

[     4.896]  X.Org Video Driver: 23.0

[     4.896]  X.Org XInput driver : 24.1

[     4.896]  X.Org Server Extension : 10.0

[     4.896] (++) using VT number 7

[     4.896] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration

[     4.896] (II) xfree86: Adding drm device (/dev/dri/card1)

[     4.897] (II) xfree86: Adding drm device (/dev/dri/card0)

[     4.912] (--) PCI:*(0:0:2:0) 8086:191b:1043:1c5d rev 6, Mem @ 0xdd000000/16777216, 0xb0000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072

[     4.912] (--) PCI: (0:1:0:0) 10de:139b:1043:1c5d rev 162, Mem @ 0xde000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288

[     4.912] (II) LoadModule: "glx"

[     4.914] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so

[     4.924] (II) Module glx: vendor="X.Org Foundation"

[     4.924]  compiled for 1.19.2, module version = 1.0.0

[     4.924]  ABI class: X.Org Server Extension, version 10.0

[     4.924] (==) Matched nouveau as autoconfigured driver 0

[     4.924] (==) Matched nv as autoconfigured driver 1

[     4.924] (==) Matched modesetting as autoconfigured driver 2

[     4.924] (==) Matched fbdev as autoconfigured driver 3

[     4.924] (==) Matched vesa as autoconfigured driver 4

[     4.924] (==) Assigned the driver to the xf86ConfigLayout

[     4.924] (II) LoadModule: "nouveau"

[     4.924] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so

[     4.927] (II) Module nouveau: vendor="X.Org Foundation"

[     4.927]  compiled for 1.19.2, module version = 1.0.13

[     4.927]  Module class: X.Org Video Driver

[     4.927]  ABI class: X.Org Video Driver, version 23.0

[     4.927] (II) LoadModule: "nv"

[     4.927] (WW) Warning, couldn't open module nv

[     4.927] (II) UnloadModule: "nv"

[     4.927] (II) Unloading nv

[     4.927] (EE) Failed to load module "nv" (module does not exist, 0)

[     4.927] (II) LoadModule: "modesetting"

[     4.927] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so

[     4.928] (II) Module modesetting: vendor="X.Org Foundation"

[     4.928]  compiled for 1.19.2, module version = 1.19.2

[     4.928]  Module class: X.Org Video Driver

[     4.928]  ABI class: X.Org Video Driver, version 23.0

[     4.928] (II) LoadModule: "fbdev"

[     4.928] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so

[     4.929] (II) Module fbdev: vendor="X.Org Foundation"

[     4.929]  compiled for 1.19.0, module version = 0.4.4

[     4.929]  Module class: X.Org Video Driver

[     4.929]  ABI class: X.Org Video Driver, version 23.0

[     4.929] (II) LoadModule: "vesa"

[     4.929] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so

[     4.930] (II) Module vesa: vendor="X.Org Foundation"

[     4.930]  compiled for 1.19.0, module version = 2.3.4

[     4.930]  Module class: X.Org Video Driver

[     4.930]  ABI class: X.Org Video Driver, version 23.0

[     4.930] (II) NOUVEAU driver Date:   Tue Sep 20 00:31:06 2016 -0400

[     4.930] (II) NOUVEAU driver for NVIDIA chipset families :

[     4.930]  RIVA TNT        (NV04)

[     4.930]  RIVA TNT2       (NV05)

[     4.930]  GeForce 256     (NV10)

[     4.930]  GeForce 2       (NV11, NV15)

[     4.930]  GeForce 4MX     (NV17, NV18)

[     4.930]  GeForce 3       (NV20)

[     4.930]  GeForce 4Ti     (NV25, NV28)

[     4.930]  GeForce FX      (NV3x)

[     4.930]  GeForce 6       (NV4x)

[     4.930]  GeForce 7       (G7x)

[     4.930]  GeForce 8       (G8x)

[     4.930]  GeForce GTX 200 (NVA0)

[     4.930]  GeForce GTX 400 (NVC0)

[     4.930] (II) modesetting: Driver for Modesetting Kernel Drivers: kms

[     4.930] (II) FBDEV: driver for framebuffer: fbdev

[     4.930] (II) VESA: driver for VESA chipsets: vesa

[     4.954] (II) [drm] nouveau interface version: 1.3.1

[     4.954] (EE) Unknown chipset: NV117

[     4.960] (II) modeset(0): using drv /dev/dri/card0

[     4.960] (II) modeset(G0): using drv /dev/dri/card1

[     4.960] (WW) Falling back to old probe method for fbdev

[     4.960] (II) Loading sub module "fbdevhw"

[     4.960] (II) LoadModule: "fbdevhw"

[     4.961] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so

[     4.961] (II) Module fbdevhw: vendor="X.Org Foundation"

[     4.961]  compiled for 1.19.2, module version = 0.0.2

[     4.961]  ABI class: X.Org Video Driver, version 23.0

[     4.961] (WW) Falling back to old probe method for vesa

[     4.961] (II) modeset(0): Creating default Display subsection in Screen section

  "Default Screen Section" for depth/fbbpp 24/32

[     4.961] (==) modeset(0): Depth 24, (==) framebuffer bpp 32

[     4.961] (==) modeset(0): RGB weight 888

[     4.961] (==) modeset(0): Default visual is TrueColor

[     4.961] (II) Loading sub module "glamoregl"

[     4.961] (II) LoadModule: "glamoregl"

[     4.962] (II) Loading /usr/lib/xorg/modules/libglamoregl.so

[     4.976] (II) Module glamoregl: vendor="X.Org Foundation"

[     4.976]  compiled for 1.19.2, module version = 1.0.0

[     4.976]  ABI class: X.Org ANSI C Emulation, version 0.4

[     4.976] (II) glamor: OpenGL accelerated X.org driver based.

[     5.018] (II) glamor: EGL version 1.4 (DRI2):

[     5.030] (II) modeset(0): glamor initialized

[     5.031] (II) modeset(0): Output eDP-1 has no monitor section

[     5.031] (II) modeset(0): Output DP-1 has no monitor section

[     5.154] (II) modeset(0): Output HDMI-1 has no monitor section

[     5.156] (II) modeset(0): Output HDMI-2 has no monitor section

[     5.156] (II) modeset(0): Output DP-2 has no monitor section

[     5.279] (II) modeset(0): Output HDMI-3 has no monitor section

[     5.280] (II) modeset(0): EDID for output eDP-1

[     5.280] (II) modeset(0): Manufacturer: AUO  Model: 38ed  Serial#: 0

[     5.280] (II) modeset(0): Year: 2014  Week: 43

[     5.280] (II) modeset(0): EDID Version: 1.4

[     5.280] (II) modeset(0): Digital Display Input

[     5.280] (II) modeset(0): 6 bits per channel

[     5.280] (II) modeset(0): Digital interface is DisplayPort

[     5.280] (II) modeset(0): Max Image Size [cm]: horiz.: 34  vert.: 19

[     5.280] (II) modeset(0): Gamma: 2.20

[     5.280] (II) modeset(0): No DPMS capabilities specified

[     5.280] (II) modeset(0): Supported color encodings: RGB 4:4:4 

[     5.280] (II) modeset(0): First detailed timing is preferred mode

[     5.280] (II) modeset(0): Preferred mode is native pixel format and refresh rate

[     5.280] (II) modeset(0): redX: 0.575 redY: 0.345   greenX: 0.340 greenY: 0.560

[     5.280] (II) modeset(0): blueX: 0.156 blueY: 0.123   whiteX: 0.313 whiteY: 0.329

[     5.280] (II) modeset(0): Manufacturer's mask: 0

[     5.280] (II) modeset(0): Supported detailed timing:

[     5.280] (II) modeset(0): clock: 142.0 MHz   Image Size:  344 x 193 mm

[     5.280] (II) modeset(0): h_active: 1920  h_sync: 2028  h_sync_end 2076 h_blank_end 2100 h_border: 0

[     5.280] (II) modeset(0): v_active: 1080  v_sync: 1090  v_sync_end 1100 v_blanking: 1126 v_border: 0

[     5.280] (II) modeset(0): Unknown vendor-specific block f

[     5.280] (II) modeset(0):  AUO

[     5.280] (II) modeset(0):  B156HTN03.8

[     5.280] (II) modeset(0): EDID (in hex):

[     5.280] (II) modeset(0):   00ffffffffffff0006afed3800000000

[     5.280] (II) modeset(0):   2b180104952213780251259358578f28

[     5.280] (II) modeset(0):   1f505400000001010101010101010101

[     5.280] (II) modeset(0):   010101010101783780b470382e406c30

[     5.280] (II) modeset(0):   aa0058c1100000180000000f00000000

[     5.280] (II) modeset(0):   00000000000000000020000000fe0041

[     5.280] (II) modeset(0):   554f0a202020202020202020000000fe

[     5.280] (II) modeset(0):   004231353648544e30332e38200a00e9

[     5.281] (II) modeset(0): Printing probed modes for output eDP-1

[     5.281] (II) modeset(0): Modeline "1920x1080"x60.1  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[     5.281] (II) modeset(0): Modeline "1920x1080"x59.9  138.50  1920 1968 2000 2080  1080 1083 1088 1111 +hsync -vsync (66.6 kHz d)

[     5.281] (II) modeset(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz d)

[     5.281] (II) modeset(0): Modeline "1680x1050"x59.9  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz d)

[     5.281] (II) modeset(0): Modeline "1600x1024"x60.2  103.12  1600 1600 1656 1664  1024 1024 1029 1030 +hsync +vsync (62.0 kHz d)

[     5.281] (II) modeset(0): Modeline "1400x1050"x60.0  122.00  1400 1488 1640 1880  1050 1052 1064 1082 +hsync +vsync (64.9 kHz d)

[     5.281] (II) modeset(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz d)

[     5.281] (II) modeset(0): Modeline "1440x900"x59.9  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz d)

[     5.281] (II) modeset(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz d)

[     5.281] (II) modeset(0): Modeline "1360x768"x59.8   84.75  1360 1432 1568 1776  768 771 781 798 -hsync +vsync (47.7 kHz d)

[     5.281] (II) modeset(0): Modeline "1360x768"x60.0   72.00  1360 1408 1440 1520  768 771 781 790 +hsync -vsync (47.4 kHz d)

[     5.281] (II) modeset(0): Modeline "1152x864"x60.0   81.62  1152 1216 1336 1520  864 865 868 895 -hsync +vsync (53.7 kHz d)

[     5.281] (II) modeset(0): Modeline "1024x768"x120.1  133.47  1024 1100 1212 1400  768 768 770 794 doublescan -hsync +vsync (95.3 kHz d)

[     5.281] (II) modeset(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz d)

[     5.281] (II) modeset(0): Modeline "960x720"x120.0  117.00  960 1024 1128 1300  720 720 722 750 doublescan -hsync +vsync (90.0 kHz d)

[     5.281] (II) modeset(0): Modeline "928x696"x120.1  109.15  928 976 1088 1264  696 696 698 719 doublescan -hsync +vsync (86.4 kHz d)

[     5.281] (II) modeset(0): Modeline "896x672"x120.0  102.40  896 960 1060 1224  672 672 674 697 doublescan -hsync +vsync (83.7 kHz d)

[     5.281] (II) modeset(0): Modeline "960x600"x120.0   77.00  960 984 1000 1040  600 601 604 617 doublescan +hsync -vsync (74.0 kHz d)

[     5.281] (II) modeset(0): Modeline "960x540"x120.0   69.25  960 984 1000 1040  540 541 544 555 doublescan +hsync -vsync (66.6 kHz d)

[     5.281] (II) modeset(0): Modeline "800x600"x120.0   81.00  800 832 928 1080  600 600 602 625 doublescan +hsync +vsync (75.0 kHz d)

[     5.281] (II) modeset(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz d)

[     5.281] (II) modeset(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz d)

[     5.281] (II) modeset(0): Modeline "840x525"x120.0   73.12  840 892 980 1120  525 526 529 544 doublescan -hsync +vsync (65.3 kHz d)

[     5.281] (II) modeset(0): Modeline "840x525"x119.8   59.50  840 864 880 920  525 526 529 540 doublescan +hsync -vsync (64.7 kHz d)

[     5.281] (II) modeset(0): Modeline "800x512"x120.3   51.56  800 800 828 832  512 512 514 515 doublescan +hsync +vsync (62.0 kHz d)

[     5.281] (II) modeset(0): Modeline "700x525"x120.0   61.00  700 744 820 940  525 526 532 541 doublescan +hsync +vsync (64.9 kHz d)

[     5.281] (II) modeset(0): Modeline "640x512"x120.0   54.00  640 664 720 844  512 512 514 533 doublescan +hsync +vsync (64.0 kHz d)

[     5.281] (II) modeset(0): Modeline "720x450"x119.8   53.25  720 760 836 952  450 451 454 467 doublescan -hsync +vsync (55.9 kHz d)

[     5.281] (II) modeset(0): Modeline "640x480"x120.0   54.00  640 688 744 900  480 480 482 500 doublescan +hsync +vsync (60.0 kHz d)

[     5.281] (II) modeset(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz d)

[     5.281] (II) modeset(0): Modeline "680x384"x119.6   42.38  680 716 784 888  384 385 390 399 doublescan -hsync +vsync (47.7 kHz d)

[     5.281] (II) modeset(0): Modeline "680x384"x119.9   36.00  680 704 720 760  384 385 390 395 doublescan +hsync -vsync (47.4 kHz d)

[     5.281] (II) modeset(0): Modeline "576x432"x120.1   40.81  576 608 668 760  432 432 434 447 doublescan -hsync +vsync (53.7 kHz d)

[     5.281] (II) modeset(0): Modeline "512x384"x120.0   32.50  512 524 592 672  384 385 388 403 doublescan -hsync -vsync (48.4 kHz d)

[     5.281] (II) modeset(0): Modeline "400x300"x120.6   20.00  400 420 484 528  300 300 302 314 doublescan +hsync +vsync (37.9 kHz d)

[     5.281] (II) modeset(0): Modeline "400x300"x112.7   18.00  400 412 448 512  300 300 301 312 doublescan +hsync +vsync (35.2 kHz d)

[     5.281] (II) modeset(0): Modeline "320x240"x120.1   12.59  320 328 376 400  240 245 246 262 doublescan -hsync -vsync (31.5 kHz d)

[     5.281] (II) modeset(0): EDID for output DP-1

[     5.402] (II) modeset(0): EDID for output HDMI-1

[     5.404] (II) modeset(0): EDID for output HDMI-2

[     5.404] (II) modeset(0): EDID for output DP-2

[     5.528] (II) modeset(0): EDID for output HDMI-3

[     5.528] (II) modeset(0): Output eDP-1 connected

[     5.528] (II) modeset(0): Output DP-1 disconnected

[     5.528] (II) modeset(0): Output HDMI-1 disconnected

[     5.528] (II) modeset(0): Output HDMI-2 disconnected

[     5.528] (II) modeset(0): Output DP-2 disconnected

[     5.528] (II) modeset(0): Output HDMI-3 disconnected

[     5.528] (II) modeset(0): Using exact sizes for initial modes

[     5.528] (II) modeset(0): Output eDP-1 using initial mode 1920x1080 +0+0

[     5.528] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)

[     5.528] (==) modeset(0): DPI set to (96, 96)

[     5.528] (II) Loading sub module "fb"

[     5.528] (II) LoadModule: "fb"

[     5.528] (II) Loading /usr/lib/xorg/modules/libfb.so

[     5.529] (II) Module fb: vendor="X.Org Foundation"

[     5.529]  compiled for 1.19.2, module version = 1.0.0

[     5.529]  ABI class: X.Org ANSI C Emulation, version 0.4

[     5.551] (==) modeset(G0): Depth 24, (==) framebuffer bpp 32

[     5.551] (==) modeset(G0): RGB weight 888

[     5.551] (==) modeset(G0): Default visual is TrueColor

[     5.551] (II) Loading sub module "glamoregl"

[     5.551] (II) LoadModule: "glamoregl"

[     5.551] (II) Loading /usr/lib/xorg/modules/libglamoregl.so

[     5.551] (II) Module glamoregl: vendor="X.Org Foundation"

[     5.551]  compiled for 1.19.2, module version = 1.0.0

[     5.551]  ABI class: X.Org ANSI C Emulation, version 0.4

[     5.551] (II) glamor: OpenGL accelerated X.org driver based.

[     5.861] (II) glamor: EGL version 1.4 (DRI2):

[     5.870] (II) modeset(G0): glamor initialized

[     5.870] (==) modeset(G0): Using gamma correction (1.0, 1.0, 1.0)

[     5.870] (==) modeset(G0): DPI set to (96, 96)

[     5.870] (II) Loading sub module "fb"

[     5.870] (II) LoadModule: "fb"

[     5.870] (II) Loading /usr/lib/xorg/modules/libfb.so

[     5.870] (II) Module fb: vendor="X.Org Foundation"

[     5.870]  compiled for 1.19.2, module version = 1.0.0

[     5.870]  ABI class: X.Org ANSI C Emulation, version 0.4

[     5.870] (II) UnloadModule: "fbdev"

[     5.870] (II) Unloading fbdev

[     5.870] (II) UnloadSubModule: "fbdevhw"

[     5.870] (II) Unloading fbdevhw

[     5.870] (II) UnloadModule: "vesa"

[     5.870] (II) Unloading vesa

[     5.870] (==) Depth 24 pixmap format is 32 bpp

[     5.919] (==) modeset(G0): Backing store enabled

[     5.919] (==) modeset(G0): Silken mouse enabled

[     5.920] (II) modeset(G0): RandR 1.2 enabled, ignore the following RandR disabled message.

[     5.920] (==) modeset(G0): DPMS enabled

[     5.920] (II) modeset(G0): [DRI2] Setup complete

[     5.920] (II) modeset(G0): [DRI2]   DRI driver: nouveau

[     5.920] (II) modeset(G0): [DRI2]   VDPAU driver: nouveau

[     5.987] (==) modeset(0): Backing store enabled

[     5.987] (==) modeset(0): Silken mouse enabled

[     5.987] (II) modeset(0): RandR 1.2 enabled, ignore the following RandR disabled message.

