Bonjour,
Mon boulot vient de m'acheter un super écran : un Samsung 32" LU32R590CWEXXS.
Sauf que celui-ci n'est pas détecté par mon ordinateur portable Lenovo Y520-15IKBM-80YY.
Celui-ci est sous Linux Debian 10.9 il me semble (je ne sais pas comment vérifier ça) avec Mate.
Je suis à l'aise avec la ligne de commande mais je n'y connais pas grand chose dans l'administration matériel.
Donc merci de me dire exactement les commandes à taper.
Et si possible, les explications pour que je comprenne ce que je fais car j'aimerai bien m'améliorer dans ce domaine.
En attendant, voici le résultat de quelques commandes, que j'ai trouvé sur d'autres post et qui semblent souvent demandées dans ce genre de situation.
Linux taonix 4.19.0-16-amd64 #1 SMP Debian 4.19.181-1 (2021-03-19) x86_64 GNU/Linux
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v6/7th Gen Core Processor Host Bridge/DRAM Registers (rev 05)
Subsystem: Lenovo Xeon E3-1200 v6/7th Gen Core Processor Host Bridge/DRAM Registers
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information: Len=10 <?>
00:01.0 PCI bridge: Intel Corporation Skylake PCIe Controller (x16) (rev 05) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 122
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: a3000000-a40fffff
Prefetchable memory behind bridge: 0000000090000000-00000000a1ffffff
Capabilities: [88] Subsystem: Lenovo Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor PCIe Controller (x16)
Capabilities: [80] Power Management version 3
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [a0] Express Root Port (Slot+), MSI 00
Capabilities: [100] Virtual Channel
Capabilities: [140] Root Complex Link
Capabilities: [d94] #19
Kernel driver in use: pcieport
00:02.0 VGA compatible controller: Intel Corporation HD Graphics 630 (rev 04) (prog-if 00 [VGA controller])
Subsystem: Lenovo HD Graphics 630
Flags: bus master, fast devsel, latency 0, IRQ 130
Memory at a2000000 (64-bit, non-prefetchable) [size=16M]
Memory at b0000000 (64-bit, prefetchable) [size=256M]
I/O ports at 5000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: [40] Vendor Specific Information: Len=0c <?>
Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
Capabilities: [ac] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [d0] Power Management version 2
Capabilities: [100] Process Address Space ID (PASID)
Capabilities: [200] Address Translation Service (ATS)
Capabilities: [300] Page Request Interface (PRI)
Kernel driver in use: i915
Kernel modules: i915
00:14.0 USB controller: Intel Corporation Sunrise Point-H USB 3.0 xHCI Controller (rev 31) (prog-if 30 [XHCI])
Subsystem: Lenovo 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller
Flags: bus master, medium devsel, latency 0, IRQ 129
Memory at a4610000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:14.2 Signal processing controller: Intel Corporation Sunrise Point-H Thermal subsystem (rev 31)
Subsystem: Lenovo 100 Series/C230 Series Chipset Family Thermal Subsystem
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at a462a000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 3
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Kernel driver in use: intel_pch_thermal
Kernel modules: intel_pch_thermal
00:16.0 Communication controller: Intel Corporation Sunrise Point-H CSME HECI #1 (rev 31)
Subsystem: Lenovo 100 Series/C230 Series Chipset Family MEI Controller
Flags: bus master, fast devsel, latency 0, IRQ 136
Memory at a462b000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 3
Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
Kernel driver in use: mei_me
Kernel modules: mei_me
00:17.0 SATA controller: Intel Corporation Sunrise Point-H SATA Controller [AHCI mode] (rev 31) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo HM170/QM170 Chipset SATA Controller [AHCI Mode]
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 127
Memory at a4628000 (32-bit, non-prefetchable) [size=8K]
Memory at a462e000 (32-bit, non-prefetchable) [size=256]
I/O ports at 5080 [size=8]
I/O ports at 5088 [size=4]
I/O ports at 5060 [size=32]
Memory at a462c000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [70] Power Management version 3
Capabilities: [a8] SATA HBA v1.0
Kernel driver in use: ahci
Kernel modules: ahci
