Bonjour,
Voici le résultat ...étonnant ?
user@debian:~$ sudo badblocks -svwb 512 -o badblocks.list /dev/sda
Checking for bad blocks in read-write mode
From block 0 to 1953525167
Testing with pattern 0xaa: done
Reading and comparing: done
Testing with pattern 0x55: done
Reading and comparing: done
Testing with pattern 0xff: done
Reading and comparing: done
Testing with pattern 0x00: done
Reading and comparing: done
Pass completed, 0 bad blocks found. (0/0/0 errors)
Et un nouveau "smartctl":
user@debian:~$ sudo smartctl -a /dev/sda
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-4-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000.C
Device Model: Hitachi HDS721010CLA630
Serial Number: JP2940N102VPBV
LU WWN Device Id: 5 000cca 39cc14cee
Firmware Version: JP4OA41A
User Capacity: 1000204886016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Nov 26 14:02:01 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9753) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 163) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 069 016 Pre-fail Always - 0
2 Throughput_Performance 0x0027 135 093 054 Pre-fail Always - 98
3 Spin_Up_Time 0x0023 123 100 024 Pre-fail Always - 308 (Average 309)
4 Start_Stop_Count 0x0022 098 098 000 Old_age Always - 10392
5 Reallocated_Sector_Ct 0x0033 100 089 005 Pre-fail Always - 26 (0 23)
7 Seek_Error_Rate 0x002f 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 140 100 020 Pre-fail Offline - 30
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 5710
10 Spin_Retry_Count 0x0033 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 10375
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
185 Unknown_Attribute 0x0032 095 095 000 Old_age Always - 393215
187 Reported_Uncorrect 0x0032 098 098 000 Old_age Always - 2
188 Command_Timeout 0x0032 100 031 000 Old_age Always - 41819719
189 High_Fly_Writes 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 070 062 000 Old_age Always - 30 (Min/Max 17/31)
192 Power-Off_Retract_Count 0x0032 092 092 000 Old_age Always - 10393
193 Load_Cycle_Count 0x0032 092 092 000 Old_age Always - 10393
194 Temperature_Celsius 0x0002 200 157 000 Old_age Always - 30 (Min/Max 10/38)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 27
197 Current_Pending_Sector 0x0032 100 005 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 096 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 164 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 164 occurred at disk power-on lifetime: 5688 hours (237 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 40 c0 36 63 00 Error: IDNF at LBA = 0x006336c0 = 6502080
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 40 48 c0 36 63 40 00 5d+02:30:16.414 WRITE FPDMA QUEUED
61 40 40 80 36 63 40 00 5d+02:30:15.170 WRITE FPDMA QUEUED
61 40 38 40 36 63 40 00 5d+02:30:15.168 WRITE FPDMA QUEUED
61 40 30 00 36 63 40 00 5d+02:30:15.166 WRITE FPDMA QUEUED
61 40 28 c0 35 63 40 00 5d+02:30:15.164 WRITE FPDMA QUEUED
Error 163 occurred at disk power-on lifetime: 5686 hours (236 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 43 30 03 00 Error: UNC at LBA = 0x00033043 = 208963
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 01 90 43 30 03 40 00 4d+15:50:45.043 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 4d+15:50:45.041 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 4d+15:50:45.034 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 4d+15:50:45.033 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 4d+15:50:45.032 SET FEATURES [Enable SATA feature]
Error 162 occurred at disk power-on lifetime: 5686 hours (236 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 40 30 03 00 Error: UNC at LBA = 0x00033040 = 208960
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 01 00 43 30 03 40 00 4d+15:50:26.927 READ FPDMA QUEUED
60 01 e8 40 30 03 40 00 4d+15:50:26.927 READ FPDMA QUEUED
e5 00 00 00 00 00 00 00 4d+15:50:26.927 CHECK POWER MODE
ef 10 02 00 00 00 a0 00 4d+15:50:26.925 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 4d+15:50:26.918 IDENTIFY DEVICE
Error 161 occurred at disk power-on lifetime: 5686 hours (236 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 46 30 03 00 Error: UNC at LBA = 0x00033046 = 208966
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 01 50 43 30 03 40 00 4d+15:50:08.837 READ FPDMA QUEUED
60 01 48 40 30 03 40 00 4d+15:50:08.837 READ FPDMA QUEUED
60 01 40 46 30 03 40 00 4d+15:50:08.836 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 4d+15:50:08.835 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 4d+15:50:08.828 IDENTIFY DEVICE
Error 160 occurred at disk power-on lifetime: 5686 hours (236 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 45 30 03 00 Error: UNC at LBA = 0x00033045 = 208965
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 01 d0 43 30 03 40 00 4d+15:49:50.722 READ FPDMA QUEUED
60 01 c8 40 30 03 40 00 4d+15:49:50.722 READ FPDMA QUEUED
60 01 c0 46 30 03 40 00 4d+15:49:50.722 READ FPDMA QUEUED
60 01 b0 45 30 03 40 00 4d+15:49:50.722 READ FPDMA QUEUED
e5 00 00 00 00 00 00 00 4d+15:49:50.721 CHECK POWER MODE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5710 -
# 2 Short offline Completed: read failure 90% 5687 208963
# 3 Extended offline Completed: read failure 90% 5687 208963
# 4 Short offline Completed: read failure 90% 5684 208963
# 5 Short offline Completed: read failure 90% 5683 208963
# 6 Short offline Completed: read failure 90% 5679 62917
# 7 Short offline Completed: read failure 90% 5679 62917
# 8 Short offline Completed: read failure 90% 5679 62917
# 9 Short offline Completed without error 00% 2678 -
#10 Short offline Completed without error 00% 2660 -
#11 Short offline Completed without error 00% 2617 -
#12 Short offline Completed without error 00% 2590 -
#13 Short offline Completed without error 00% 2572 -
#14 Short offline Completed without error 00% 2556 -
#15 Short offline Completed without error 00% 2539 -
#16 Short offline Completed without error 00% 2524 -
#17 Short offline Completed without error 00% 2504 -
#18 Short offline Completed without error 00% 2481 -
#19 Short offline Completed without error 00% 2462 -
#20 Short offline Completed without error 00% 2425 -
#21 Short offline Completed without error 00% 2409 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Quel est votre verdict maintenant ?
Merci.