[     5.987] (==) modeset(0): DPMS enabled

[     5.987] (II) modeset(0): [DRI2] Setup complete

[     5.987] (II) modeset(0): [DRI2]   DRI driver: i965

[     5.987] (II) modeset(0): [DRI2]   VDPAU driver: i965

[     5.987] (--) RandR disabled

[     5.989] (II) SELinux: Disabled on system

[     5.993] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer

[     5.993] (II) AIGLX: enabled GLX_ARB_create_context

[     5.993] (II) AIGLX: enabled GLX_ARB_create_context_profile

[     5.993] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile

[     5.993] (II) AIGLX: enabled GLX_INTEL_swap_event

[     5.993] (II) AIGLX: enabled GLX_SGI_swap_control

[     5.993] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB

[     5.993] (II) AIGLX: enabled GLX_ARB_fbconfig_float

[     5.993] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float

[     5.993] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects

[     5.993] (II) AIGLX: enabled GLX_ARB_create_context_robustness

[     5.993] (II) AIGLX: Loaded and initialized i965

[     5.993] (II) GLX: Initialized DRI2 GL provider for screen 0

[     5.994] (II) modeset(G0): Damage tracking initialized

[     5.997] (II) modeset(0): Damage tracking initialized

[     5.997] (II) modeset(0): Setting screen physical size to 508 x 285

[     6.029] (II) config/udev: Adding input device Power Button (/dev/input/event3)

[     6.029] (**) Power Button: Applying InputClass "libinput keyboard catchall"

[     6.029] (II) LoadModule: "libinput"

[     6.029] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so

[     6.033] (II) Module libinput: vendor="X.Org Foundation"

[     6.033]  compiled for 1.19.0, module version = 0.23.0

[     6.033]  Module class: X.Org XInput Driver

[     6.033]  ABI class: X.Org XInput driver, version 24.1

[     6.033] (II) Using input driver 'libinput' for 'Power Button'

[     6.033] (**) Power Button: always reports core events

[     6.033] (**) Option "Device" "/dev/input/event3"

[     6.033] (**) Option "_source" "server/udev"

[     6.033] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard

[     6.033] (II) input device 'Power Button', /dev/input/event3 is a keyboard

[     6.052] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"

[     6.052] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)

[     6.052] (**) Option "xkb_model" "pc105"

[     6.052] (**) Option "xkb_layout" "fr"

[     6.052] (**) Option "xkb_variant" "latin9"

[     6.065] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard

[     6.065] (II) input device 'Power Button', /dev/input/event3 is a keyboard

[     6.065] (II) config/udev: Adding input device Asus Wireless Radio Control (/dev/input/event4)

[     6.065] (**) Asus Wireless Radio Control: Applying InputClass "libinput keyboard catchall"

[     6.065] (II) Using input driver 'libinput' for 'Asus Wireless Radio Control'

[     6.065] (**) Asus Wireless Radio Control: always reports core events

[     6.065] (**) Option "Device" "/dev/input/event4"

[     6.065] (**) Option "_source" "server/udev"

[     6.065] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is tagged by udev as: Keyboard

[     6.065] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is a keyboard

[     6.084] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/ATK4002:00/input/input4/event4"

[     6.084] (II) XINPUT: Adding extended input device "Asus Wireless Radio Control" (type: KEYBOARD, id 7)

[     6.084] (**) Option "xkb_model" "pc105"

[     6.084] (**) Option "xkb_layout" "fr"

[     6.084] (**) Option "xkb_variant" "latin9"

[     6.084] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is tagged by udev as: Keyboard

[     6.084] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is a keyboard

[     6.084] (II) config/udev: Adding input device Video Bus (/dev/input/event8)

[     6.084] (**) Video Bus: Applying InputClass "libinput keyboard catchall"

[     6.084] (II) Using input driver 'libinput' for 'Video Bus'

[     6.084] (**) Video Bus: always reports core events

[     6.084] (**) Option "Device" "/dev/input/event8"

[     6.084] (**) Option "_source" "server/udev"

[     6.085] (II) input device 'Video Bus', /dev/input/event8 is tagged by udev as: Keyboard

[     6.085] (II) input device 'Video Bus', /dev/input/event8 is a keyboard

[     6.100] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8/event8"

[     6.100] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)

[     6.100] (**) Option "xkb_model" "pc105"

[     6.100] (**) Option "xkb_layout" "fr"

[     6.100] (**) Option "xkb_variant" "latin9"

[     6.101] (II) input device 'Video Bus', /dev/input/event8 is tagged by udev as: Keyboard

[     6.101] (II) input device 'Video Bus', /dev/input/event8 is a keyboard

[     6.101] (II) config/udev: Adding input device Video Bus (/dev/input/event9)

[     6.101] (**) Video Bus: Applying InputClass "libinput keyboard catchall"

[     6.101] (II) Using input driver 'libinput' for 'Video Bus'

[     6.101] (**) Video Bus: always reports core events

[     6.101] (**) Option "Device" "/dev/input/event9"

[     6.101] (**) Option "_source" "server/udev"

[     6.102] (II) input device 'Video Bus', /dev/input/event9 is tagged by udev as: Keyboard

[     6.102] (II) input device 'Video Bus', /dev/input/event9 is a keyboard

[     6.116] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:12/LNXVIDEO:01/input/input9/event9"

[     6.116] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 9)

[     6.116] (**) Option "xkb_model" "pc105"

[     6.116] (**) Option "xkb_layout" "fr"

[     6.116] (**) Option "xkb_variant" "latin9"

[     6.117] (II) input device 'Video Bus', /dev/input/event9 is tagged by udev as: Keyboard

[     6.117] (II) input device 'Video Bus', /dev/input/event9 is a keyboard

[     6.117] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)

[     6.117] (II) No input driver specified, ignoring this device.

[     6.117] (II) This device may have been added with another device file.

[     6.118] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)

[     6.118] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"

[     6.118] (II) Using input driver 'libinput' for 'Sleep Button'

[     6.118] (**) Sleep Button: always reports core events

[     6.118] (**) Option "Device" "/dev/input/event2"

[     6.118] (**) Option "_source" "server/udev"

[     6.118] (II) input device 'Sleep Button', /dev/input/event2 is tagged by udev as: Keyboard

[     6.118] (II) input device 'Sleep Button', /dev/input/event2 is a keyboard

[     6.132] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2/event2"

[     6.132] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 10)

[     6.132] (**) Option "xkb_model" "pc105"

[     6.132] (**) Option "xkb_layout" "fr"

[     6.132] (**) Option "xkb_variant" "latin9"

[     6.133] (II) input device 'Sleep Button', /dev/input/event2 is tagged by udev as: Keyboard

[     6.133] (II) input device 'Sleep Button', /dev/input/event2 is a keyboard

[     6.134] (II) config/udev: Adding input device USB2.0 HD UVC WebCam (/dev/input/event6)

[     6.134] (**) USB2.0 HD UVC WebCam: Applying InputClass "libinput keyboard catchall"

[     6.134] (II) Using input driver 'libinput' for 'USB2.0 HD UVC WebCam'

[     6.134] (**) USB2.0 HD UVC WebCam: always reports core events

[     6.134] (**) Option "Device" "/dev/input/event6"

[     6.134] (**) Option "_source" "server/udev"

[     6.135] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is tagged by udev as: Keyboard

[     6.135] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is a keyboard

[     6.164] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/input/input6/event6"

[     6.164] (II) XINPUT: Adding extended input device "USB2.0 HD UVC WebCam" (type: KEYBOARD, id 11)

[     6.164] (**) Option "xkb_model" "pc105"

[     6.164] (**) Option "xkb_layout" "fr"

[     6.164] (**) Option "xkb_variant" "latin9"

[     6.165] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is tagged by udev as: Keyboard

[     6.165] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is a keyboard

[     6.165] (II) config/udev: Adding input device Elan Touchpad (/dev/input/event10)

[     6.165] (**) Elan Touchpad: Applying InputClass "libinput touchpad catchall"

[     6.165] (II) Using input driver 'libinput' for 'Elan Touchpad'

[     6.165] (**) Elan Touchpad: always reports core events

[     6.165] (**) Option "Device" "/dev/input/event10"

[     6.165] (**) Option "_source" "server/udev"

[     6.166] (II) input device 'Elan Touchpad', /dev/input/event10 is tagged by udev as: Touchpad

[     6.166] (II) input device 'Elan Touchpad', /dev/input/event10 is a touchpad

[     6.196] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-20/i2c-ELAN1000:00/input/input10/event10"

[     6.196] (II) XINPUT: Adding extended input device "Elan Touchpad" (type: TOUCHPAD, id 12)

[     6.196] (**) Option "AccelerationScheme" "none"

[     6.196] (**) Elan Touchpad: (accel) selected scheme none/0

[     6.196] (**) Elan Touchpad: (accel) acceleration factor: 2.000

[     6.196] (**) Elan Touchpad: (accel) acceleration threshold: 4

[     6.197] (II) input device 'Elan Touchpad', /dev/input/event10 is tagged by udev as: Touchpad

[     6.197] (II) input device 'Elan Touchpad', /dev/input/event10 is a touchpad

[     6.198] (II) config/udev: Adding input device Elan Touchpad (/dev/input/mouse0)

[     6.198] (II) No input driver specified, ignoring this device.

[     6.198] (II) This device may have been added with another device file.

[     6.198] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event11)

[     6.198] (II) No input driver specified, ignoring this device.

[     6.198] (II) This device may have been added with another device file.

[     6.199] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event12)

[     6.199] (II) No input driver specified, ignoring this device.

[     6.199] (II) This device may have been added with another device file.

[     6.199] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event13)

[     6.199] (II) No input driver specified, ignoring this device.

[     6.199] (II) This device may have been added with another device file.

[     6.199] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event14)

[     6.199] (II) No input driver specified, ignoring this device.

[     6.199] (II) This device may have been added with another device file.

[     6.200] (II) config/udev: Adding input device Asus WMI hotkeys (/dev/input/event7)

[     6.200] (**) Asus WMI hotkeys: Applying InputClass "libinput keyboard catchall"

[     6.200] (II) Using input driver 'libinput' for 'Asus WMI hotkeys'

[     6.200] (**) Asus WMI hotkeys: always reports core events

[     6.200] (**) Option "Device" "/dev/input/event7"

[     6.200] (**) Option "_source" "server/udev"

[     6.201] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is tagged by udev as: Keyboard

[     6.201] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is a keyboard

[     6.224] (**) Option "config_info" "udev:/sys/devices/platform/asus-nb-wmi/input/input7/event7"

[     6.224] (II) XINPUT: Adding extended input device "Asus WMI hotkeys" (type: KEYBOARD, id 13)

[     6.224] (**) Option "xkb_model" "pc105"

[     6.224] (**) Option "xkb_layout" "fr"

[     6.224] (**) Option "xkb_variant" "latin9"

[     6.225] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is tagged by udev as: Keyboard

[     6.225] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is a keyboard

[     6.225] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)

[     6.225] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"

[     6.225] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'

[     6.225] (**) AT Translated Set 2 keyboard: always reports core events

[     6.225] (**) Option "Device" "/dev/input/event0"

[     6.225] (**) Option "_source" "server/udev"

[     6.226] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard

[     6.226] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard

[     6.256] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"

[     6.256] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 14)

[     6.256] (**) Option "xkb_model" "pc105"

[     6.256] (**) Option "xkb_layout" "fr"

[     6.256] (**) Option "xkb_variant" "latin9"

[     6.257] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard

[     6.257] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard

[     6.257] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)

[     6.257] (II) No input driver specified, ignoring this device.

[     6.257] (II) This device may have been added with another device file.

[    35.842] (II) modeset(0): EDID vendor "AUO", prod id 14573

[    35.842] (II) modeset(0): Printing DDC gathered Modelines:

[    35.842] (II) modeset(0): Modeline "1920x1080"x0.0  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[    36.091] (II) modeset(0): EDID vendor "AUO", prod id 14573

[    36.091] (II) modeset(0): Printing DDC gathered Modelines:

[    36.091] (II) modeset(0): Modeline "1920x1080"x0.0  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[    36.343] (II) modeset(0): EDID vendor "AUO", prod id 14573

[    36.343] (II) modeset(0): Printing DDC gathered Modelines:

[    36.343] (II) modeset(0): Modeline "1920x1080"x0.0  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[    36.592] (II) modeset(0): EDID vendor "AUO", prod id 14573

[    36.593] (II) modeset(0): Printing DDC gathered Modelines:

[    36.593] (II) modeset(0): Modeline "1920x1080"x0.0  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

anonyme · 05-04-2017 01:47:19

la position matérielle de tes cartes vidéo

[     4.896] (II) xfree86: Adding drm device (/dev/dri/card1)

[     4.897] (II) xfree86: Adding drm device (/dev/dri/card0)

[     4.912] (--) PCI:*(0:0:2:0) 8086:191b:1043:1c5d rev 6, Mem @ 0xdd000000/16777216, 0xb0000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072

[     4.912] (--) PCI: (0:1:0:0) 10de:139b:1043:1c5d rev 162, Mem @ 0xde000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288

le travail de kms pour "nouveau" et "intel" DRI2

[     5.920] (II) modeset(G0): [DRI2] Setup complete

[     5.920] (II) modeset(G0): [DRI2]   DRI driver: nouveau

[     5.920] (II) modeset(G0): [DRI2]   VDPAU driver: nouveau

[     5.987] (==) modeset(0): Backing store enabled

[     5.987] (==) modeset(0): Silken mouse enabled

[     5.987] (II) modeset(0): RandR 1.2 enabled, ignore the following RandR disabled message.

[     5.987] (==) modeset(0): DPMS enabled

[     5.987] (II) modeset(0): [DRI2] Setup complete

[     5.987] (II) modeset(0): [DRI2]   DRI driver: i965

[     5.987] (II) modeset(0): [DRI2]   VDPAU driver: i965

l init GLX pour intel

[     5.993] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer

[     5.993] (II) AIGLX: enabled GLX_ARB_create_context

[     5.993] (II) AIGLX: enabled GLX_ARB_create_context_profile

[     5.993] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile

[     5.993] (II) AIGLX: enabled GLX_INTEL_swap_event

[     5.993] (II) AIGLX: enabled GLX_SGI_swap_control

[     5.993] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB

[     5.993] (II) AIGLX: enabled GLX_ARB_fbconfig_float

[     5.993] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float

[     5.993] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects

[     5.993] (II) AIGLX: enabled GLX_ARB_create_context_robustness

[     5.993] (II) AIGLX: Loaded and initialized i965

[     5.993] (II) GLX: Initialized DRI2 GL provider for screen 0

donc on est bien d'accord tu a supprimé le "xserver-xorg-video-nouveau" et "xserver-xorg-video-intel" ?

vérifier le paquet présent "firmware-misc-nonfree"

apt-get --reinstall install firmware-misc-nonfree

 

nota: ce paquet permet de mieux utiliser kabylake pour intel ( et peut etre aussi ton nvidia avec nouveau sous réserve jamais testé)
un reboot

essaie de te logger sur ton bureau gnome (pas sur qu il fonctionne avec lightdm )

si j ai rien oublié , tu a un driver ok pour intel , demain tu aura surement des réponses pour bumblebee ( et comment bien l installer je suppose avec le driver propriétaire des dépots )

si gnome ne se lance pas il y a surement encore un souci (mais je pense qu il va fonctionner ) si tu enlève mate pense aussi a enlever lightdm pour revenir a gdm3 qui est le lanceur officiel de gnome

je te conseille si gnome est OK , de juste enlever lightdm :

apt-get remove lightdm

 

redémarrer avec gdm3 + gnome
de nettoyer mate tranquillement avec synaptic par la suite (mate-core est trés léger )

Dernière modification par anonyme (05-04-2017 02:11:51)

Manahoar · 05-04-2017 02:14:06

Ah je n'ai pas vu que tu avais EDIT ton message précédent où tu me demandais de purger "xserver-xorg-video-nouveau" et "xserver-xorg-video-intel". Du coup je te renvois les logs on ne sait jamais

 /var/log/Xorg.0.log

[     5.187] 

X.Org X Server 1.19.2

Release Date: 2017-03-02

[     5.187] X Protocol Version 11, Revision 0

[     5.187] Build Operating System: Linux 3.16.0-4-amd64 x86_64 Debian

[     5.187] Current Operating System: Linux debian-mnhr 4.9.0-2-amd64 #1 SMP Debian 4.9.13-1 (2017-02-27) x86_64

[     5.187] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-2-amd64 root=UUID=d11a650c-29a7-47bc-99af-e1b4de5522ea ro quiet

[     5.187] Build Date: 03 March 2017  03:14:41PM

[     5.187] xorg-server 2:1.19.2-1 (https://www.debian.org/support) 

[     5.187] Current version of pixman: 0.34.0

[     5.187]  Before reporting problems, check http://wiki.x.org

  to make sure that you have the latest version.

[     5.187] Markers: (--) probed, (**) from config file, (==) default setting,

  (++) from command line, (!!) notice, (II) informational,

  (WW) warning, (EE) error, (NI) not implemented, (??) unknown.

[     5.187] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Apr  5 02:54:57 2017

[     5.189] (==) Using system config directory "/usr/share/X11/xorg.conf.d"

[     5.190] (==) No Layout section.  Using the first Screen section.

[     5.190] (==) No screen section available. Using defaults.

[     5.190] (**) |-->Screen "Default Screen Section" (0)

[     5.190] (**) |   |-->Monitor "<default monitor>"

[     5.190] (==) No monitor specified for screen "Default Screen Section".

  Using a default monitor configuration.

[     5.190] (==) Automatically adding devices

[     5.190] (==) Automatically enabling devices

[     5.190] (==) Automatically adding GPU devices

[     5.190] (==) Max clients allowed: 256, resource mask: 0x1fffff

[     5.192] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.

[     5.192]  Entry deleted from font path.

[     5.192] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.

[     5.192]  Entry deleted from font path.

[     5.192] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.

[     5.192]  Entry deleted from font path.