00:1c.0 PCI bridge: Intel Corporation Sunrise Point-H PCI Express Root Port #3 (rev f1) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 123
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: a4200000-a43fffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Illegal Vendor ID 100 Series/C230 Series Chipset Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Capabilities: [100] #00
Capabilities: [140] Access Control Services
Capabilities: [200] L1 PM Substates
Capabilities: [220] #19
Kernel driver in use: pcieport
00:1c.3 PCI bridge: Intel Corporation Sunrise Point-H PCI Express Root Port #4 (rev f1) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 124
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: a4500000-a45fffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Lenovo 100 Series/C230 Series Chipset Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Capabilities: [100] #00
Capabilities: [140] Access Control Services
Capabilities: [220] #19
Kernel driver in use: pcieport
00:1d.0 PCI bridge: Intel Corporation Sunrise Point-H PCI Express Root Port #9 (rev f1) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 125
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Memory behind bridge: a4400000-a44fffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Lenovo 100 Series/C230 Series Chipset Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Access Control Services
Capabilities: [200] L1 PM Substates
Capabilities: [220] #19
Kernel driver in use: pcieport
00:1f.0 ISA bridge: Intel Corporation Sunrise Point-H LPC Controller (rev 31)
Subsystem: Lenovo HM175 Chipset LPC/eSPI Controller
Flags: bus master, medium devsel, latency 0
00:1f.2 Memory controller: Intel Corporation Sunrise Point-H PMC (rev 31)
Subsystem: Lenovo 100 Series/C230 Series Chipset Family Power Management Controller
Flags: bus master, fast devsel, latency 0
Memory at a4624000 (32-bit, non-prefetchable) [size=16K]
00:1f.3 Audio device: Intel Corporation CM238 HD Audio Controller (rev 31)
Subsystem: Lenovo CM238 HD Audio Controller
Flags: bus master, fast devsel, latency 32, IRQ 137
Memory at a4620000 (64-bit, non-prefetchable) [size=16K]
Memory at a4600000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1f.4 SMBus: Intel Corporation Sunrise Point-H SMBus (rev 31)
Subsystem: Lenovo 100 Series/C230 Series Chipset Family SMBus
Flags: medium devsel, IRQ 16
Memory at a462d000 (64-bit, non-prefetchable) [size=256]
I/O ports at 5040 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
01:00.0 VGA compatible controller: NVIDIA Corporation GP106M [GeForce GTX 1060] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Lenovo GP106M [GeForce GTX 1060 Mobile] (GeForce GTX 1060 Max-Q 3GB)
Flags: bus master, fast devsel, latency 0, IRQ 131
Memory at a3000000 (32-bit, non-prefetchable) [size=16M]
Memory at 90000000 (64-bit, prefetchable) [size=256M]
Memory at a0000000 (64-bit, prefetchable) [size=32M]
I/O ports at 4000 [size=128]
Expansion ROM at a4080000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [78] Express Endpoint, MSI 00
Capabilities: [100] Virtual Channel
Capabilities: [250] Latency Tolerance Reporting
Capabilities: [258] L1 PM Substates
Capabilities: [128] Power Budgeting <?>
Capabilities: [420] Advanced Error Reporting
Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Capabilities: [900] #19
Kernel driver in use: nouveau
Kernel modules: nouveau
01:00.1 Audio device: NVIDIA Corporation GP106 High Definition Audio Controller (rev a1)
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at a4000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [78] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
02:00.0 Network controller: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter (rev 31)
Subsystem: Lenovo QCA9377 802.11ac Wireless Network Adapter
Flags: bus master, fast devsel, latency 0, IRQ 138
Memory at a4200000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit-
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [148] Virtual Channel
Capabilities: [168] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [178] Latency Tolerance Reporting
Capabilities: [180] L1 PM Substates
Kernel driver in use: ath10k_pci
Kernel modules: ath10k_pci
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 10)
Subsystem: Lenovo RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
Flags: bus master, fast devsel, latency 0, IRQ 19
I/O ports at 3000 [size=256]
Memory at a4504000 (64-bit, non-prefetchable) [size=4K]
Memory at a4500000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Capabilities: [d0] Vital Product Data
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [170] Latency Tolerance Reporting
Capabilities: [178] L1 PM Substates
Kernel driver in use: r8169
Kernel modules: r8169
04:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961 (prog-if 02 [NVM Express])
Subsystem: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961
Flags: bus master, fast devsel, latency 0, IRQ 16, NUMA node 0
Memory at a4400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [b0] MSI-X: Enable+ Count=33 Masked-
Capabilities: [100] Advanced Error Reporting
Capabilities: [148] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [158] Power Budgeting <?>
Capabilities: [168] #19
Capabilities: [188] Latency Tolerance Reporting
Capabilities: [190] L1 PM Substates
Kernel driver in use: nvme
Kernel modules: nvme
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 8192 x 8192
eDP-1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axis) 344mm x 193mm
1920x1080 60.05*+ 60.01 59.97 59.96 59.93
1680x1050 59.95 59.88
1600x1024 60.17
1400x1050 59.98
1600x900 59.99 59.94 59.95 59.82
1280x1024 60.02
1440x900 59.89
1400x900 59.96 59.88
1280x960 60.00
1440x810 60.00 59.97
1368x768 59.88 59.85
1360x768 59.80 59.96
1280x800 59.99 59.97 59.81 59.91
1152x864 60.00
1280x720 60.00 59.99 59.86 59.74
1024x768 60.04 60.00
960x720 60.00
928x696 60.05
896x672 60.01
1024x576 59.95 59.96 59.90 59.82
960x600 59.93 60.00
960x540 59.96 59.99 59.63 59.82
800x600 60.00 60.32 56.25
840x525 60.01 59.88
864x486 59.92 59.57
800x512 60.17
700x525 59.98
800x450 59.95 59.82
640x512 60.02
720x450 59.89
700x450 59.96 59.88
640x480 60.00 59.94
720x405 59.51 58.99
684x384 59.88 59.85
680x384 59.80 59.96
640x400 59.88 59.98
576x432 60.06
640x360 59.86 59.83 59.84 59.32
512x384 60.00
512x288 60.00 59.92
480x270 59.63 59.82
400x300 60.32 56.34
432x243 59.92 59.57
320x240 60.05
360x202 59.51 59.13
320x180 59.84 59.32
[ 0.424888] pci 0000:00:1d.0: bridge window [mem 0xa4400000-0xa44fffff]
[ 0.424899] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.424900] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.424901] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.424902] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff window]
[ 0.424903] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff window]
[ 0.424904] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff window]
[ 0.424904] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff window]
[ 0.424905] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff window]
[ 0.424906] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff window]
[ 0.424907] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff window]
[ 0.424908] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff window]
[ 0.424909] pci_bus 0000:00: resource 15 [mem 0x80000000-0xdfffffff window]
[ 0.424910] pci_bus 0000:00: resource 16 [mem 0xfd000000-0xfe7fffff window]
[ 0.424911] pci_bus 0000:01: resource 0 [io 0x4000-0x4fff]
[ 0.424912] pci_bus 0000:01: resource 1 [mem 0xa3000000-0xa40fffff]
[ 0.424913] pci_bus 0000:01: resource 2 [mem 0x90000000-0xa1ffffff 64bit pref]
[ 0.424914] pci_bus 0000:02: resource 1 [mem 0xa4200000-0xa43fffff]
[ 0.424915] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
[ 0.424915] pci_bus 0000:03: resource 1 [mem 0xa4500000-0xa45fffff]
[ 0.424916] pci_bus 0000:04: resource 1 [mem 0xa4400000-0xa44fffff]
[ 0.425027] NET: Registered protocol family 2
[ 0.425155] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes)
[ 0.425206] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.425349] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.425437] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.425463] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.425498] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.425555] NET: Registered protocol family 1
[ 0.425558] NET: Registered protocol family 44
[ 0.425567] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.427213] pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
[ 0.427214] pci 0000:01:00.1: D0 power state depends on 0000:01:00.0
[ 0.427369] PCI: CLS 64 bytes, default 64
[ 0.427404] Unpacking initramfs...