[     5.192] (WW) The directory "/usr/share/fonts/X11/Type1" does not exist.

[     5.192]  Entry deleted from font path.

[     5.192] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.

[     5.192]  Entry deleted from font path.

[     5.192] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.

[     5.192]  Entry deleted from font path.

[     5.192] (==) FontPath set to:

  /usr/share/fonts/X11/misc,

  built-ins

[     5.192] (==) ModulePath set to "/usr/lib/xorg/modules"

[     5.192] (II) The server relies on udev to provide the list of input devices.

  If no devices become available, reconfigure udev or disable AutoAddDevices.

[     5.192] (II) Loader magic: 0x563909d3ce00

[     5.192] (II) Module ABI versions:

[     5.192]  X.Org ANSI C Emulation: 0.4

[     5.192]  X.Org Video Driver: 23.0

[     5.192]  X.Org XInput driver : 24.1

[     5.192]  X.Org Server Extension : 10.0

[     5.193] (++) using VT number 7

[     5.193] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration

[     5.194] (II) xfree86: Adding drm device (/dev/dri/card1)

[     5.194] (II) xfree86: Adding drm device (/dev/dri/card0)

[     5.204] (--) PCI:*(0:0:2:0) 8086:191b:1043:1c5d rev 6, Mem @ 0xdd000000/16777216, 0xb0000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072

[     5.204] (--) PCI: (0:1:0:0) 10de:139b:1043:1c5d rev 162, Mem @ 0xde000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288

[     5.204] (II) LoadModule: "glx"

[     5.206] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so

[     5.215] (II) Module glx: vendor="X.Org Foundation"

[     5.215]  compiled for 1.19.2, module version = 1.0.0

[     5.215]  ABI class: X.Org Server Extension, version 10.0

[     5.215] (==) Matched nouveau as autoconfigured driver 0

[     5.215] (==) Matched nv as autoconfigured driver 1

[     5.215] (==) Matched modesetting as autoconfigured driver 2

[     5.215] (==) Matched fbdev as autoconfigured driver 3

[     5.216] (==) Matched vesa as autoconfigured driver 4

[     5.216] (==) Assigned the driver to the xf86ConfigLayout

[     5.216] (II) LoadModule: "nouveau"

[     5.216] (WW) Warning, couldn't open module nouveau

[     5.216] (II) UnloadModule: "nouveau"

[     5.216] (II) Unloading nouveau

[     5.216] (EE) Failed to load module "nouveau" (module does not exist, 0)

[     5.216] (II) LoadModule: "nv"

[     5.216] (WW) Warning, couldn't open module nv

[     5.216] (II) UnloadModule: "nv"

[     5.216] (II) Unloading nv

[     5.216] (EE) Failed to load module "nv" (module does not exist, 0)

[     5.216] (II) LoadModule: "modesetting"

[     5.216] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so

[     5.217] (II) Module modesetting: vendor="X.Org Foundation"

[     5.217]  compiled for 1.19.2, module version = 1.19.2

[     5.217]  Module class: X.Org Video Driver

[     5.217]  ABI class: X.Org Video Driver, version 23.0

[     5.217] (II) LoadModule: "fbdev"

[     5.217] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so

[     5.217] (II) Module fbdev: vendor="X.Org Foundation"

[     5.217]  compiled for 1.19.0, module version = 0.4.4

[     5.217]  Module class: X.Org Video Driver

[     5.217]  ABI class: X.Org Video Driver, version 23.0

[     5.217] (II) LoadModule: "vesa"

[     5.217] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so

[     5.218] (II) Module vesa: vendor="X.Org Foundation"

[     5.218]  compiled for 1.19.0, module version = 2.3.4

[     5.218]  Module class: X.Org Video Driver

[     5.218]  ABI class: X.Org Video Driver, version 23.0

[     5.218] (II) modesetting: Driver for Modesetting Kernel Drivers: kms

[     5.218] (II) FBDEV: driver for framebuffer: fbdev

[     5.218] (II) VESA: driver for VESA chipsets: vesa

[     5.236] (II) modeset(0): using drv /dev/dri/card0

[     5.236] (II) modeset(G0): using drv /dev/dri/card1

[     5.236] (WW) Falling back to old probe method for fbdev

[     5.236] (II) Loading sub module "fbdevhw"

[     5.236] (II) LoadModule: "fbdevhw"

[     5.237] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so

[     5.237] (II) Module fbdevhw: vendor="X.Org Foundation"

[     5.237]  compiled for 1.19.2, module version = 0.0.2

[     5.237]  ABI class: X.Org Video Driver, version 23.0

[     5.237] (WW) Falling back to old probe method for vesa

[     5.237] (II) modeset(0): Creating default Display subsection in Screen section

  "Default Screen Section" for depth/fbbpp 24/32

[     5.237] (==) modeset(0): Depth 24, (==) framebuffer bpp 32

[     5.237] (==) modeset(0): RGB weight 888

[     5.237] (==) modeset(0): Default visual is TrueColor

[     5.238] (II) Loading sub module "glamoregl"

[     5.238] (II) LoadModule: "glamoregl"

[     5.238] (II) Loading /usr/lib/xorg/modules/libglamoregl.so

[     5.252] (II) Module glamoregl: vendor="X.Org Foundation"

[     5.252]  compiled for 1.19.2, module version = 1.0.0

[     5.252]  ABI class: X.Org ANSI C Emulation, version 0.4

[     5.252] (II) glamor: OpenGL accelerated X.org driver based.

[     5.292] (II) glamor: EGL version 1.4 (DRI2):

[     5.306] (II) modeset(0): glamor initialized

[     5.306] (II) modeset(0): Output eDP-1 has no monitor section

[     5.307] (II) modeset(0): Output DP-1 has no monitor section

[     5.430] (II) modeset(0): Output HDMI-1 has no monitor section

[     5.432] (II) modeset(0): Output HDMI-2 has no monitor section

[     5.432] (II) modeset(0): Output DP-2 has no monitor section

[     5.560] (II) modeset(0): Output HDMI-3 has no monitor section

[     5.561] (II) modeset(0): EDID for output eDP-1

[     5.561] (II) modeset(0): Manufacturer: AUO  Model: 38ed  Serial#: 0

[     5.561] (II) modeset(0): Year: 2014  Week: 43

[     5.561] (II) modeset(0): EDID Version: 1.4

[     5.561] (II) modeset(0): Digital Display Input

[     5.561] (II) modeset(0): 6 bits per channel

[     5.561] (II) modeset(0): Digital interface is DisplayPort

[     5.561] (II) modeset(0): Max Image Size [cm]: horiz.: 34  vert.: 19

[     5.561] (II) modeset(0): Gamma: 2.20

[     5.561] (II) modeset(0): No DPMS capabilities specified

[     5.561] (II) modeset(0): Supported color encodings: RGB 4:4:4 

[     5.561] (II) modeset(0): First detailed timing is preferred mode

[     5.561] (II) modeset(0): Preferred mode is native pixel format and refresh rate

[     5.561] (II) modeset(0): redX: 0.575 redY: 0.345   greenX: 0.340 greenY: 0.560

[     5.561] (II) modeset(0): blueX: 0.156 blueY: 0.123   whiteX: 0.313 whiteY: 0.329

[     5.561] (II) modeset(0): Manufacturer's mask: 0

[     5.561] (II) modeset(0): Supported detailed timing:

[     5.561] (II) modeset(0): clock: 142.0 MHz   Image Size:  344 x 193 mm

[     5.561] (II) modeset(0): h_active: 1920  h_sync: 2028  h_sync_end 2076 h_blank_end 2100 h_border: 0

[     5.561] (II) modeset(0): v_active: 1080  v_sync: 1090  v_sync_end 1100 v_blanking: 1126 v_border: 0

[     5.561] (II) modeset(0): Unknown vendor-specific block f

[     5.561] (II) modeset(0):  AUO

[     5.561] (II) modeset(0):  B156HTN03.8

[     5.561] (II) modeset(0): EDID (in hex):

[     5.561] (II) modeset(0):   00ffffffffffff0006afed3800000000

[     5.561] (II) modeset(0):   2b180104952213780251259358578f28

[     5.561] (II) modeset(0):   1f505400000001010101010101010101

[     5.561] (II) modeset(0):   010101010101783780b470382e406c30

[     5.561] (II) modeset(0):   aa0058c1100000180000000f00000000

[     5.561] (II) modeset(0):   00000000000000000020000000fe0041

[     5.561] (II) modeset(0):   554f0a202020202020202020000000fe

[     5.561] (II) modeset(0):   004231353648544e30332e38200a00e9

[     5.561] (II) modeset(0): Printing probed modes for output eDP-1

[     5.561] (II) modeset(0): Modeline "1920x1080"x60.1  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[     5.561] (II) modeset(0): Modeline "1920x1080"x59.9  138.50  1920 1968 2000 2080  1080 1083 1088 1111 +hsync -vsync (66.6 kHz d)

[     5.561] (II) modeset(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz d)

[     5.561] (II) modeset(0): Modeline "1680x1050"x59.9  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz d)

[     5.561] (II) modeset(0): Modeline "1600x1024"x60.2  103.12  1600 1600 1656 1664  1024 1024 1029 1030 +hsync +vsync (62.0 kHz d)

[     5.561] (II) modeset(0): Modeline "1400x1050"x60.0  122.00  1400 1488 1640 1880  1050 1052 1064 1082 +hsync +vsync (64.9 kHz d)

[     5.561] (II) modeset(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz d)

[     5.561] (II) modeset(0): Modeline "1440x900"x59.9  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz d)

[     5.561] (II) modeset(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz d)

[     5.561] (II) modeset(0): Modeline "1360x768"x59.8   84.75  1360 1432 1568 1776  768 771 781 798 -hsync +vsync (47.7 kHz d)

[     5.561] (II) modeset(0): Modeline "1360x768"x60.0   72.00  1360 1408 1440 1520  768 771 781 790 +hsync -vsync (47.4 kHz d)

[     5.561] (II) modeset(0): Modeline "1152x864"x60.0   81.62  1152 1216 1336 1520  864 865 868 895 -hsync +vsync (53.7 kHz d)

[     5.561] (II) modeset(0): Modeline "1024x768"x120.1  133.47  1024 1100 1212 1400  768 768 770 794 doublescan -hsync +vsync (95.3 kHz d)

[     5.561] (II) modeset(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz d)

[     5.561] (II) modeset(0): Modeline "960x720"x120.0  117.00  960 1024 1128 1300  720 720 722 750 doublescan -hsync +vsync (90.0 kHz d)

[     5.561] (II) modeset(0): Modeline "928x696"x120.1  109.15  928 976 1088 1264  696 696 698 719 doublescan -hsync +vsync (86.4 kHz d)

[     5.561] (II) modeset(0): Modeline "896x672"x120.0  102.40  896 960 1060 1224  672 672 674 697 doublescan -hsync +vsync (83.7 kHz d)

[     5.561] (II) modeset(0): Modeline "960x600"x120.0   77.00  960 984 1000 1040  600 601 604 617 doublescan +hsync -vsync (74.0 kHz d)

[     5.561] (II) modeset(0): Modeline "960x540"x120.0   69.25  960 984 1000 1040  540 541 544 555 doublescan +hsync -vsync (66.6 kHz d)

[     5.562] (II) modeset(0): Modeline "800x600"x120.0   81.00  800 832 928 1080  600 600 602 625 doublescan +hsync +vsync (75.0 kHz d)

[     5.562] (II) modeset(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz d)

[     5.562] (II) modeset(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz d)

[     5.562] (II) modeset(0): Modeline "840x525"x120.0   73.12  840 892 980 1120  525 526 529 544 doublescan -hsync +vsync (65.3 kHz d)

[     5.562] (II) modeset(0): Modeline "840x525"x119.8   59.50  840 864 880 920  525 526 529 540 doublescan +hsync -vsync (64.7 kHz d)

[     5.562] (II) modeset(0): Modeline "800x512"x120.3   51.56  800 800 828 832  512 512 514 515 doublescan +hsync +vsync (62.0 kHz d)

[     5.562] (II) modeset(0): Modeline "700x525"x120.0   61.00  700 744 820 940  525 526 532 541 doublescan +hsync +vsync (64.9 kHz d)

[     5.562] (II) modeset(0): Modeline "640x512"x120.0   54.00  640 664 720 844  512 512 514 533 doublescan +hsync +vsync (64.0 kHz d)

[     5.562] (II) modeset(0): Modeline "720x450"x119.8   53.25  720 760 836 952  450 451 454 467 doublescan -hsync +vsync (55.9 kHz d)

[     5.562] (II) modeset(0): Modeline "640x480"x120.0   54.00  640 688 744 900  480 480 482 500 doublescan +hsync +vsync (60.0 kHz d)

[     5.562] (II) modeset(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz d)

[     5.562] (II) modeset(0): Modeline "680x384"x119.6   42.38  680 716 784 888  384 385 390 399 doublescan -hsync +vsync (47.7 kHz d)

[     5.562] (II) modeset(0): Modeline "680x384"x119.9   36.00  680 704 720 760  384 385 390 395 doublescan +hsync -vsync (47.4 kHz d)

[     5.562] (II) modeset(0): Modeline "576x432"x120.1   40.81  576 608 668 760  432 432 434 447 doublescan -hsync +vsync (53.7 kHz d)

[     5.562] (II) modeset(0): Modeline "512x384"x120.0   32.50  512 524 592 672  384 385 388 403 doublescan -hsync -vsync (48.4 kHz d)

[     5.562] (II) modeset(0): Modeline "400x300"x120.6   20.00  400 420 484 528  300 300 302 314 doublescan +hsync +vsync (37.9 kHz d)

[     5.562] (II) modeset(0): Modeline "400x300"x112.7   18.00  400 412 448 512  300 300 301 312 doublescan +hsync +vsync (35.2 kHz d)

[     5.562] (II) modeset(0): Modeline "320x240"x120.1   12.59  320 328 376 400  240 245 246 262 doublescan -hsync -vsync (31.5 kHz d)

[     5.562] (II) modeset(0): EDID for output DP-1

[     5.686] (II) modeset(0): EDID for output HDMI-1

[     5.688] (II) modeset(0): EDID for output HDMI-2

[     5.688] (II) modeset(0): EDID for output DP-2

[     5.811] (II) modeset(0): EDID for output HDMI-3

[     5.811] (II) modeset(0): Output eDP-1 connected

[     5.811] (II) modeset(0): Output DP-1 disconnected

[     5.811] (II) modeset(0): Output HDMI-1 disconnected

[     5.811] (II) modeset(0): Output HDMI-2 disconnected

[     5.811] (II) modeset(0): Output DP-2 disconnected

[     5.811] (II) modeset(0): Output HDMI-3 disconnected

[     5.811] (II) modeset(0): Using exact sizes for initial modes

[     5.811] (II) modeset(0): Output eDP-1 using initial mode 1920x1080 +0+0

[     5.811] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)

[     5.811] (==) modeset(0): DPI set to (96, 96)

[     5.811] (II) Loading sub module "fb"

[     5.811] (II) LoadModule: "fb"

[     5.811] (II) Loading /usr/lib/xorg/modules/libfb.so

[     5.812] (II) Module fb: vendor="X.Org Foundation"

[     5.812]  compiled for 1.19.2, module version = 1.0.0

[     5.812]  ABI class: X.Org ANSI C Emulation, version 0.4

[     5.835] (==) modeset(G0): Depth 24, (==) framebuffer bpp 32

[     5.835] (==) modeset(G0): RGB weight 888

[     5.835] (==) modeset(G0): Default visual is TrueColor

[     5.835] (II) Loading sub module "glamoregl"

[     5.835] (II) LoadModule: "glamoregl"

[     5.835] (II) Loading /usr/lib/xorg/modules/libglamoregl.so

[     5.835] (II) Module glamoregl: vendor="X.Org Foundation"

[     5.835]  compiled for 1.19.2, module version = 1.0.0

[     5.835]  ABI class: X.Org ANSI C Emulation, version 0.4

[     5.835] (II) glamor: OpenGL accelerated X.org driver based.

[     6.127] (II) glamor: EGL version 1.4 (DRI2):

[     6.138] (II) modeset(G0): glamor initialized

[     6.138] (==) modeset(G0): Using gamma correction (1.0, 1.0, 1.0)

[     6.138] (==) modeset(G0): DPI set to (96, 96)

[     6.138] (II) Loading sub module "fb"

[     6.138] (II) LoadModule: "fb"

[     6.138] (II) Loading /usr/lib/xorg/modules/libfb.so

[     6.138] (II) Module fb: vendor="X.Org Foundation"

[     6.138]  compiled for 1.19.2, module version = 1.0.0

[     6.138]  ABI class: X.Org ANSI C Emulation, version 0.4

[     6.138] (II) UnloadModule: "fbdev"

[     6.138] (II) Unloading fbdev

[     6.138] (II) UnloadSubModule: "fbdevhw"

[     6.138] (II) Unloading fbdevhw

[     6.138] (II) UnloadModule: "vesa"

[     6.138] (II) Unloading vesa

[     6.138] (==) Depth 24 pixmap format is 32 bpp

[     6.223] (==) modeset(G0): Backing store enabled

[     6.223] (==) modeset(G0): Silken mouse enabled

[     6.223] (II) modeset(G0): RandR 1.2 enabled, ignore the following RandR disabled message.

[     6.224] (==) modeset(G0): DPMS enabled

[     6.224] (II) modeset(G0): [DRI2] Setup complete

[     6.224] (II) modeset(G0): [DRI2]   DRI driver: nouveau

[     6.224] (II) modeset(G0): [DRI2]   VDPAU driver: nouveau

[     6.292] (==) modeset(0): Backing store enabled

[     6.292] (==) modeset(0): Silken mouse enabled

[     6.292] (II) modeset(0): RandR 1.2 enabled, ignore the following RandR disabled message.