[ 1.014570] Freeing initrd memory: 37340K
[ 1.064694] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.064698] software IO TLB: mapped [mem 0x75f15000-0x79f15000] (64MB)
[ 1.064751] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x23fa772cf26, max_idle_ns: 440795269835 ns
[ 1.064776] clocksource: Switched to clocksource tsc
[ 1.065320] Initialise system trusted keyrings
[ 1.065328] Key type blacklist registered
[ 1.065362] workingset: timestamp_bits=40 max_order=22 bucket_order=0
[ 1.066327] zbud: loaded
[ 1.202921] Key type asymmetric registered
[ 1.202922] Asymmetric key parser 'x509' registered
[ 1.202931] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 1.202947] io scheduler noop registered
[ 1.202948] io scheduler deadline registered
[ 1.202975] io scheduler cfq registered (default)
[ 1.202976] io scheduler mq-deadline registered
[ 1.203265] pcieport 0000:00:01.0: Signaling PME with IRQ 122
[ 1.203458] pcieport 0000:00:1c.0: Signaling PME with IRQ 123
[ 1.203662] pcieport 0000:00:1c.3: Signaling PME with IRQ 124
[ 1.203864] pcieport 0000:00:1d.0: Signaling PME with IRQ 125
[ 1.203895] pcieport 0000:00:1d.0: AER enabled with IRQ 125
[ 1.203963] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 1.203974] efifb: probing for efifb
[ 1.203985] efifb: framebuffer at 0xb0000000, using 8128k, total 8128k
[ 1.203986] efifb: mode is 1920x1080x32, linelength=7680, pages=1
[ 1.203986] efifb: scrolling: redraw
[ 1.203988] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.207743] Console: switching to colour frame buffer device 240x67
[ 1.211413] fb0: EFI VGA frame buffer device
[ 1.211420] intel_idle: MWAIT substates: 0x11142120
[ 1.211421] intel_idle: v0.4.1 model 0x9E
[ 1.211582] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 1.211838] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.212398] Linux agpgart interface v0.103
[ 1.212446] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[ 1.212446] AMD IOMMUv2 functionality not available on this system
[ 1.212703] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 1.216274] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.216280] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.216427] mousedev: PS/2 mouse device common for all mice
[ 1.216468] rtc_cmos 00:04: RTC can wake from S4
[ 1.216953] rtc_cmos 00:04: registered as rtc0
[ 1.216963] rtc_cmos 00:04: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.216969] intel_pstate: Intel P-state driver initializing
[ 1.217017] intel_pstate: Disabling energy efficiency optimization
[ 1.217276] intel_pstate: HWP enabled
[ 1.217297] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.217574] NET: Registered protocol family 10
[ 1.221803] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.223012] Segment Routing with IPv6
[ 1.223025] mip6: Mobile IPv6
[ 1.223026] NET: Registered protocol family 17
[ 1.223170] mpls_gso: MPLS GSO support
[ 1.223514] mce: Using 10 MCE banks
[ 1.223537] microcode: sig=0x906e9, pf=0x20, revision=0x8e
[ 1.223693] microcode: Microcode Update Driver: v2.2.
[ 1.223699] sched_clock: Marking stable (1223271171, 418516)->(1230470505, -6780818)
[ 1.223941] registered taskstats version 1
[ 1.223942] Loading compiled-in X.509 certificates
[ 1.247218] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
[ 1.247229] Loaded X.509 cert 'Debian Secure Boot Signer 2021 - linux: 4b6ef5abca669825178e052c84667ccbc0531f8c'
[ 1.248492] zswap: loaded using pool lzo/zbud
[ 1.248573] AppArmor: AppArmor sha1 policy hashing enabled
[ 1.249312] rtc_cmos 00:04: setting system clock to 2021-04-17 09:32:00 UTC (1618651920)
[ 1.250249] Freeing unused kernel image memory: 1600K
[ 1.269258] Write protecting the kernel read-only data: 16384k
[ 1.269861] Freeing unused kernel image memory: 2028K
[ 1.270109] Freeing unused kernel image memory: 768K
[ 1.275327] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 1.275328] x86/mm: Checking user space page tables
[ 1.280716] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 1.280718] Run /init as init process
[ 1.326659] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[ 1.326665] ACPI: Lid Switch [LID0]
[ 1.326699] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 1.326703] ACPI: Power Button [PWRB]
[ 1.326729] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 1.326735] ACPI: Power Button [PWRF]
[ 1.328461] wmi_bus wmi_bus-PNP0C14:00: WQ data block query control method not found
[ 1.328463] wmi_bus wmi_bus-PNP0C14:00: WQ data block query control method not found
[ 1.328464] wmi_bus wmi_bus-PNP0C14:00: WQ data block query control method not found
[ 1.328464] wmi_bus wmi_bus-PNP0C14:00: WQ data block query control method not found
[ 1.328569] acpi PNP0C14:02: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:01)
[ 1.334647] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[ 1.334693] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[ 1.338353] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 1.349732] cryptd: max_cpu_qlen set to 1000
[ 1.349802] SCSI subsystem initialized
[ 1.357179] ACPI: bus type USB registered
[ 1.357236] usbcore: registered new interface driver usbfs
[ 1.357240] usbcore: registered new interface driver hub
[ 1.357256] usbcore: registered new device driver usb
[ 1.362006] AVX2 version of gcm_enc/dec engaged.
[ 1.362007] AES CTR mode by8 optimization enabled
[ 1.373714] libphy: r8169: probed
[ 1.374152] r8169 0000:03:00.0 eth0: RTL8168g/8111g, 8c:16:45:08:0e:86, XID 50900800, IRQ 126
[ 1.374153] r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 1.375462] libata version 3.00 loaded.
[ 1.378890] nvme nvme0: pci function 0000:04:00.0
[ 1.379897] r8169 0000:03:00.0 enp3s0: renamed from eth0
[ 1.380753] ahci 0000:00:17.0: version 3.0
[ 1.384233] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.384237] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 1.385367] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000001109810
[ 1.391015] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x4 impl SATA mode
[ 1.391017] ahci 0000:00:17.0: flags: 64bit ncq sntf pm led clo only pio slum part ems deso sadm sds apst
[ 1.398819] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 1.399352] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 1.399353] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.399354] usb usb1: Product: xHCI Host Controller
[ 1.399355] usb usb1: Manufacturer: Linux 4.19.0-16-amd64 xhci-hcd
[ 1.399355] usb usb1: SerialNumber: 0000:00:14.0
[ 1.399403] scsi host0: ahci
[ 1.399563] scsi host1: ahci
[ 1.399676] scsi host2: ahci
[ 1.399712] ata1: DUMMY
[ 1.399712] ata2: DUMMY
[ 1.399715] ata3: SATA max UDMA/133 abar m2048@0xa462c000 port 0xa462c200 irq 127
[ 1.400049] hub 1-0:1.0: USB hub found
[ 1.400083] hub 1-0:1.0: 16 ports detected
[ 1.400660] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.400662] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 1.400664] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[ 1.400713] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[ 1.400714] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.400715] usb usb2: Product: xHCI Host Controller
[ 1.400715] usb usb2: Manufacturer: Linux 4.19.0-16-amd64 xhci-hcd
[ 1.400716] usb usb2: SerialNumber: 0000:00:14.0
[ 1.400835] hub 2-0:1.0: USB hub found
[ 1.400888] hub 2-0:1.0: 8 ports detected
[ 1.400977] usb: port power management may be unreliable
[ 1.415737] checking generic (b0000000 7f0000) vs hw (b0000000 10000000)
[ 1.415737] fb: switching to inteldrmfb from EFI VGA
[ 1.415749] Console: switching to colour dummy device 80x25
[ 1.415845] [drm] Replacing VGA console driver
[ 1.421979] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 1.421980] [drm] Driver supports precise vblank timestamp query.