[     6.292] (==) modeset(0): DPMS enabled

[     6.292] (II) modeset(0): [DRI2] Setup complete

[     6.292] (II) modeset(0): [DRI2]   DRI driver: i965

[     6.292] (II) modeset(0): [DRI2]   VDPAU driver: i965

[     6.292] (--) RandR disabled

[     6.294] (II) SELinux: Disabled on system

[     6.298] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer

[     6.298] (II) AIGLX: enabled GLX_ARB_create_context

[     6.298] (II) AIGLX: enabled GLX_ARB_create_context_profile

[     6.298] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile

[     6.298] (II) AIGLX: enabled GLX_INTEL_swap_event

[     6.298] (II) AIGLX: enabled GLX_SGI_swap_control

[     6.298] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB

[     6.298] (II) AIGLX: enabled GLX_ARB_fbconfig_float

[     6.298] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float

[     6.298] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects

[     6.298] (II) AIGLX: enabled GLX_ARB_create_context_robustness

[     6.298] (II) AIGLX: Loaded and initialized i965

[     6.298] (II) GLX: Initialized DRI2 GL provider for screen 0

[     6.300] (II) modeset(G0): Damage tracking initialized

[     6.302] (II) modeset(0): Damage tracking initialized

[     6.302] (II) modeset(0): Setting screen physical size to 508 x 285

[     6.334] (II) config/udev: Adding input device Power Button (/dev/input/event4)

[     6.334] (**) Power Button: Applying InputClass "libinput keyboard catchall"

[     6.334] (II) LoadModule: "libinput"

[     6.334] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so

[     6.338] (II) Module libinput: vendor="X.Org Foundation"

[     6.338]  compiled for 1.19.0, module version = 0.23.0

[     6.338]  Module class: X.Org XInput Driver

[     6.338]  ABI class: X.Org XInput driver, version 24.1

[     6.338] (II) Using input driver 'libinput' for 'Power Button'

[     6.338] (**) Power Button: always reports core events

[     6.338] (**) Option "Device" "/dev/input/event4"

[     6.339] (**) Option "_source" "server/udev"

[     6.339] (II) input device 'Power Button', /dev/input/event4 is tagged by udev as: Keyboard

[     6.339] (II) input device 'Power Button', /dev/input/event4 is a keyboard

[     6.360] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event4"

[     6.360] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)

[     6.360] (**) Option "xkb_model" "pc105"

[     6.360] (**) Option "xkb_layout" "fr"

[     6.360] (**) Option "xkb_variant" "latin9"

[     6.374] (II) input device 'Power Button', /dev/input/event4 is tagged by udev as: Keyboard

[     6.374] (II) input device 'Power Button', /dev/input/event4 is a keyboard

[     6.374] (II) config/udev: Adding input device Asus Wireless Radio Control (/dev/input/event2)

[     6.374] (**) Asus Wireless Radio Control: Applying InputClass "libinput keyboard catchall"

[     6.374] (II) Using input driver 'libinput' for 'Asus Wireless Radio Control'

[     6.374] (**) Asus Wireless Radio Control: always reports core events

[     6.374] (**) Option "Device" "/dev/input/event2"

[     6.374] (**) Option "_source" "server/udev"

[     6.374] (II) input device 'Asus Wireless Radio Control', /dev/input/event2 is tagged by udev as: Keyboard

[     6.374] (II) input device 'Asus Wireless Radio Control', /dev/input/event2 is a keyboard

[     6.392] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/ATK4002:00/input/input2/event2"

[     6.392] (II) XINPUT: Adding extended input device "Asus Wireless Radio Control" (type: KEYBOARD, id 7)

[     6.392] (**) Option "xkb_model" "pc105"

[     6.392] (**) Option "xkb_layout" "fr"

[     6.392] (**) Option "xkb_variant" "latin9"

[     6.392] (II) input device 'Asus Wireless Radio Control', /dev/input/event2 is tagged by udev as: Keyboard

[     6.392] (II) input device 'Asus Wireless Radio Control', /dev/input/event2 is a keyboard

[     6.393] (II) config/udev: Adding input device Video Bus (/dev/input/event8)

[     6.393] (**) Video Bus: Applying InputClass "libinput keyboard catchall"

[     6.393] (II) Using input driver 'libinput' for 'Video Bus'

[     6.393] (**) Video Bus: always reports core events

[     6.393] (**) Option "Device" "/dev/input/event8"

[     6.393] (**) Option "_source" "server/udev"

[     6.393] (II) input device 'Video Bus', /dev/input/event8 is tagged by udev as: Keyboard

[     6.393] (II) input device 'Video Bus', /dev/input/event8 is a keyboard

[     6.408] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8/event8"

[     6.408] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)

[     6.408] (**) Option "xkb_model" "pc105"

[     6.408] (**) Option "xkb_layout" "fr"

[     6.408] (**) Option "xkb_variant" "latin9"

[     6.409] (II) input device 'Video Bus', /dev/input/event8 is tagged by udev as: Keyboard

[     6.409] (II) input device 'Video Bus', /dev/input/event8 is a keyboard

[     6.409] (II) config/udev: Adding input device Video Bus (/dev/input/event9)

[     6.409] (**) Video Bus: Applying InputClass "libinput keyboard catchall"

[     6.409] (II) Using input driver 'libinput' for 'Video Bus'

[     6.409] (**) Video Bus: always reports core events

[     6.409] (**) Option "Device" "/dev/input/event9"

[     6.410] (**) Option "_source" "server/udev"

[     6.410] (II) input device 'Video Bus', /dev/input/event9 is tagged by udev as: Keyboard

[     6.410] (II) input device 'Video Bus', /dev/input/event9 is a keyboard

[     6.424] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:12/LNXVIDEO:01/input/input9/event9"

[     6.424] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 9)

[     6.424] (**) Option "xkb_model" "pc105"

[     6.424] (**) Option "xkb_layout" "fr"

[     6.424] (**) Option "xkb_variant" "latin9"

[     6.425] (II) input device 'Video Bus', /dev/input/event9 is tagged by udev as: Keyboard

[     6.425] (II) input device 'Video Bus', /dev/input/event9 is a keyboard

[     6.425] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)

[     6.425] (II) No input driver specified, ignoring this device.

[     6.425] (II) This device may have been added with another device file.

[     6.426] (II) config/udev: Adding input device Sleep Button (/dev/input/event3)

[     6.426] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"

[     6.426] (II) Using input driver 'libinput' for 'Sleep Button'

[     6.426] (**) Sleep Button: always reports core events

[     6.426] (**) Option "Device" "/dev/input/event3"

[     6.426] (**) Option "_source" "server/udev"

[     6.426] (II) input device 'Sleep Button', /dev/input/event3 is tagged by udev as: Keyboard

[     6.426] (II) input device 'Sleep Button', /dev/input/event3 is a keyboard

[     6.440] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3/event3"

[     6.440] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 10)

[     6.440] (**) Option "xkb_model" "pc105"

[     6.440] (**) Option "xkb_layout" "fr"

[     6.440] (**) Option "xkb_variant" "latin9"

[     6.441] (II) input device 'Sleep Button', /dev/input/event3 is tagged by udev as: Keyboard

[     6.441] (II) input device 'Sleep Button', /dev/input/event3 is a keyboard

[     6.442] (II) config/udev: Adding input device USB2.0 HD UVC WebCam (/dev/input/event6)

[     6.442] (**) USB2.0 HD UVC WebCam: Applying InputClass "libinput keyboard catchall"

[     6.442] (II) Using input driver 'libinput' for 'USB2.0 HD UVC WebCam'

[     6.442] (**) USB2.0 HD UVC WebCam: always reports core events

[     6.442] (**) Option "Device" "/dev/input/event6"

[     6.442] (**) Option "_source" "server/udev"

[     6.443] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is tagged by udev as: Keyboard

[     6.443] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is a keyboard

[     6.472] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/input/input6/event6"

[     6.472] (II) XINPUT: Adding extended input device "USB2.0 HD UVC WebCam" (type: KEYBOARD, id 11)

[     6.472] (**) Option "xkb_model" "pc105"

[     6.472] (**) Option "xkb_layout" "fr"

[     6.472] (**) Option "xkb_variant" "latin9"

[     6.473] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is tagged by udev as: Keyboard

[     6.473] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is a keyboard

[     6.474] (II) config/udev: Adding input device Elan Touchpad (/dev/input/event14)

[     6.474] (**) Elan Touchpad: Applying InputClass "libinput touchpad catchall"

[     6.474] (II) Using input driver 'libinput' for 'Elan Touchpad'

[     6.474] (**) Elan Touchpad: always reports core events

[     6.474] (**) Option "Device" "/dev/input/event14"

[     6.474] (**) Option "_source" "server/udev"

[     6.474] (II) input device 'Elan Touchpad', /dev/input/event14 is tagged by udev as: Touchpad

[     6.474] (II) input device 'Elan Touchpad', /dev/input/event14 is a touchpad

[     6.504] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-20/i2c-ELAN1000:00/input/input14/event14"

[     6.504] (II) XINPUT: Adding extended input device "Elan Touchpad" (type: TOUCHPAD, id 12)

[     6.504] (**) Option "AccelerationScheme" "none"

[     6.504] (**) Elan Touchpad: (accel) selected scheme none/0

[     6.504] (**) Elan Touchpad: (accel) acceleration factor: 2.000

[     6.504] (**) Elan Touchpad: (accel) acceleration threshold: 4

[     6.505] (II) input device 'Elan Touchpad', /dev/input/event14 is tagged by udev as: Touchpad

[     6.505] (II) input device 'Elan Touchpad', /dev/input/event14 is a touchpad

[     6.506] (II) config/udev: Adding input device Elan Touchpad (/dev/input/mouse0)

[     6.506] (II) No input driver specified, ignoring this device.

[     6.506] (II) This device may have been added with another device file.

[     6.506] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event10)

[     6.506] (II) No input driver specified, ignoring this device.

[     6.506] (II) This device may have been added with another device file.

[     6.507] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event11)

[     6.507] (II) No input driver specified, ignoring this device.

[     6.507] (II) This device may have been added with another device file.

[     6.507] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event12)

[     6.507] (II) No input driver specified, ignoring this device.

[     6.507] (II) This device may have been added with another device file.

[     6.508] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event13)

[     6.508] (II) No input driver specified, ignoring this device.

[     6.508] (II) This device may have been added with another device file.

[     6.508] (II) config/udev: Adding input device Asus WMI hotkeys (/dev/input/event7)

[     6.508] (**) Asus WMI hotkeys: Applying InputClass "libinput keyboard catchall"

[     6.508] (II) Using input driver 'libinput' for 'Asus WMI hotkeys'

[     6.508] (**) Asus WMI hotkeys: always reports core events

[     6.508] (**) Option "Device" "/dev/input/event7"

[     6.508] (**) Option "_source" "server/udev"

[     6.509] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is tagged by udev as: Keyboard

[     6.509] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is a keyboard

[     6.532] (**) Option "config_info" "udev:/sys/devices/platform/asus-nb-wmi/input/input7/event7"

[     6.532] (II) XINPUT: Adding extended input device "Asus WMI hotkeys" (type: KEYBOARD, id 13)

[     6.532] (**) Option "xkb_model" "pc105"

[     6.532] (**) Option "xkb_layout" "fr"

[     6.532] (**) Option "xkb_variant" "latin9"

[     6.533] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is tagged by udev as: Keyboard

[     6.533] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is a keyboard

[     6.533] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)

[     6.533] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"

[     6.533] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'

[     6.533] (**) AT Translated Set 2 keyboard: always reports core events

[     6.533] (**) Option "Device" "/dev/input/event0"

[     6.533] (**) Option "_source" "server/udev"

[     6.534] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard

[     6.534] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard

[     6.564] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"

[     6.564] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 14)

[     6.564] (**) Option "xkb_model" "pc105"

[     6.564] (**) Option "xkb_layout" "fr"

[     6.564] (**) Option "xkb_variant" "latin9"

[     6.565] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard

[     6.565] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard

[     6.565] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)

[     6.565] (II) No input driver specified, ignoring this device.

[     6.565] (II) This device may have been added with another device file.

[    19.957] (II) modeset(0): EDID vendor "AUO", prod id 14573

[    19.957] (II) modeset(0): Printing DDC gathered Modelines:

[    19.957] (II) modeset(0): Modeline "1920x1080"x0.0  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[    20.205] (II) modeset(0): EDID vendor "AUO", prod id 14573

[    20.206] (II) modeset(0): Printing DDC gathered Modelines:

[    20.206] (II) modeset(0): Modeline "1920x1080"x0.0  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[    20.459] (II) modeset(0): EDID vendor "AUO", prod id 14573

[    20.459] (II) modeset(0): Printing DDC gathered Modelines:

[    20.459] (II) modeset(0): Modeline "1920x1080"x0.0  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[    20.705] (II) modeset(0): EDID vendor "AUO", prod id 14573

[    20.705] (II) modeset(0): Printing DDC gathered Modelines:

[    20.705] (II) modeset(0): Modeline "1920x1080"x0.0  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

J'ai reinstaller le paquet firmware-misc-nonfree ça m'a téléchargé quelques trucs mais lorsque je me logg sur le bureau sous gnome avec le lanceur lightdm ça m'affiche le fond d'écran uniquement avec la souris que je peux déplacer, rien d'autre.

Si je lance avec le lanceur gdm3, une fois que j'entre mon username et mon password et que j'appuis sur connecter l'écran devient noire et s'éteint et je retourne au problème initial

EDIT: Je peux tout de même utiliser la console via ctrl+alt+F1

Dernière modification par Manahoar (05-04-2017 02:15:16)

anonyme · 05-04-2017 02:19:02

tu a essayé de choisir gnome-classic comme bureau ? voir si c'est mieux ?

pour le log c'est toujours correct

Dernière modification par anonyme (05-04-2017 02:19:47)

Manahoar · 05-04-2017 02:21:51

Alors cette fois-ci, si je choisis gnome-classic j'ai le fond d'écran gris qui s'affiche mais tout est figé, souris et clavier.

anonyme · 05-04-2017 02:23:52

en plus => "[ 5.218] (II) modesetting: Driver for Modesetting Kernel Drivers: kms"

et nouveau se charge plus puisque il n'est plus installé =>

[     5.216] (II) LoadModule: "nouveau"

[     5.216] (WW) Warning, couldn't open module nouveau

[     5.216] (II) UnloadModule: "nouveau"

[     5.216] (II) Unloading nouveau

[     5.215] (==) Matched modesetting as autoconfigured driver 2

 

KMS initialise bien les 2 gpu je comprend pas (l init dri2 et glx correct pour les deux log ) , normalement gnome doit démarrer sur la carte intel qui est correcte

avec gdm3 tu peu entrer sur mate ?

Dernière modification par anonyme (05-04-2017 02:34:08)

Manahoar · 05-04-2017 02:31:44

Information qui peut être utile, au moment du boot arrivé à grub j'appuis sur e et j'ajoute à la ligne qui débute par linux et qui termine par quiet tout à la fin je rajoute:

nouveau.modeset=0

Avec le bureau gnome-classic et gnome une fois loggé tout fonctionne parfaitement.

EDIT: Oui avec gdm3 je peu entrer sur mate lorsque j'ai la commande "nouveau.modeset=0" activé dans grub, dans le cas contraire une fois log le PC se fige avec le fond d'écran et la souris qui est impossible à déplacer.

Dernière modification par Manahoar (05-04-2017 02:40:19)

Manahoar · 05-04-2017 02:40:34

EDIT:erreur double poste, msg à supprimer

Dernière modification par Manahoar (05-04-2017 02:41:01)

anonyme · 05-04-2017 02:41:29

donc un bug avec nouveau , mais ton bureau a bien la définition native de l'écran ? ça te semble correct ?
mais avec le driver nvidia normalement le driver nouveau est désactivé (du serveur X et de KMS )
avec les portables toujours des embrouilles

a voir avec bumblebee ce que ça va donner
pour grub tu peu la rentrer en dur cette commande et meme je pense quelle fonctionne aussi dans /etc/modprobe.d/tonfichier.conf avec le contenu "nouveau.modeset=0"

tu devrais faire des tests de mesa

avec le paquet "mesa-utils"

Ce paquet fournit divers utilitaires simples GL construits pour Mesa, comme

glxinfo et glxgears.

sous stretch

glxinfo -B

 

name of display: :0

display: :0  screen: 0

direct rendering: Yes

OpenGL vendor string: NVIDIA Corporation

OpenGL renderer string: GeForce GTX 750 Ti/PCIe/SSE2

OpenGL core profile version string: 4.5.0 NVIDIA 375.39

OpenGL core profile shading language version string: 4.50 NVIDIA

OpenGL core profile context flags: (none)

OpenGL core profile profile mask: core profile

OpenGL version string: 4.5.0 NVIDIA 375.39

OpenGL shading language version string: 4.50 NVIDIA

OpenGL context flags: (none)

OpenGL profile mask: (none)

OpenGL ES profile version string: OpenGL ES 3.2 NVIDIA 375.39

OpenGL ES profile shading language version string: OpenGL ES GLSL ES 3.20

glxgears

 

Running synchronized to the vertical refresh.  The framerate should be

approximately the same as the monitor refresh rate.

302 frames in 5.0 seconds = 60.306 FPS

300 frames in 5.0 seconds = 59.894 FPS

300 frames in 5.0 seconds = 59.830 FPS

XIO:  fatal IO error 11 (Resource temporarily unavailable) on X server ":0"

      after 49 requests (49 known processed) with 0 events remaining.

pour tester ton gpu intel (moi ici en exemple une nvidia )

je sais comment Asus a configuré ses 2 gpu mais le duo gdm3 + gnome bloque sur le module "nouveau" (en espérant que pour bumblebee ça ne pose pas problème )
actuellement tu a désactivé nouveau (du noyau et du serveur X) peut etre une recherche sur ton type de portable sur le net voir si le problème est connu
en tout cas nouveau-modeset=0 ne dérange en rien le bon fonctionnement , meme avec bumblebee-nvidia

Dernière modification par anonyme (05-04-2017 03:02:02)

Manahoar · 05-04-2017 02:59:33

Niveau résolution je suis impeccable. En 1920*1080 y'a aucun problème d'affichage.