[ 1.422726] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=io+mem
[ 1.422766] i915 0000:00:02.0: firmware: direct-loading firmware i915/kbl_dmc_ver1_04.bin
[ 1.423087] [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)
[ 1.444150] [drm] Initialized i915 1.6.0 20180719 for 0000:00:02.0 on minor 0
[ 1.444258] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[ 1.444266] ACPI: Video Device [PEGP] (multi-head: yes rom: yes post: no)
[ 1.444397] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:00/LNXVIDEO:00/input/input6
[ 1.446661] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 1.447107] ACPI Warning: \_SB.PCI0.GFX0._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20180810/nsarguments-66)
[ 1.447129] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input7
[ 1.447161] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20180810/nsarguments-66)
[ 1.447338] pci 0000:01:00.0: optimus capabilities: enabled, status dynamic power,
[ 1.447341] VGA switcheroo: detected Optimus DSM method \_SB_.PCI0.PEG0.PEGP handle
[ 1.447342] nouveau: detected PR support, will not use DSM
[ 1.447356] nouveau 0000:01:00.0: enabling device (0006 -> 0007)
[ 1.447603] nouveau 0000:01:00.0: NVIDIA GP106 (136000a1)
[ 1.448605] fbcon: inteldrmfb (fb0) is primary device
[ 1.478767] nouveau 0000:01:00.0: bios: version 86.06.51.00.08
[ 1.479019] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/sw_nonctx.bin
[ 1.479030] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/sw_ctx.bin
[ 1.479041] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/sw_bundle_init.bin
[ 1.479053] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/sw_method_init.bin
[ 1.521814] nouveau 0000:01:00.0: fb: 6144 MiB GDDR5
[ 1.586580] vga_switcheroo: enabled
[ 1.586763] [TTM] Zone kernel: Available graphics memory: 8158260 kiB
[ 1.586763] [TTM] Zone dma32: Available graphics memory: 2097152 kiB
[ 1.586763] [TTM] Initializing pool allocator
[ 1.586766] [TTM] Initializing DMA pool allocator
[ 1.586797] nouveau 0000:01:00.0: DRM: VRAM: 6144 MiB
[ 1.586797] nouveau 0000:01:00.0: DRM: GART: 536870912 MiB
[ 1.586799] nouveau 0000:01:00.0: DRM: BIT table 'A' not found
[ 1.586799] nouveau 0000:01:00.0: DRM: BIT table 'L' not found
[ 1.586800] nouveau 0000:01:00.0: DRM: TMDS table version 2.0
[ 1.586801] nouveau 0000:01:00.0: DRM: DCB version 4.1
[ 1.586802] nouveau 0000:01:00.0: DRM: DCB outp 00: 01800f46 04600010
[ 1.586803] nouveau 0000:01:00.0: DRM: DCB outp 01: 01000f42 00020010
[ 1.586803] nouveau 0000:01:00.0: DRM: DCB outp 05: 02022f62 00020010
[ 1.586804] nouveau 0000:01:00.0: DRM: DCB outp 10: 04855f96 04600020
[ 1.586805] nouveau 0000:01:00.0: DRM: DCB outp 11: 04055f92 00020020
[ 1.586805] nouveau 0000:01:00.0: DRM: DCB conn 00: 00001046
[ 1.586806] nouveau 0000:01:00.0: DRM: DCB conn 02: 00010261
[ 1.586806] nouveau 0000:01:00.0: DRM: DCB conn 05: 02000546
[ 1.617990] nvme0n1: p1 p2 p3
[ 1.632167] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 1.632167] [drm] Driver supports precise vblank timestamp query.
[ 1.633579] nouveau 0000:01:00.0: DRM: MM: using COPY for buffer copies
[ 1.715504] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.736723] usb 1-3: new full-speed USB device number 2 using xhci_hcd
[ 1.752499] ata3.00: ATA-10: ST1000LM035-1RK172, LCM2, max UDMA/100
[ 1.752500] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 1.801787] ata3.00: configured for UDMA/100
[ 1.821087] scsi 2:0:0:0: Direct-Access ATA ST1000LM035-1RK1 LCM2 PQ: 0 ANSI: 5
[ 1.829020] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/fecs_bl.bin
[ 1.829031] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/fecs_inst.bin
[ 1.829037] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/fecs_data.bin
[ 1.829043] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/fecs_sig.bin
[ 1.829055] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/gpccs_bl.bin
[ 1.829063] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/gpccs_inst.bin
[ 1.829069] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/gpccs_data.bin
[ 1.829075] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/gr/gpccs_sig.bin
[ 1.829097] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/sec2/image.bin
[ 1.829112] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/sec2/desc.bin
[ 1.829119] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/sec2/sig.bin
[ 1.829640] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/acr/ucode_load.bin
[ 1.829766] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/acr/ucode_unload.bin
[ 1.829848] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/acr/bl.bin
[ 1.829855] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/acr/unload_bl.bin
[ 1.829867] nouveau 0000:01:00.0: firmware: direct-loading firmware nvidia/gp106/nvdec/scrubber.bin
[ 1.887521] usb 1-3: New USB device found, idVendor=046d, idProduct=c52b, bcdDevice=12.01
[ 1.887522] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.887523] usb 1-3: Product: USB Receiver
[ 1.887524] usb 1-3: Manufacturer: Logitech
[ 1.893851] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.899138] usbcore: registered new interface driver usbhid
[ 1.899139] usbhid: USB HID core driver
[ 1.901246] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-3/input2
[ 2.016715] usb 1-6: new high-speed USB device number 3 using xhci_hcd
[ 2.022754] input: Logitech Unifying Device. Wireless PID:4069 Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.2/0003:046D:C52B.0003/0003:046D:4069.0004/input/input8
[ 2.022810] nouveau 0000:01:00.0: DRM: allocated 3840x2160 fb: 0x200000, bo 0000000000f4685e
[ 2.022866] input: Logitech Unifying Device. Wireless PID:4069 Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.2/0003:046D:C52B.0003/0003:046D:4069.0004/input/input9
[ 2.023018] input: Logitech Unifying Device. Wireless PID:4069 Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.2/0003:046D:C52B.0003/0003:046D:4069.0004/input/input10
[ 2.023034] input: Logitech Unifying Device. Wireless PID:4069 System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.2/0003:046D:C52B.0003/0003:046D:4069.0004/input/input11
[ 2.023145] hid-generic 0003:046D:4069.0004: input,hidraw1: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:4069] on usb-0000:00:14.0-3:2
[ 2.032504] input: Logitech Craft as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.2/0003:046D:C52B.0003/0003:046D:4066.0005/input/input15
[ 2.223854] usb 1-6: New USB device found, idVendor=04f2, idProduct=b57e, bcdDevice=87.40
[ 2.223855] usb 1-6: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 2.223855] usb 1-6: Product: EasyCamera
[ 2.223856] usb 1-6: Manufacturer: Chicony Electronics Co.,Ltd.