Voici mes résultats des commandes que tu me de demande de taper

glxinfo -B

name of display: :0

display: :0  screen: 0

direct rendering: Yes

Extended renderer info (GLX_MESA_query_renderer):

    Vendor: Intel Open Source Technology Center (0x8086)

    Device: Mesa DRI Intel(R) HD Graphics 530 (Skylake GT2)  (0x191b)

    Version: 13.0.6

    Accelerated: yes

    Video memory: 3072MB

    Unified memory: yes

    Preferred profile: core (0x1)

    Max core profile version: 4.5

    Max compat profile version: 3.0

    Max GLES1 profile version: 1.1

    Max GLES[23] profile version: 3.2

OpenGL vendor string: Intel Open Source Technology Center

OpenGL renderer string: Mesa DRI Intel(R) HD Graphics 530 (Skylake GT2) 

OpenGL core profile version string: 4.5 (Core Profile) Mesa 13.0.6

OpenGL core profile shading language version string: 4.50

OpenGL core profile context flags: (none)

OpenGL core profile profile mask: core profile

OpenGL version string: 3.0 Mesa 13.0.6

OpenGL shading language version string: 1.30

OpenGL context flags: (none)

OpenGL ES profile version string: OpenGL ES 3.2 Mesa 13.0.6

OpenGL ES profile shading language version string: OpenGL ES GLSL ES 3.20

Pour l'autre commande:

glxgears

Running synchronized to the vertical refresh.  The framerate should be

approximately the same as the monitor refresh rate.

334 frames in 5.0 seconds = 66.648 FPS

301 frames in 5.0 seconds = 60.053 FPS

301 frames in 5.0 seconds = 60.050 FPS

301 frames in 5.0 seconds = 60.051 FPS

301 frames in 5.0 seconds = 60.050 FPS

301 frames in 5.0 seconds = 60.051 FPS

301 frames in 5.0 seconds = 60.050 FPS

301 frames in 5.0 seconds = 60.050 FPS

301 frames in 5.0 seconds = 60.050 FPS

XIO:  fatal IO error 11 (Resource temporarily unavailable) on X server ":0"

      after 3031 requests (3031 known processed) with 0 events remaining.

anonyme · 05-04-2017 03:05:16

c'est parfait pour intel , soit tu attends demain pour bumblebee-nvidia le retour des membres qui ont un portable (pas la peine de tester bumblebee avec nouveau

)
soit tu teste maintenant , tu utilise le wiki de debian facile ?

Manahoar · 05-04-2017 03:07:45

Alors oui je utilise le wiki de debian facile et je suis scrupuleusement tous ce qu'il y a d'écrit.

Je vais aller me coucher merci beaucoup pour m'avoir aidé dans une heure si tardive !

Je continuerais demain dans la journée bonne nuit.

anonyme · 05-04-2017 03:08:34

=> https://debian-facile.org/doc:materiel: … ia:optimus

ok bonne nuit
@++

Manahoar · 05-04-2017 13:19:12

Ok donc voici du nouveau ! J'ai suivi la doc debian-facile pour re-installer Bumblebee( https://debian-facile.org/doc:materiel: … ia:optimus ) avec les drivers nvidia prioritaire vu que nouveau ne fonctionnait visiblement pas et après ça ne fonctionne toujours pas. gdm3 fonctionne parfaitement et lorsque j'essaye de me logger sous Mate ou Gnome j'ai l'écran qui se fige sur le fond d'écran avec la souris qui est impossible à bouger.

Voici ce que j'ai fais:

apt-get install nvidia-kernel-dkms nvidia-xconfig nvidia-settings nvidia-vdpau-driver vdpau-va-driver mesa-utils bumblebee-nvidia primus xserver-xorg-video-nvidia linux-headers-$(uname -r)

J'ai bien fais attention à ce qu'il n'y ai pas de fichier xorg.conf

J'ai vérifié si les pilotes nouveau étaient bien désactivé, c'était le cas:

lsmod | egrep -i "nouveau|vga_switcheroo" 

Aucune réponse, ça signifiait que tout a bien été fait

J'ai téléchargé et installé virtualgl_2.5.2_amd64.deb

dpkg -i virtualgl_2.5.2_amd64.deb

Ajouté les utilisateurs au groupe bumblebee, installation terminé on me demande dans le wiki de reboot le portable.

Après reboot, gdm3 fonctionne mais tout se fige lorsque je me log sous Mate ou Gnome et le pc ne répond plus.

_________________________________LOGS________________________________________________

Je ne sais pas si ça peut aider, mais voici le contenu de "cat /var/log/Xorg.0.log" après le démarrage.

[     5.123] 

X.Org X Server 1.19.2

Release Date: 2017-03-02

[     5.123] X Protocol Version 11, Revision 0

[     5.123] Build Operating System: Linux 3.16.0-4-amd64 x86_64 Debian

[     5.123] Current Operating System: Linux debian-mnhr 4.9.0-2-amd64 #1 SMP Debian 4.9.13-1 (2017-02-27) x86_64

[     5.123] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-2-amd64 root=UUID=d11a650c-29a7-47bc-99af-e1b4de5522ea ro quiet

[     5.123] Build Date: 03 March 2017  03:14:41PM

[     5.123] xorg-server 2:1.19.2-1 (https://www.debian.org/support) 

[     5.123] Current version of pixman: 0.34.0

[     5.123]  Before reporting problems, check http://wiki.x.org

  to make sure that you have the latest version.

[     5.123] Markers: (--) probed, (**) from config file, (==) default setting,

  (++) from command line, (!!) notice, (II) informational,

  (WW) warning, (EE) error, (NI) not implemented, (??) unknown.

[     5.123] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Apr  5 03:04:44 2017

[     5.125] (==) Using system config directory "/usr/share/X11/xorg.conf.d"

[     5.126] (==) No Layout section.  Using the first Screen section.

[     5.126] (==) No screen section available. Using defaults.

[     5.126] (**) |-->Screen "Default Screen Section" (0)

[     5.126] (**) |   |-->Monitor "<default monitor>"

[     5.127] (==) No monitor specified for screen "Default Screen Section".

  Using a default monitor configuration.

[     5.127] (==) Automatically adding devices

[     5.127] (==) Automatically enabling devices

[     5.127] (==) Automatically adding GPU devices

[     5.127] (==) Max clients allowed: 256, resource mask: 0x1fffff

[     5.128] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.

[     5.128]  Entry deleted from font path.

[     5.128] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.

[     5.128]  Entry deleted from font path.

[     5.128] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.

[     5.128]  Entry deleted from font path.

[     5.128] (WW) The directory "/usr/share/fonts/X11/Type1" does not exist.

[     5.128]  Entry deleted from font path.

[     5.128] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.

[     5.128]  Entry deleted from font path.

[     5.128] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.

[     5.128]  Entry deleted from font path.

[     5.128] (==) FontPath set to:

  /usr/share/fonts/X11/misc,

  built-ins

[     5.128] (==) ModulePath set to "/usr/lib/xorg/modules"

[     5.128] (II) The server relies on udev to provide the list of input devices.

  If no devices become available, reconfigure udev or disable AutoAddDevices.

[     5.128] (II) Loader magic: 0x557f204cde00

[     5.128] (II) Module ABI versions:

[     5.128]  X.Org ANSI C Emulation: 0.4

[     5.128]  X.Org Video Driver: 23.0

[     5.128]  X.Org XInput driver : 24.1

[     5.128]  X.Org Server Extension : 10.0

[     5.129] (++) using VT number 7

[     5.129] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration

[     5.129] (II) xfree86: Adding drm device (/dev/dri/card1)

[     5.129] (II) xfree86: Adding drm device (/dev/dri/card0)

[     5.133] (--) PCI:*(0:0:2:0) 8086:191b:1043:1c5d rev 6, Mem @ 0xdd000000/16777216, 0xb0000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072

[     5.133] (--) PCI: (0:1:0:0) 10de:139b:1043:1c5d rev 162, Mem @ 0xde000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288

[     5.133] (II) LoadModule: "glx"

[     5.135] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so

[     5.148] (II) Module glx: vendor="X.Org Foundation"

[     5.148]  compiled for 1.19.2, module version = 1.0.0

[     5.148]  ABI class: X.Org Server Extension, version 10.0

[     5.149] (==) Matched nouveau as autoconfigured driver 0

[     5.149] (==) Matched nv as autoconfigured driver 1

[     5.149] (==) Matched modesetting as autoconfigured driver 2

[     5.149] (==) Matched fbdev as autoconfigured driver 3

[     5.149] (==) Matched vesa as autoconfigured driver 4

[     5.149] (==) Assigned the driver to the xf86ConfigLayout

[     5.149] (II) LoadModule: "nouveau"

[     5.149] (WW) Warning, couldn't open module nouveau

[     5.149] (II) UnloadModule: "nouveau"

[     5.149] (II) Unloading nouveau

[     5.149] (EE) Failed to load module "nouveau" (module does not exist, 0)

[     5.149] (II) LoadModule: "nv"

[     5.149] (WW) Warning, couldn't open module nv

[     5.149] (II) UnloadModule: "nv"

[     5.149] (II) Unloading nv

[     5.149] (EE) Failed to load module "nv" (module does not exist, 0)

[     5.149] (II) LoadModule: "modesetting"

[     5.149] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so

[     5.151] (II) Module modesetting: vendor="X.Org Foundation"

[     5.151]  compiled for 1.19.2, module version = 1.19.2

[     5.151]  Module class: X.Org Video Driver

[     5.151]  ABI class: X.Org Video Driver, version 23.0

[     5.151] (II) LoadModule: "fbdev"

[     5.151] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so

[     5.152] (II) Module fbdev: vendor="X.Org Foundation"

[     5.152]  compiled for 1.19.0, module version = 0.4.4

[     5.152]  Module class: X.Org Video Driver

[     5.152]  ABI class: X.Org Video Driver, version 23.0

[     5.152] (II) LoadModule: "vesa"

[     5.152] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so

[     5.153] (II) Module vesa: vendor="X.Org Foundation"

[     5.153]  compiled for 1.19.0, module version = 2.3.4

[     5.153]  Module class: X.Org Video Driver

[     5.153]  ABI class: X.Org Video Driver, version 23.0

[     5.153] (II) modesetting: Driver for Modesetting Kernel Drivers: kms

[     5.153] (II) FBDEV: driver for framebuffer: fbdev

[     5.153] (II) VESA: driver for VESA chipsets: vesa

[     5.181] (II) modeset(0): using drv /dev/dri/card0

[     5.181] (II) modeset(G0): using drv /dev/dri/card1

[     5.181] (WW) Falling back to old probe method for fbdev

[     5.181] (II) Loading sub module "fbdevhw"

[     5.181] (II) LoadModule: "fbdevhw"

[     5.181] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so

[     5.182] (II) Module fbdevhw: vendor="X.Org Foundation"

[     5.182]  compiled for 1.19.2, module version = 0.0.2

[     5.182]  ABI class: X.Org Video Driver, version 23.0

[     5.182] (WW) Falling back to old probe method for vesa

[     5.182] (II) modeset(0): Creating default Display subsection in Screen section

  "Default Screen Section" for depth/fbbpp 24/32

[     5.182] (==) modeset(0): Depth 24, (==) framebuffer bpp 32

[     5.182] (==) modeset(0): RGB weight 888

[     5.182] (==) modeset(0): Default visual is TrueColor

[     5.182] (II) Loading sub module "glamoregl"

[     5.182] (II) LoadModule: "glamoregl"

[     5.182] (II) Loading /usr/lib/xorg/modules/libglamoregl.so

[     5.197] (II) Module glamoregl: vendor="X.Org Foundation"

[     5.197]  compiled for 1.19.2, module version = 1.0.0

[     5.197]  ABI class: X.Org ANSI C Emulation, version 0.4

[     5.197] (II) glamor: OpenGL accelerated X.org driver based.

[     5.238] (II) glamor: EGL version 1.4 (DRI2):

[     5.250] (II) modeset(0): glamor initialized

[     5.250] (II) modeset(0): Output eDP-1 has no monitor section

[     5.252] (II) modeset(0): Output DP-1 has no monitor section

[     5.379] (II) modeset(0): Output HDMI-1 has no monitor section

[     5.381] (II) modeset(0): Output HDMI-2 has no monitor section

[     5.383] (II) modeset(0): Output DP-2 has no monitor section

[     5.507] (II) modeset(0): Output HDMI-3 has no monitor section

[     5.508] (II) modeset(0): EDID for output eDP-1

[     5.508] (II) modeset(0): Manufacturer: AUO  Model: 38ed  Serial#: 0

[     5.508] (II) modeset(0): Year: 2014  Week: 43

[     5.508] (II) modeset(0): EDID Version: 1.4

[     5.508] (II) modeset(0): Digital Display Input

[     5.508] (II) modeset(0): 6 bits per channel

[     5.508] (II) modeset(0): Digital interface is DisplayPort

[     5.508] (II) modeset(0): Max Image Size [cm]: horiz.: 34  vert.: 19

[     5.508] (II) modeset(0): Gamma: 2.20

[     5.508] (II) modeset(0): No DPMS capabilities specified

[     5.508] (II) modeset(0): Supported color encodings: RGB 4:4:4 

[     5.508] (II) modeset(0): First detailed timing is preferred mode

[     5.508] (II) modeset(0): Preferred mode is native pixel format and refresh rate

[     5.508] (II) modeset(0): redX: 0.575 redY: 0.345   greenX: 0.340 greenY: 0.560

[     5.508] (II) modeset(0): blueX: 0.156 blueY: 0.123   whiteX: 0.313 whiteY: 0.329

[     5.508] (II) modeset(0): Manufacturer's mask: 0

[     5.508] (II) modeset(0): Supported detailed timing:

[     5.508] (II) modeset(0): clock: 142.0 MHz   Image Size:  344 x 193 mm

[     5.508] (II) modeset(0): h_active: 1920  h_sync: 2028  h_sync_end 2076 h_blank_end 2100 h_border: 0

[     5.508] (II) modeset(0): v_active: 1080  v_sync: 1090  v_sync_end 1100 v_blanking: 1126 v_border: 0

[     5.508] (II) modeset(0): Unknown vendor-specific block f

[     5.508] (II) modeset(0):  AUO

[     5.508] (II) modeset(0):  B156HTN03.8

[     5.508] (II) modeset(0): EDID (in hex):

[     5.508] (II) modeset(0):   00ffffffffffff0006afed3800000000

[     5.508] (II) modeset(0):   2b180104952213780251259358578f28

[     5.508] (II) modeset(0):   1f505400000001010101010101010101

[     5.508] (II) modeset(0):   010101010101783780b470382e406c30

[     5.508] (II) modeset(0):   aa0058c1100000180000000f00000000

[     5.508] (II) modeset(0):   00000000000000000020000000fe0041

[     5.508] (II) modeset(0):   554f0a202020202020202020000000fe

[     5.508] (II) modeset(0):   004231353648544e30332e38200a00e9

[     5.508] (II) modeset(0): Printing probed modes for output eDP-1

[     5.508] (II) modeset(0): Modeline "1920x1080"x60.1  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[     5.508] (II) modeset(0): Modeline "1920x1080"x59.9  138.50  1920 1968 2000 2080  1080 1083 1088 1111 +hsync -vsync (66.6 kHz d)

[     5.508] (II) modeset(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz d)

[     5.508] (II) modeset(0): Modeline "1680x1050"x59.9  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz d)

[     5.508] (II) modeset(0): Modeline "1600x1024"x60.2  103.12  1600 1600 1656 1664  1024 1024 1029 1030 +hsync +vsync (62.0 kHz d)

[     5.508] (II) modeset(0): Modeline "1400x1050"x60.0  122.00  1400 1488 1640 1880  1050 1052 1064 1082 +hsync +vsync (64.9 kHz d)

[     5.508] (II) modeset(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz d)

[     5.508] (II) modeset(0): Modeline "1440x900"x59.9  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz d)

[     5.508] (II) modeset(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz d)

[     5.508] (II) modeset(0): Modeline "1360x768"x59.8   84.75  1360 1432 1568 1776  768 771 781 798 -hsync +vsync (47.7 kHz d)

[     5.508] (II) modeset(0): Modeline "1360x768"x60.0   72.00  1360 1408 1440 1520  768 771 781 790 +hsync -vsync (47.4 kHz d)

[     5.508] (II) modeset(0): Modeline "1152x864"x60.0   81.62  1152 1216 1336 1520  864 865 868 895 -hsync +vsync (53.7 kHz d)

[     5.509] (II) modeset(0): Modeline "1024x768"x120.1  133.47  1024 1100 1212 1400  768 768 770 794 doublescan -hsync +vsync (95.3 kHz d)

[     5.509] (II) modeset(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz d)

[     5.509] (II) modeset(0): Modeline "960x720"x120.0  117.00  960 1024 1128 1300  720 720 722 750 doublescan -hsync +vsync (90.0 kHz d)

[     5.509] (II) modeset(0): Modeline "928x696"x120.1  109.15  928 976 1088 1264  696 696 698 719 doublescan -hsync +vsync (86.4 kHz d)

[     5.509] (II) modeset(0): Modeline "896x672"x120.0  102.40  896 960 1060 1224  672 672 674 697 doublescan -hsync +vsync (83.7 kHz d)

[     5.509] (II) modeset(0): Modeline "960x600"x120.0   77.00  960 984 1000 1040  600 601 604 617 doublescan +hsync -vsync (74.0 kHz d)

[     5.509] (II) modeset(0): Modeline "960x540"x120.0   69.25  960 984 1000 1040  540 541 544 555 doublescan +hsync -vsync (66.6 kHz d)

[     5.509] (II) modeset(0): Modeline "800x600"x120.0   81.00  800 832 928 1080  600 600 602 625 doublescan +hsync +vsync (75.0 kHz d)

[     5.509] (II) modeset(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz d)

[     5.509] (II) modeset(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz d)

[     5.509] (II) modeset(0): Modeline "840x525"x120.0   73.12  840 892 980 1120  525 526 529 544 doublescan -hsync +vsync (65.3 kHz d)

[     5.509] (II) modeset(0): Modeline "840x525"x119.8   59.50  840 864 880 920  525 526 529 540 doublescan +hsync -vsync (64.7 kHz d)

[     5.509] (II) modeset(0): Modeline "800x512"x120.3   51.56  800 800 828 832  512 512 514 515 doublescan +hsync +vsync (62.0 kHz d)

[     5.509] (II) modeset(0): Modeline "700x525"x120.0   61.00  700 744 820 940  525 526 532 541 doublescan +hsync +vsync (64.9 kHz d)

[     5.509] (II) modeset(0): Modeline "640x512"x120.0   54.00  640 664 720 844  512 512 514 533 doublescan +hsync +vsync (64.0 kHz d)

[     5.509] (II) modeset(0): Modeline "720x450"x119.8   53.25  720 760 836 952  450 451 454 467 doublescan -hsync +vsync (55.9 kHz d)

[     5.509] (II) modeset(0): Modeline "640x480"x120.0   54.00  640 688 744 900  480 480 482 500 doublescan +hsync +vsync (60.0 kHz d)

[     5.509] (II) modeset(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz d)

[     5.509] (II) modeset(0): Modeline "680x384"x119.6   42.38  680 716 784 888  384 385 390 399 doublescan -hsync +vsync (47.7 kHz d)

[     5.509] (II) modeset(0): Modeline "680x384"x119.9   36.00  680 704 720 760  384 385 390 395 doublescan +hsync -vsync (47.4 kHz d)

[     5.509] (II) modeset(0): Modeline "576x432"x120.1   40.81  576 608 668 760  432 432 434 447 doublescan -hsync +vsync (53.7 kHz d)

[     5.509] (II) modeset(0): Modeline "512x384"x120.0   32.50  512 524 592 672  384 385 388 403 doublescan -hsync -vsync (48.4 kHz d)

[     5.509] (II) modeset(0): Modeline "400x300"x120.6   20.00  400 420 484 528  300 300 302 314 doublescan +hsync +vsync (37.9 kHz d)

[     5.509] (II) modeset(0): Modeline "400x300"x112.7   18.00  400 412 448 512  300 300 301 312 doublescan +hsync +vsync (35.2 kHz d)

[     5.509] (II) modeset(0): Modeline "320x240"x120.1   12.59  320 328 376 400  240 245 246 262 doublescan -hsync -vsync (31.5 kHz d)

[     5.511] (II) modeset(0): EDID for output DP-1

[     5.632] (II) modeset(0): EDID for output HDMI-1

[     5.634] (II) modeset(0): EDID for output HDMI-2

[     5.636] (II) modeset(0): EDID for output DP-2

[     5.760] (II) modeset(0): EDID for output HDMI-3

[     5.760] (II) modeset(0): Output eDP-1 connected

[     5.760] (II) modeset(0): Output DP-1 disconnected

[     5.760] (II) modeset(0): Output HDMI-1 disconnected

[     5.760] (II) modeset(0): Output HDMI-2 disconnected

[     5.760] (II) modeset(0): Output DP-2 disconnected

[     5.760] (II) modeset(0): Output HDMI-3 disconnected

[     5.760] (II) modeset(0): Using exact sizes for initial modes

[     5.760] (II) modeset(0): Output eDP-1 using initial mode 1920x1080 +0+0

[     5.760] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)

[     5.760] (==) modeset(0): DPI set to (96, 96)

[     5.760] (II) Loading sub module "fb"

[     5.760] (II) LoadModule: "fb"

[     5.760] (II) Loading /usr/lib/xorg/modules/libfb.so

[     5.762] (II) Module fb: vendor="X.Org Foundation"

[     5.762]  compiled for 1.19.2, module version = 1.0.0

[     5.762]  ABI class: X.Org ANSI C Emulation, version 0.4

[     5.785] (==) modeset(G0): Depth 24, (==) framebuffer bpp 32

[     5.785] (==) modeset(G0): RGB weight 888

[     5.785] (==) modeset(G0): Default visual is TrueColor

[     5.785] (II) Loading sub module "glamoregl"

[     5.785] (II) LoadModule: "glamoregl"

[     5.785] (II) Loading /usr/lib/xorg/modules/libglamoregl.so

[     5.785] (II) Module glamoregl: vendor="X.Org Foundation"

[     5.785]  compiled for 1.19.2, module version = 1.0.0

[     5.785]  ABI class: X.Org ANSI C Emulation, version 0.4

[     5.785] (II) glamor: OpenGL accelerated X.org driver based.

[     6.087] (II) glamor: EGL version 1.4 (DRI2):

[     6.097] (II) modeset(G0): glamor initialized

[     6.097] (==) modeset(G0): Using gamma correction (1.0, 1.0, 1.0)

[     6.097] (==) modeset(G0): DPI set to (96, 96)

[     6.097] (II) Loading sub module "fb"

[     6.097] (II) LoadModule: "fb"

[     6.097] (II) Loading /usr/lib/xorg/modules/libfb.so

[     6.097] (II) Module fb: vendor="X.Org Foundation"

[     6.097]  compiled for 1.19.2, module version = 1.0.0

[     6.097]  ABI class: X.Org ANSI C Emulation, version 0.4

[     6.097] (II) UnloadModule: "fbdev"

[     6.097] (II) Unloading fbdev

[     6.097] (II) UnloadSubModule: "fbdevhw"

[     6.097] (II) Unloading fbdevhw

[     6.098] (II) UnloadModule: "vesa"

[     6.098] (II) Unloading vesa

[     6.098] (==) Depth 24 pixmap format is 32 bpp

[     6.145] (==) modeset(G0): Backing store enabled

[     6.145] (==) modeset(G0): Silken mouse enabled

[     6.145] (II) modeset(G0): RandR 1.2 enabled, ignore the following RandR disabled message.

[     6.146] (==) modeset(G0): DPMS enabled

[     6.146] (II) modeset(G0): [DRI2] Setup complete

[     6.146] (II) modeset(G0): [DRI2]   DRI driver: nouveau

[     6.146] (II) modeset(G0): [DRI2]   VDPAU driver: nouveau

[     6.221] (==) modeset(0): Backing store enabled

[     6.221] (==) modeset(0): Silken mouse enabled

[     6.221] (II) modeset(0): RandR 1.2 enabled, ignore the following RandR disabled message.

[     6.221] (==) modeset(0): DPMS enabled

[     6.221] (II) modeset(0): [DRI2] Setup complete

[     6.221] (II) modeset(0): [DRI2]   DRI driver: i965

[     6.221] (II) modeset(0): [DRI2]   VDPAU driver: i965

[     6.221] (--) RandR disabled

[     6.224] (II) SELinux: Disabled on system

[     6.228] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer

[     6.228] (II) AIGLX: enabled GLX_ARB_create_context

[     6.228] (II) AIGLX: enabled GLX_ARB_create_context_profile

[     6.228] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile

[     6.228] (II) AIGLX: enabled GLX_INTEL_swap_event

[     6.228] (II) AIGLX: enabled GLX_SGI_swap_control

[     6.228] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB

[     6.228] (II) AIGLX: enabled GLX_ARB_fbconfig_float

[     6.228] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float

[     6.228] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects

[     6.228] (II) AIGLX: enabled GLX_ARB_create_context_robustness

[     6.228] (II) AIGLX: Loaded and initialized i965

[     6.228] (II) GLX: Initialized DRI2 GL provider for screen 0

[     6.229] (II) modeset(G0): Damage tracking initialized

[     6.232] (II) modeset(0): Damage tracking initialized

[     6.232] (II) modeset(0): Setting screen physical size to 508 x 285

[     6.264] (II) config/udev: Adding input device Power Button (/dev/input/event3)

[     6.264] (**) Power Button: Applying InputClass "libinput keyboard catchall"

[     6.264] (II) LoadModule: "libinput"

[     6.264] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so

[     6.269] (II) Module libinput: vendor="X.Org Foundation"

[     6.269]  compiled for 1.19.0, module version = 0.23.0

[     6.269]  Module class: X.Org XInput Driver

[     6.269]  ABI class: X.Org XInput driver, version 24.1

[     6.269] (II) Using input driver 'libinput' for 'Power Button'

[     6.269] (**) Power Button: always reports core events

[     6.269] (**) Option "Device" "/dev/input/event3"

[     6.269] (**) Option "_source" "server/udev"

[     6.269] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard

[     6.269] (II) input device 'Power Button', /dev/input/event3 is a keyboard

[     6.304] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"

[     6.304] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)

[     6.304] (**) Option "xkb_model" "pc105"

[     6.304] (**) Option "xkb_layout" "fr"

[     6.304] (**) Option "xkb_variant" "latin9"

[     6.321] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard

[     6.321] (II) input device 'Power Button', /dev/input/event3 is a keyboard

[     6.322] (II) config/udev: Adding input device Asus Wireless Radio Control (/dev/input/event4)

[     6.322] (**) Asus Wireless Radio Control: Applying InputClass "libinput keyboard catchall"

[     6.322] (II) Using input driver 'libinput' for 'Asus Wireless Radio Control'

[     6.322] (**) Asus Wireless Radio Control: always reports core events

[     6.322] (**) Option "Device" "/dev/input/event4"

[     6.322] (**) Option "_source" "server/udev"

[     6.322] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is tagged by udev as: Keyboard

[     6.322] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is a keyboard

[     6.344] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/ATK4002:00/input/input4/event4"

[     6.344] (II) XINPUT: Adding extended input device "Asus Wireless Radio Control" (type: KEYBOARD, id 7)

[     6.344] (**) Option "xkb_model" "pc105"

[     6.344] (**) Option "xkb_layout" "fr"

[     6.344] (**) Option "xkb_variant" "latin9"

[     6.344] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is tagged by udev as: Keyboard

[     6.344] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is a keyboard

[     6.345] (II) config/udev: Adding input device Video Bus (/dev/input/event8)

[     6.345] (**) Video Bus: Applying InputClass "libinput keyboard catchall"

[     6.345] (II) Using input driver 'libinput' for 'Video Bus'

[     6.345] (**) Video Bus: always reports core events

[     6.345] (**) Option "Device" "/dev/input/event8"

[     6.345] (**) Option "_source" "server/udev"

[     6.345] (II) input device 'Video Bus', /dev/input/event8 is tagged by udev as: Keyboard

[     6.345] (II) input device 'Video Bus', /dev/input/event8 is a keyboard

[     6.360] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8/event8"

[     6.360] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)

[     6.360] (**) Option "xkb_model" "pc105"

[     6.360] (**) Option "xkb_layout" "fr"

[     6.360] (**) Option "xkb_variant" "latin9"

[     6.361] (II) input device 'Video Bus', /dev/input/event8 is tagged by udev as: Keyboard

[     6.361] (II) input device 'Video Bus', /dev/input/event8 is a keyboard

[     6.361] (II) config/udev: Adding input device Video Bus (/dev/input/event9)

[     6.361] (**) Video Bus: Applying InputClass "libinput keyboard catchall"

[     6.361] (II) Using input driver 'libinput' for 'Video Bus'

[     6.361] (**) Video Bus: always reports core events

[     6.361] (**) Option "Device" "/dev/input/event9"

[     6.361] (**) Option "_source" "server/udev"

[     6.362] (II) input device 'Video Bus', /dev/input/event9 is tagged by udev as: Keyboard

[     6.362] (II) input device 'Video Bus', /dev/input/event9 is a keyboard

[     6.376] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:12/LNXVIDEO:01/input/input9/event9"

[     6.376] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 9)

[     6.376] (**) Option "xkb_model" "pc105"

[     6.376] (**) Option "xkb_layout" "fr"

[     6.376] (**) Option "xkb_variant" "latin9"

[     6.377] (II) input device 'Video Bus', /dev/input/event9 is tagged by udev as: Keyboard

[     6.377] (II) input device 'Video Bus', /dev/input/event9 is a keyboard

[     6.377] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)

[     6.377] (II) No input driver specified, ignoring this device.

[     6.377] (II) This device may have been added with another device file.

[     6.378] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)

[     6.378] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"

[     6.378] (II) Using input driver 'libinput' for 'Sleep Button'

[     6.378] (**) Sleep Button: always reports core events

[     6.378] (**) Option "Device" "/dev/input/event2"

[     6.378] (**) Option "_source" "server/udev"

[     6.378] (II) input device 'Sleep Button', /dev/input/event2 is tagged by udev as: Keyboard

[     6.378] (II) input device 'Sleep Button', /dev/input/event2 is a keyboard

[     6.392] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2/event2"

[     6.392] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 10)

[     6.392] (**) Option "xkb_model" "pc105"

[     6.392] (**) Option "xkb_layout" "fr"

[     6.392] (**) Option "xkb_variant" "latin9"

[     6.393] (II) input device 'Sleep Button', /dev/input/event2 is tagged by udev as: Keyboard

[     6.393] (II) input device 'Sleep Button', /dev/input/event2 is a keyboard

[     6.394] (II) config/udev: Adding input device USB2.0 HD UVC WebCam (/dev/input/event6)

[     6.394] (**) USB2.0 HD UVC WebCam: Applying InputClass "libinput keyboard catchall"

[     6.394] (II) Using input driver 'libinput' for 'USB2.0 HD UVC WebCam'

[     6.394] (**) USB2.0 HD UVC WebCam: always reports core events

[     6.394] (**) Option "Device" "/dev/input/event6"

[     6.394] (**) Option "_source" "server/udev"

[     6.395] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is tagged by udev as: Keyboard

[     6.395] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is a keyboard

[     6.424] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/input/input6/event6"

[     6.424] (II) XINPUT: Adding extended input device "USB2.0 HD UVC WebCam" (type: KEYBOARD, id 11)

[     6.424] (**) Option "xkb_model" "pc105"

[     6.424] (**) Option "xkb_layout" "fr"

[     6.424] (**) Option "xkb_variant" "latin9"

[     6.425] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is tagged by udev as: Keyboard

[     6.425] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is a keyboard

[     6.426] (II) config/udev: Adding input device Elan Touchpad (/dev/input/event16)

[     6.426] (**) Elan Touchpad: Applying InputClass "libinput touchpad catchall"

[     6.426] (II) Using input driver 'libinput' for 'Elan Touchpad'

[     6.426] (**) Elan Touchpad: always reports core events

[     6.426] (**) Option "Device" "/dev/input/event16"

[     6.426] (**) Option "_source" "server/udev"

[     6.426] (II) input device 'Elan Touchpad', /dev/input/event16 is tagged by udev as: Touchpad

[     6.427] (II) input device 'Elan Touchpad', /dev/input/event16 is a touchpad

[     6.456] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-20/i2c-ELAN1000:00/input/input16/event16"

[     6.456] (II) XINPUT: Adding extended input device "Elan Touchpad" (type: TOUCHPAD, id 12)

[     6.456] (**) Option "AccelerationScheme" "none"

[     6.456] (**) Elan Touchpad: (accel) selected scheme none/0

[     6.456] (**) Elan Touchpad: (accel) acceleration factor: 2.000

[     6.456] (**) Elan Touchpad: (accel) acceleration threshold: 4

[     6.457] (II) input device 'Elan Touchpad', /dev/input/event16 is tagged by udev as: Touchpad

[     6.457] (II) input device 'Elan Touchpad', /dev/input/event16 is a touchpad

[     6.458] (II) config/udev: Adding input device Elan Touchpad (/dev/input/mouse0)

[     6.458] (II) No input driver specified, ignoring this device.

[     6.458] (II) This device may have been added with another device file.

[     6.458] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event10)

[     6.458] (II) No input driver specified, ignoring this device.

[     6.458] (II) This device may have been added with another device file.

[     6.459] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event11)

[     6.459] (II) No input driver specified, ignoring this device.

[     6.459] (II) This device may have been added with another device file.

[     6.459] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event12)

[     6.459] (II) No input driver specified, ignoring this device.

[     6.459] (II) This device may have been added with another device file.

[     6.460] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event13)

[     6.460] (II) No input driver specified, ignoring this device.

[     6.460] (II) This device may have been added with another device file.

[     6.460] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event14)

[     6.460] (II) No input driver specified, ignoring this device.

[     6.460] (II) This device may have been added with another device file.

[     6.461] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=8 (/dev/input/event15)

[     6.461] (II) No input driver specified, ignoring this device.

[     6.461] (II) This device may have been added with another device file.

[     6.461] (II) config/udev: Adding input device Asus WMI hotkeys (/dev/input/event7)

[     6.461] (**) Asus WMI hotkeys: Applying InputClass "libinput keyboard catchall"

[     6.461] (II) Using input driver 'libinput' for 'Asus WMI hotkeys'

[     6.461] (**) Asus WMI hotkeys: always reports core events

[     6.461] (**) Option "Device" "/dev/input/event7"

[     6.461] (**) Option "_source" "server/udev"

[     6.462] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is tagged by udev as: Keyboard

[     6.462] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is a keyboard

[     6.480] (**) Option "config_info" "udev:/sys/devices/platform/asus-nb-wmi/input/input7/event7"

[     6.480] (II) XINPUT: Adding extended input device "Asus WMI hotkeys" (type: KEYBOARD, id 13)

[     6.480] (**) Option "xkb_model" "pc105"

[     6.480] (**) Option "xkb_layout" "fr"

[     6.480] (**) Option "xkb_variant" "latin9"

[     6.481] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is tagged by udev as: Keyboard

[     6.481] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is a keyboard

[     6.481] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)

[     6.481] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"

[     6.482] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'

[     6.482] (**) AT Translated Set 2 keyboard: always reports core events

[     6.482] (**) Option "Device" "/dev/input/event0"

[     6.482] (**) Option "_source" "server/udev"

[     6.482] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard

[     6.482] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard

[     6.512] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"

[     6.512] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 14)

[     6.512] (**) Option "xkb_model" "pc105"

[     6.512] (**) Option "xkb_layout" "fr"

[     6.512] (**) Option "xkb_variant" "latin9"

[     6.513] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard

[     6.513] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard

[     6.513] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)

[     6.513] (II) No input driver specified, ignoring this device.

[     6.513] (II) This device may have been added with another device file.

[    10.704] (II) AIGLX: Suspending AIGLX clients for VT switch

LOGS DANS /home/user/.local/share/xorg/Xorg.0.log

[    23.459] (--) Log file renamed from "/home/manahoar/.local/share/xorg/Xorg.pid-932.log" to "/home/manahoar/.local/share/xorg/Xorg.0.log"

[    23.460] 

X.Org X Server 1.19.2

Release Date: 2017-03-02

[    23.460] X Protocol Version 11, Revision 0

[    23.460] Build Operating System: Linux 3.16.0-4-amd64 x86_64 Debian

[    23.460] Current Operating System: Linux debian-mnhr 4.9.0-2-amd64 #1 SMP Debian 4.9.13-1 (2017-02-27) x86_64

[    23.460] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-2-amd64 root=UUID=d11a650c-29a7-47bc-99af-e1b4de5522ea ro quiet nouveau.modeset=0

[    23.460] Build Date: 03 March 2017  03:14:41PM

[    23.460] xorg-server 2:1.19.2-1 (https://www.debian.org/support) 

[    23.460] Current version of pixman: 0.34.0

[    23.460]  Before reporting problems, check http://wiki.x.org

  to make sure that you have the latest version.

[    23.460] Markers: (--) probed, (**) from config file, (==) default setting,

  (++) from command line, (!!) notice, (II) informational,

  (WW) warning, (EE) error, (NI) not implemented, (??) unknown.

[    23.460] (==) Log file: "/home/manahoar/.local/share/xorg/Xorg.0.log", Time: Wed Apr  5 12:54:15 2017

[    23.461] (==) Using system config directory "/usr/share/X11/xorg.conf.d"

[    23.462] (==) No Layout section.  Using the first Screen section.

[    23.462] (==) No screen section available. Using defaults.

[    23.462] (**) |-->Screen "Default Screen Section" (0)

[    23.462] (**) |   |-->Monitor "<default monitor>"

[    23.463] (==) No monitor specified for screen "Default Screen Section".

  Using a default monitor configuration.

[    23.463] (==) Automatically adding devices

[    23.463] (==) Automatically enabling devices

[    23.463] (==) Automatically adding GPU devices

[    23.463] (==) Max clients allowed: 256, resource mask: 0x1fffff

[    23.463] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.

[    23.463]  Entry deleted from font path.

[    23.463] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.

[    23.463]  Entry deleted from font path.

[    23.463] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.

[    23.463]  Entry deleted from font path.

[    23.463] (WW) The directory "/usr/share/fonts/X11/Type1" does not exist.

[    23.463]  Entry deleted from font path.

[    23.463] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.

[    23.463]  Entry deleted from font path.

[    23.463] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.

[    23.463]  Entry deleted from font path.

[    23.463] (==) FontPath set to:

  /usr/share/fonts/X11/misc,

  built-ins

[    23.463] (==) ModulePath set to "/usr/lib/xorg/modules"

[    23.463] (II) The server relies on udev to provide the list of input devices.

  If no devices become available, reconfigure udev or disable AutoAddDevices.

[    23.463] (II) Loader magic: 0x55bad4d55e00

[    23.463] (II) Module ABI versions:

[    23.463]  X.Org ANSI C Emulation: 0.4

[    23.463]  X.Org Video Driver: 23.0

[    23.463]  X.Org XInput driver : 24.1

[    23.463]  X.Org Server Extension : 10.0

[    23.465] (++) using VT number 2

[    23.469] (II) systemd-logind: took control of session /org/freedesktop/login1/session/_32

[    23.471] (II) xfree86: Adding drm device (/dev/dri/card0)

[    23.471] (II) systemd-logind: got fd for /dev/dri/card0 226:0 fd 12 paused 0

[    23.475] (--) PCI:*(0:0:2:0) 8086:191b:1043:1c5d rev 6, Mem @ 0xdd000000/16777216, 0xb0000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072

[    23.475] (--) PCI: (0:1:0:0) 10de:139b:1043:1c5d rev 162, Mem @ 0xde000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288

[    23.475] (II) LoadModule: "glx"

[    23.478] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so

[    23.482] (II) Module glx: vendor="X.Org Foundation"

[    23.482]  compiled for 1.19.2, module version = 1.0.0

[    23.482]  ABI class: X.Org Server Extension, version 10.0

[    23.482] (==) Matched modesetting as autoconfigured driver 0

[    23.482] (==) Matched fbdev as autoconfigured driver 1

[    23.482] (==) Matched vesa as autoconfigured driver 2

[    23.482] (==) Assigned the driver to the xf86ConfigLayout

[    23.482] (II) LoadModule: "modesetting"

[    23.482] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so

[    23.483] (II) Module modesetting: vendor="X.Org Foundation"

[    23.483]  compiled for 1.19.2, module version = 1.19.2

[    23.483]  Module class: X.Org Video Driver

[    23.483]  ABI class: X.Org Video Driver, version 23.0

[    23.483] (II) LoadModule: "fbdev"

[    23.483] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so

[    23.484] (II) Module fbdev: vendor="X.Org Foundation"

[    23.484]  compiled for 1.19.0, module version = 0.4.4

[    23.484]  Module class: X.Org Video Driver

[    23.484]  ABI class: X.Org Video Driver, version 23.0

[    23.484] (II) LoadModule: "vesa"

[    23.484] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so

[    23.485] (II) Module vesa: vendor="X.Org Foundation"

[    23.485]  compiled for 1.19.0, module version = 2.3.4

[    23.485]  Module class: X.Org Video Driver

[    23.485]  ABI class: X.Org Video Driver, version 23.0

[    23.485] (II) modesetting: Driver for Modesetting Kernel Drivers: kms

[    23.485] (II) FBDEV: driver for framebuffer: fbdev

[    23.485] (II) VESA: driver for VESA chipsets: vesa

[    23.485] xf86EnableIOPorts: failed to set IOPL for I/O (Operation not permitted)

[    23.485] (II) modeset(0): using drv /dev/dri/card0

[    23.485] (WW) Falling back to old probe method for fbdev

[    23.486] (II) Loading sub module "fbdevhw"

[    23.486] (II) LoadModule: "fbdevhw"

[    23.486] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so

[    23.486] (II) Module fbdevhw: vendor="X.Org Foundation"

[    23.486]  compiled for 1.19.2, module version = 0.0.2

[    23.486]  ABI class: X.Org Video Driver, version 23.0

[    23.486] (WW) Falling back to old probe method for vesa

[    23.486] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support

[    23.486] (II) modeset(0): Creating default Display subsection in Screen section

  "Default Screen Section" for depth/fbbpp 24/32

[    23.487] (==) modeset(0): Depth 24, (==) framebuffer bpp 32

[    23.487] (==) modeset(0): RGB weight 888

[    23.487] (==) modeset(0): Default visual is TrueColor

[    23.487] (II) Loading sub module "glamoregl"

[    23.487] (II) LoadModule: "glamoregl"

[    23.487] (II) Loading /usr/lib/xorg/modules/libglamoregl.so

[    23.496] (II) Module glamoregl: vendor="X.Org Foundation"

[    23.496]  compiled for 1.19.2, module version = 1.0.0

[    23.496]  ABI class: X.Org ANSI C Emulation, version 0.4

[    23.496] (II) glamor: OpenGL accelerated X.org driver based.

[    23.510] (II) glamor: EGL version 1.4 (DRI2):

[    23.511] (II) modeset(0): glamor initialized

[    23.512] (II) modeset(0): Output eDP-1 has no monitor section

[    23.514] (II) modeset(0): Output DP-1 has no monitor section

[    23.638] (II) modeset(0): Output HDMI-1 has no monitor section

[    23.639] (II) modeset(0): Output HDMI-2 has no monitor section

[    23.642] (II) modeset(0): Output DP-2 has no monitor section

[    23.764] (II) modeset(0): Output HDMI-3 has no monitor section

[    23.764] (II) modeset(0): EDID for output eDP-1

[    23.765] (II) modeset(0): Manufacturer: AUO  Model: 38ed  Serial#: 0

[    23.765] (II) modeset(0): Year: 2014  Week: 43

[    23.765] (II) modeset(0): EDID Version: 1.4

[    23.765] (II) modeset(0): Digital Display Input

[    23.765] (II) modeset(0): 6 bits per channel

[    23.765] (II) modeset(0): Digital interface is DisplayPort

[    23.765] (II) modeset(0): Max Image Size [cm]: horiz.: 34  vert.: 19

[    23.765] (II) modeset(0): Gamma: 2.20

[    23.765] (II) modeset(0): No DPMS capabilities specified

[    23.765] (II) modeset(0): Supported color encodings: RGB 4:4:4 

[    23.765] (II) modeset(0): First detailed timing is preferred mode

[    23.765] (II) modeset(0): Preferred mode is native pixel format and refresh rate

[    23.765] (II) modeset(0): redX: 0.575 redY: 0.345   greenX: 0.340 greenY: 0.560

[    23.765] (II) modeset(0): blueX: 0.156 blueY: 0.123   whiteX: 0.313 whiteY: 0.329

[    23.765] (II) modeset(0): Manufacturer's mask: 0

[    23.765] (II) modeset(0): Supported detailed timing:

[    23.765] (II) modeset(0): clock: 142.0 MHz   Image Size:  344 x 193 mm

[    23.765] (II) modeset(0): h_active: 1920  h_sync: 2028  h_sync_end 2076 h_blank_end 2100 h_border: 0

[    23.765] (II) modeset(0): v_active: 1080  v_sync: 1090  v_sync_end 1100 v_blanking: 1126 v_border: 0

[    23.765] (II) modeset(0): Unknown vendor-specific block f

[    23.765] (II) modeset(0):  AUO

[    23.765] (II) modeset(0):  B156HTN03.8

[    23.765] (II) modeset(0): EDID (in hex):

[    23.765] (II) modeset(0):   00ffffffffffff0006afed3800000000

[    23.765] (II) modeset(0):   2b180104952213780251259358578f28

[    23.765] (II) modeset(0):   1f505400000001010101010101010101

[    23.765] (II) modeset(0):   010101010101783780b470382e406c30

[    23.765] (II) modeset(0):   aa0058c1100000180000000f00000000

[    23.765] (II) modeset(0):   00000000000000000020000000fe0041

[    23.765] (II) modeset(0):   554f0a202020202020202020000000fe

[    23.765] (II) modeset(0):   004231353648544e30332e38200a00e9

[    23.765] (II) modeset(0): Printing probed modes for output eDP-1

[    23.765] (II) modeset(0): Modeline "1920x1080"x60.1  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[    23.765] (II) modeset(0): Modeline "1920x1080"x59.9  138.50  1920 1968 2000 2080  1080 1083 1088 1111 +hsync -vsync (66.6 kHz d)

[    23.765] (II) modeset(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz d)

[    23.765] (II) modeset(0): Modeline "1680x1050"x59.9  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz d)

[    23.765] (II) modeset(0): Modeline "1600x1024"x60.2  103.12  1600 1600 1656 1664  1024 1024 1029 1030 +hsync +vsync (62.0 kHz d)

[    23.765] (II) modeset(0): Modeline "1400x1050"x60.0  122.00  1400 1488 1640 1880  1050 1052 1064 1082 +hsync +vsync (64.9 kHz d)

[    23.766] (II) modeset(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz d)

[    23.766] (II) modeset(0): Modeline "1440x900"x59.9  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz d)

[    23.766] (II) modeset(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz d)

[    23.766] (II) modeset(0): Modeline "1360x768"x59.8   84.75  1360 1432 1568 1776  768 771 781 798 -hsync +vsync (47.7 kHz d)

[    23.766] (II) modeset(0): Modeline "1360x768"x60.0   72.00  1360 1408 1440 1520  768 771 781 790 +hsync -vsync (47.4 kHz d)

[    23.766] (II) modeset(0): Modeline "1152x864"x60.0   81.62  1152 1216 1336 1520  864 865 868 895 -hsync +vsync (53.7 kHz d)

[    23.766] (II) modeset(0): Modeline "1024x768"x120.1  133.47  1024 1100 1212 1400  768 768 770 794 doublescan -hsync +vsync (95.3 kHz d)

[    23.766] (II) modeset(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz d)

[    23.766] (II) modeset(0): Modeline "960x720"x120.0  117.00  960 1024 1128 1300  720 720 722 750 doublescan -hsync +vsync (90.0 kHz d)

[    23.766] (II) modeset(0): Modeline "928x696"x120.1  109.15  928 976 1088 1264  696 696 698 719 doublescan -hsync +vsync (86.4 kHz d)

[    23.766] (II) modeset(0): Modeline "896x672"x120.0  102.40  896 960 1060 1224  672 672 674 697 doublescan -hsync +vsync (83.7 kHz d)

[    23.766] (II) modeset(0): Modeline "960x600"x120.0   77.00  960 984 1000 1040  600 601 604 617 doublescan +hsync -vsync (74.0 kHz d)

[    23.766] (II) modeset(0): Modeline "960x540"x120.0   69.25  960 984 1000 1040  540 541 544 555 doublescan +hsync -vsync (66.6 kHz d)

[    23.766] (II) modeset(0): Modeline "800x600"x120.0   81.00  800 832 928 1080  600 600 602 625 doublescan +hsync +vsync (75.0 kHz d)

[    23.766] (II) modeset(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz d)

[    23.766] (II) modeset(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz d)

[    23.766] (II) modeset(0): Modeline "840x525"x120.0   73.12  840 892 980 1120  525 526 529 544 doublescan -hsync +vsync (65.3 kHz d)

[    23.766] (II) modeset(0): Modeline "840x525"x119.8   59.50  840 864 880 920  525 526 529 540 doublescan +hsync -vsync (64.7 kHz d)

[    23.766] (II) modeset(0): Modeline "800x512"x120.3   51.56  800 800 828 832  512 512 514 515 doublescan +hsync +vsync (62.0 kHz d)

[    23.766] (II) modeset(0): Modeline "700x525"x120.0   61.00  700 744 820 940  525 526 532 541 doublescan +hsync +vsync (64.9 kHz d)

[    23.766] (II) modeset(0): Modeline "640x512"x120.0   54.00  640 664 720 844  512 512 514 533 doublescan +hsync +vsync (64.0 kHz d)

[    23.766] (II) modeset(0): Modeline "720x450"x119.8   53.25  720 760 836 952  450 451 454 467 doublescan -hsync +vsync (55.9 kHz d)

[    23.766] (II) modeset(0): Modeline "640x480"x120.0   54.00  640 688 744 900  480 480 482 500 doublescan +hsync +vsync (60.0 kHz d)

[    23.766] (II) modeset(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz d)

[    23.766] (II) modeset(0): Modeline "680x384"x119.6   42.38  680 716 784 888  384 385 390 399 doublescan -hsync +vsync (47.7 kHz d)

[    23.766] (II) modeset(0): Modeline "680x384"x119.9   36.00  680 704 720 760  384 385 390 395 doublescan +hsync -vsync (47.4 kHz d)

[    23.766] (II) modeset(0): Modeline "576x432"x120.1   40.81  576 608 668 760  432 432 434 447 doublescan -hsync +vsync (53.7 kHz d)

[    23.766] (II) modeset(0): Modeline "512x384"x120.0   32.50  512 524 592 672  384 385 388 403 doublescan -hsync -vsync (48.4 kHz d)

[    23.766] (II) modeset(0): Modeline "400x300"x120.6   20.00  400 420 484 528  300 300 302 314 doublescan +hsync +vsync (37.9 kHz d)

[    23.766] (II) modeset(0): Modeline "400x300"x112.7   18.00  400 412 448 512  300 300 301 312 doublescan +hsync +vsync (35.2 kHz d)

[    23.766] (II) modeset(0): Modeline "320x240"x120.1   12.59  320 328 376 400  240 245 246 262 doublescan -hsync -vsync (31.5 kHz d)

[    23.768] (II) modeset(0): EDID for output DP-1

[    23.892] (II) modeset(0): EDID for output HDMI-1

[    23.893] (II) modeset(0): EDID for output HDMI-2

[    23.895] (II) modeset(0): EDID for output DP-2

[    24.016] (II) modeset(0): EDID for output HDMI-3

[    24.016] (II) modeset(0): Output eDP-1 connected

[    24.016] (II) modeset(0): Output DP-1 disconnected

[    24.016] (II) modeset(0): Output HDMI-1 disconnected

[    24.016] (II) modeset(0): Output HDMI-2 disconnected

[    24.016] (II) modeset(0): Output DP-2 disconnected

[    24.016] (II) modeset(0): Output HDMI-3 disconnected

[    24.016] (II) modeset(0): Using exact sizes for initial modes

[    24.016] (II) modeset(0): Output eDP-1 using initial mode 1920x1080 +0+0

[    24.016] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)

[    24.016] (==) modeset(0): DPI set to (96, 96)

[    24.016] (II) Loading sub module "fb"

[    24.016] (II) LoadModule: "fb"

[    24.016] (II) Loading /usr/lib/xorg/modules/libfb.so

[    24.018] (II) Module fb: vendor="X.Org Foundation"

[    24.018]  compiled for 1.19.2, module version = 1.0.0

[    24.018]  ABI class: X.Org ANSI C Emulation, version 0.4

[    24.018] (II) UnloadModule: "fbdev"

[    24.018] (II) Unloading fbdev

[    24.018] (II) UnloadSubModule: "fbdevhw"

[    24.018] (II) Unloading fbdevhw

[    24.018] (II) UnloadModule: "vesa"

[    24.018] (II) Unloading vesa

[    24.018] (==) Depth 24 pixmap format is 32 bpp

[    24.089] (==) modeset(0): Backing store enabled

[    24.089] (==) modeset(0): Silken mouse enabled

[    24.089] (II) modeset(0): RandR 1.2 enabled, ignore the following RandR disabled message.

[    24.090] (==) modeset(0): DPMS enabled

[    24.091] (II) modeset(0): [DRI2] Setup complete

[    24.091] (II) modeset(0): [DRI2]   DRI driver: i965

[    24.091] (II) modeset(0): [DRI2]   VDPAU driver: i965

[    24.091] (--) RandR disabled

[    24.093] (II) SELinux: Disabled on system

[    24.097] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer

[    24.097] (II) AIGLX: enabled GLX_ARB_create_context

[    24.097] (II) AIGLX: enabled GLX_ARB_create_context_profile

[    24.097] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile

[    24.097] (II) AIGLX: enabled GLX_INTEL_swap_event

[    24.097] (II) AIGLX: enabled GLX_SGI_swap_control

[    24.097] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB

[    24.097] (II) AIGLX: enabled GLX_ARB_fbconfig_float

[    24.097] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float

[    24.097] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects

[    24.097] (II) AIGLX: enabled GLX_ARB_create_context_robustness

[    24.097] (II) AIGLX: Loaded and initialized i965

[    24.097] (II) GLX: Initialized DRI2 GL provider for screen 0

[    24.099] (II) modeset(0): Damage tracking initialized

[    24.099] (II) modeset(0): Setting screen physical size to 508 x 285

[    24.124] (II) config/udev: Adding input device Power Button (/dev/input/event3)

[    24.124] (**) Power Button: Applying InputClass "libinput keyboard catchall"

[    24.124] (II) LoadModule: "libinput"

[    24.124] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so

[    24.126] (II) Module libinput: vendor="X.Org Foundation"

[    24.126]  compiled for 1.19.0, module version = 0.23.0

[    24.126]  Module class: X.Org XInput Driver

[    24.126]  ABI class: X.Org XInput driver, version 24.1

[    24.126] (II) Using input driver 'libinput' for 'Power Button'

[    24.126] (II) systemd-logind: got fd for /dev/input/event3 13:67 fd 21 paused 0

[    24.126] (**) Power Button: always reports core events

[    24.126] (**) Option "Device" "/dev/input/event3"

[    24.127] (**) Option "_source" "server/udev"

[    24.127] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard

[    24.127] (II) input device 'Power Button', /dev/input/event3 is a keyboard

[    24.127] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"

[    24.127] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)

[    24.127] (**) Option "xkb_model" "pc105"

[    24.127] (**) Option "xkb_layout" "fr"

[    24.127] (**) Option "xkb_variant" "latin9"

[    24.139] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard

[    24.139] (II) input device 'Power Button', /dev/input/event3 is a keyboard

[    24.139] (II) config/udev: Adding input device Asus Wireless Radio Control (/dev/input/event4)

[    24.139] (**) Asus Wireless Radio Control: Applying InputClass "libinput keyboard catchall"

[    24.139] (II) Using input driver 'libinput' for 'Asus Wireless Radio Control'

[    24.140] (II) systemd-logind: got fd for /dev/input/event4 13:68 fd 24 paused 0

[    24.140] (**) Asus Wireless Radio Control: always reports core events

[    24.140] (**) Option "Device" "/dev/input/event4"

[    24.140] (**) Option "_source" "server/udev"

[    24.140] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is tagged by udev as: Keyboard

[    24.140] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is a keyboard

[    24.140] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/ATK4002:00/input/input4/event4"

[    24.140] (II) XINPUT: Adding extended input device "Asus Wireless Radio Control" (type: KEYBOARD, id 7)

[    24.140] (**) Option "xkb_model" "pc105"

[    24.140] (**) Option "xkb_layout" "fr"

[    24.140] (**) Option "xkb_variant" "latin9"

[    24.140] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is tagged by udev as: Keyboard

[    24.140] (II) input device 'Asus Wireless Radio Control', /dev/input/event4 is a keyboard

[    24.140] (II) config/udev: Adding input device Video Bus (/dev/input/event8)

[    24.140] (**) Video Bus: Applying InputClass "libinput keyboard catchall"

[    24.140] (II) Using input driver 'libinput' for 'Video Bus'

[    24.141] (II) systemd-logind: got fd for /dev/input/event8 13:72 fd 25 paused 0

[    24.141] (**) Video Bus: always reports core events

[    24.141] (**) Option "Device" "/dev/input/event8"

[    24.141] (**) Option "_source" "server/udev"

[    24.141] (II) input device 'Video Bus', /dev/input/event8 is tagged by udev as: Keyboard

[    24.141] (II) input device 'Video Bus', /dev/input/event8 is a keyboard

[    24.141] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8/event8"

[    24.141] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)

[    24.141] (**) Option "xkb_model" "pc105"

[    24.141] (**) Option "xkb_layout" "fr"

[    24.141] (**) Option "xkb_variant" "latin9"

[    24.141] (II) input device 'Video Bus', /dev/input/event8 is tagged by udev as: Keyboard

[    24.141] (II) input device 'Video Bus', /dev/input/event8 is a keyboard

[    24.142] (II) config/udev: Adding input device Video Bus (/dev/input/event9)

[    24.142] (**) Video Bus: Applying InputClass "libinput keyboard catchall"

[    24.142] (II) Using input driver 'libinput' for 'Video Bus'

[    24.142] (II) systemd-logind: got fd for /dev/input/event9 13:73 fd 26 paused 0

[    24.142] (**) Video Bus: always reports core events

[    24.142] (**) Option "Device" "/dev/input/event9"

[    24.142] (**) Option "_source" "server/udev"

[    24.142] (II) input device 'Video Bus', /dev/input/event9 is tagged by udev as: Keyboard

[    24.142] (II) input device 'Video Bus', /dev/input/event9 is a keyboard

[    24.142] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:12/LNXVIDEO:01/input/input9/event9"

[    24.142] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 9)

[    24.142] (**) Option "xkb_model" "pc105"

[    24.142] (**) Option "xkb_layout" "fr"

[    24.142] (**) Option "xkb_variant" "latin9"

[    24.143] (II) input device 'Video Bus', /dev/input/event9 is tagged by udev as: Keyboard

[    24.143] (II) input device 'Video Bus', /dev/input/event9 is a keyboard

[    24.143] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)

[    24.143] (II) No input driver specified, ignoring this device.

[    24.143] (II) This device may have been added with another device file.

[    24.143] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)

[    24.143] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"

[    24.143] (II) Using input driver 'libinput' for 'Sleep Button'

[    24.143] (II) systemd-logind: got fd for /dev/input/event2 13:66 fd 27 paused 0

[    24.143] (**) Sleep Button: always reports core events

[    24.143] (**) Option "Device" "/dev/input/event2"

[    24.143] (**) Option "_source" "server/udev"

[    24.143] (II) input device 'Sleep Button', /dev/input/event2 is tagged by udev as: Keyboard

[    24.143] (II) input device 'Sleep Button', /dev/input/event2 is a keyboard

[    24.144] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2/event2"

[    24.144] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 10)

[    24.144] (**) Option "xkb_model" "pc105"

[    24.144] (**) Option "xkb_layout" "fr"

[    24.144] (**) Option "xkb_variant" "latin9"

[    24.144] (II) input device 'Sleep Button', /dev/input/event2 is tagged by udev as: Keyboard

[    24.144] (II) input device 'Sleep Button', /dev/input/event2 is a keyboard

[    24.144] (II) config/udev: Adding input device USB2.0 HD UVC WebCam (/dev/input/event6)

[    24.144] (**) USB2.0 HD UVC WebCam: Applying InputClass "libinput keyboard catchall"

[    24.144] (II) Using input driver 'libinput' for 'USB2.0 HD UVC WebCam'

[    24.145] (II) systemd-logind: got fd for /dev/input/event6 13:70 fd 28 paused 0

[    24.145] (**) USB2.0 HD UVC WebCam: always reports core events

[    24.145] (**) Option "Device" "/dev/input/event6"

[    24.145] (**) Option "_source" "server/udev"

[    24.145] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is tagged by udev as: Keyboard

[    24.145] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is a keyboard

[    24.145] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/input/input6/event6"

[    24.145] (II) XINPUT: Adding extended input device "USB2.0 HD UVC WebCam" (type: KEYBOARD, id 11)

[    24.145] (**) Option "xkb_model" "pc105"

[    24.145] (**) Option "xkb_layout" "fr"

[    24.145] (**) Option "xkb_variant" "latin9"

[    24.146] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is tagged by udev as: Keyboard

[    24.146] (II) input device 'USB2.0 HD UVC WebCam', /dev/input/event6 is a keyboard

[    24.146] (II) config/udev: Adding input device Elan Touchpad (/dev/input/event10)

[    24.146] (**) Elan Touchpad: Applying InputClass "libinput touchpad catchall"

[    24.146] (II) Using input driver 'libinput' for 'Elan Touchpad'

[    24.146] (II) systemd-logind: got fd for /dev/input/event10 13:74 fd 29 paused 0

[    24.146] (**) Elan Touchpad: always reports core events

[    24.146] (**) Option "Device" "/dev/input/event10"

[    24.146] (**) Option "_source" "server/udev"

[    24.146] (II) input device 'Elan Touchpad', /dev/input/event10 is tagged by udev as: Touchpad

[    24.146] (II) input device 'Elan Touchpad', /dev/input/event10 is a touchpad

[    24.147] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-8/i2c-ELAN1000:00/input/input10/event10"

[    24.147] (II) XINPUT: Adding extended input device "Elan Touchpad" (type: TOUCHPAD, id 12)

[    24.147] (**) Option "AccelerationScheme" "none"

[    24.147] (**) Elan Touchpad: (accel) selected scheme none/0

[    24.147] (**) Elan Touchpad: (accel) acceleration factor: 2.000

[    24.147] (**) Elan Touchpad: (accel) acceleration threshold: 4

[    24.147] (II) input device 'Elan Touchpad', /dev/input/event10 is tagged by udev as: Touchpad

[    24.147] (II) input device 'Elan Touchpad', /dev/input/event10 is a touchpad

[    24.147] (II) config/udev: Adding input device Elan Touchpad (/dev/input/mouse0)

[    24.147] (II) No input driver specified, ignoring this device.

[    24.147] (II) This device may have been added with another device file.

[    24.147] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event11)

[    24.147] (II) No input driver specified, ignoring this device.

[    24.147] (II) This device may have been added with another device file.

[    24.148] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event12)

[    24.148] (II) No input driver specified, ignoring this device.

[    24.148] (II) This device may have been added with another device file.

[    24.148] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event13)

[    24.148] (II) No input driver specified, ignoring this device.

[    24.148] (II) This device may have been added with another device file.

[    24.148] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event14)

[    24.148] (II) No input driver specified, ignoring this device.

[    24.148] (II) This device may have been added with another device file.

[    24.148] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event15)

[    24.148] (II) No input driver specified, ignoring this device.

[    24.148] (II) This device may have been added with another device file.

[    24.148] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=8 (/dev/input/event16)

[    24.148] (II) No input driver specified, ignoring this device.

[    24.148] (II) This device may have been added with another device file.

[    24.148] (II) config/udev: Adding input device Asus WMI hotkeys (/dev/input/event7)

[    24.148] (**) Asus WMI hotkeys: Applying InputClass "libinput keyboard catchall"

[    24.148] (II) Using input driver 'libinput' for 'Asus WMI hotkeys'

[    24.149] (II) systemd-logind: got fd for /dev/input/event7 13:71 fd 30 paused 0

[    24.149] (**) Asus WMI hotkeys: always reports core events

[    24.149] (**) Option "Device" "/dev/input/event7"

[    24.149] (**) Option "_source" "server/udev"

[    24.149] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is tagged by udev as: Keyboard

[    24.149] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is a keyboard

[    24.149] (**) Option "config_info" "udev:/sys/devices/platform/asus-nb-wmi/input/input7/event7"

[    24.149] (II) XINPUT: Adding extended input device "Asus WMI hotkeys" (type: KEYBOARD, id 13)

[    24.149] (**) Option "xkb_model" "pc105"

[    24.149] (**) Option "xkb_layout" "fr"

[    24.149] (**) Option "xkb_variant" "latin9"

[    24.149] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is tagged by udev as: Keyboard

[    24.149] (II) input device 'Asus WMI hotkeys', /dev/input/event7 is a keyboard

[    24.149] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)

[    24.149] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"

[    24.149] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'

[    24.150] (II) systemd-logind: got fd for /dev/input/event0 13:64 fd 31 paused 0

[    24.150] (**) AT Translated Set 2 keyboard: always reports core events

[    24.150] (**) Option "Device" "/dev/input/event0"

[    24.150] (**) Option "_source" "server/udev"

[    24.150] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard

[    24.150] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard

[    24.150] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"

[    24.150] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 14)

[    24.150] (**) Option "xkb_model" "pc105"

[    24.150] (**) Option "xkb_layout" "fr"

[    24.150] (**) Option "xkb_variant" "latin9"

[    24.150] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard

[    24.150] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard

[    24.150] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)

[    24.150] (II) No input driver specified, ignoring this device.

[    24.150] (II) This device may have been added with another device file.

[    24.528] (II) modeset(0): EDID vendor "AUO", prod id 14573

[    24.528] (II) modeset(0): Printing DDC gathered Modelines:

[    24.528] (II) modeset(0): Modeline "1920x1080"x0.0  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[    25.840] (II) modeset(0): EDID vendor "AUO", prod id 14573

[    25.840] (II) modeset(0): Printing DDC gathered Modelines:

[    25.840] (II) modeset(0): Modeline "1920x1080"x0.0  142.00  1920 2028 2076 2100  1080 1090 1100 1126 -hsync -vsync (67.6 kHz eP)

[  2004.763] (**) Option "fd" "21"

[  2004.763] (**) Option "fd" "24"

[  2004.763] (**) Option "fd" "25"

[  2004.764] (**) Option "fd" "26"

[  2004.764] (**) Option "fd" "27"

[  2004.764] (**) Option "fd" "28"

[  2004.764] (**) Option "fd" "29"

[  2004.764] (**) Option "fd" "30"

[  2004.764] (**) Option "fd" "31"

[  2004.765] (II) UnloadModule: "libinput"

[  2004.765] (II) systemd-logind: releasing fd for 13:64

[  2004.940] (II) UnloadModule: "libinput"

[  2004.940] (II) systemd-logind: releasing fd for 13:71

[  2004.960] (II) UnloadModule: "libinput"

[  2004.960] (II) systemd-logind: releasing fd for 13:74

[  2004.992] (II) UnloadModule: "libinput"

[  2004.992] (II) systemd-logind: releasing fd for 13:70

[  2005.032] (II) UnloadModule: "libinput"

[  2005.032] (II) systemd-logind: releasing fd for 13:66

[  2005.048] (II) UnloadModule: "libinput"

[  2005.048] (II) systemd-logind: releasing fd for 13:73

[  2005.064] (II) UnloadModule: "libinput"

[  2005.064] (II) systemd-logind: releasing fd for 13:72

[  2005.080] (II) UnloadModule: "libinput"

[  2005.080] (II) systemd-logind: releasing fd for 13:68

[  2005.136] (II) UnloadModule: "libinput"

[  2005.136] (II) systemd-logind: releasing fd for 13:67

[  2005.440] (WW) xf86CloseConsole: KDSETMODE failed: Input/output error

[  2005.440] (WW) xf86CloseConsole: VT_GETMODE failed: Input/output error

[  2005.440] (WW) xf86CloseConsole: VT_ACTIVATE failed: Input/output error

[  2006.275] (II) Server terminated successfully (0). Closing log file.

Dernière modification par Manahoar (05-04-2017 15:59:16)

kyodev · 05-04-2017 13:55:21

anonyme a écrit :

pour gnome tu le trouve dans ton /home/user/.local/share/X11/Xorg.0.log (bon de tete , peut etre une erreur ), on le trouve aussi dans /usr/gdm3 (un truc comme ça tongue ) pour la suite si tu repasse a gnome

sur gnome3/stretch, j'ai

/home/user/.local/share/xorg/Xorg.0.log
/var/log/installer/Xorg.0.log

Manahoar · 05-04-2017 20:17:21

Yop !

Alors voilà, problème résolue !!

J'ai trouvé une solution sur internet sur un forum anglais alors de ce que j'ai compris, le problème du freeze venait du fait que le module nvidia n'était pas chargé. Je met la solution ici peut être que ceci pourrait aider quelqu'un qui avait le même problème que moi.

Arrivé sur gdm3, je me met en mode console Ctrl+Alt+F1 et j'entre cette commande:

modprobe nvidia

Je créer le fichier "nvidia.service" dans "/etc/systemd/system/"

vim  /etc/systemd/system/nvidia.service

[Unit]

Description=Nvidia Load

After=rc-local.service systemd-user-sessions.service

[Service]

ExecStart=/bin/sh -c "/sbin/modprobe nvidia"

[Install]

WantedBy=multi-user.target

J'enregistre et j'active donc ce service via cette commande en root

systemctl daemon-reload;systemctl enable nvidia.service

Created symlink /etc/systemd/system/multi-user.target.wants/nvidia.service -> /etc/systemd/system/nvidia.service.

source: https://bbs.archlinux.org/viewtopic.php … 0#p1619200

________________________________________________________________

Merci beaucoup pour l'aide apporté, j'espère que la solution trouvé sur un autre forum que j'ai publié ici pourra aider un autre débutant.

Dernière modification par Manahoar (05-04-2017 21:52:47)

Debian-facile

#1 05-04-2017 00:18:55

[RÉSOLU] Ecran freeze suite à installation bumblebee

#2 05-04-2017 00:26:04

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#3 05-04-2017 00:49:24

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#4 05-04-2017 01:00:23

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#5 05-04-2017 01:11:21

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#6 05-04-2017 01:13:43

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#7 05-04-2017 01:16:33

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#8 05-04-2017 01:20:47

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#9 05-04-2017 01:35:03

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#10 05-04-2017 01:47:19

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#11 05-04-2017 02:14:06

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#12 05-04-2017 02:19:02

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#13 05-04-2017 02:21:51

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#14 05-04-2017 02:23:52

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#15 05-04-2017 02:31:44

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#16 05-04-2017 02:40:34

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#17 05-04-2017 02:41:29

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#18 05-04-2017 02:59:33

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#19 05-04-2017 03:05:16

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#20 05-04-2017 03:07:45

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#21 05-04-2017 03:08:34

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#22 05-04-2017 13:19:12

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#23 05-04-2017 13:55:21

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

#24 05-04-2017 20:17:21

Re : [RÉSOLU] Ecran freeze suite à installation bumblebee

Pied de page des forums