[ 2.223857] usb 1-6: SerialNumber: 0001
[ 2.232866] logitech-hidpp-device 0003:046D:4066.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech Craft] on usb-0000:00:14.0-3:3
[ 2.261415] psmouse serio1: synaptics: queried max coordinates: x [..5670], y [..4744]
[ 2.299607] psmouse serio1: synaptics: queried min coordinates: x [1272..], y [1108..]
[ 2.299610] psmouse serio1: synaptics: Your touchpad (PNP: SYN2b96 PNP0f03) says it can support a different bus. If i2c-hid and hid-rmi are not used, you might want to try setting psmouse.synaptics_intertouch to 1 and report this to linux-input@vger.kernel.org.
[ 2.328546] input: Logitech MX Master 2S as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.2/0003:046D:C52B.0003/0003:046D:4069.0004/input/input16
[ 2.328662] logitech-hidpp-device 0003:046D:4069.0004: input,hidraw1: USB HID v1.11 Keyboard [Logitech MX Master 2S] on usb-0000:00:14.0-3:2
[ 2.352729] usb 1-11: new full-speed USB device number 4 using xhci_hcd
[ 2.366351] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.2, id: 0x1e2b1, caps: 0xf00123/0x840300/0x26800/0x440000, board id: 3287, fw id: 2469908
[ 2.412652] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
[ 2.506066] usb 1-11: New USB device found, idVendor=0cf3, idProduct=e500, bcdDevice= 0.01
[ 2.506068] usb 1-11: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.563254] Console: switching to colour frame buffer device 240x67
[ 2.585431] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 2.585610] nouveau 0000:01:00.0: fb1: nouveaufb frame buffer device
[ 2.600804] [drm] Initialized nouveau 1.3.1 20120801 for 0000:01:00.0 on minor 1
[ 2.609475] sd 2:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 2.609477] sd 2:0:0:0: [sda] 4096-byte physical blocks
[ 2.609480] sd 2:0:0:0: [sda] Write Protect is off
[ 2.609481] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.609485] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.650995] sda: sda1
[ 2.651336] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.927453] PM: Image not found (code -22)
[ 3.050799] EXT4-fs (nvme0n1p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.156513] systemd[1]: Inserted module 'autofs4'
[ 3.255830] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 3.265010] pci_bus 0000:01: Allocating resources
[ 3.265801] pci_bus 0000:02: Allocating resources
[ 3.265955] pcieport 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 02] add_size 1000
[ 3.265956] pcieport 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000
[ 3.265964] pci_bus 0000:03: Allocating resources
[ 3.265971] pcieport 0000:00:1c.3: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000
[ 3.265979] pcieport 0000:00:1c.0: BAR 15: assigned [mem 0x80100000-0x802fffff 64bit pref]
[ 3.265984] pcieport 0000:00:1c.3: BAR 15: assigned [mem 0x80300000-0x804fffff 64bit pref]
[ 3.265986] pcieport 0000:00:1c.0: BAR 13: assigned [io 0x6000-0x6fff]
[ 3.266114] pci_bus 0000:04: Allocating resources
[ 3.266118] pcieport 0000:00:1d.0: bridge window [io 0x1000-0x0fff] to [bus 04] add_size 1000
[ 3.266119] pcieport 0000:00:1d.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 04] add_size 200000 add_align 100000
[ 3.266124] pcieport 0000:00:1d.0: BAR 15: assigned [mem 0x80500000-0x806fffff 64bit pref]
[ 3.266125] pcieport 0000:00:1d.0: BAR 13: assigned [io 0x7000-0x7fff]
[ 3.272769] systemd[1]: Detected architecture x86-64.
[ 3.276062] systemd[1]: Set hostname to <taonix>.
[ 3.347869] systemd[1]: Listening on Syslog Socket.
[ 3.348755] systemd[1]: Created slice User and Session Slice.
[ 3.348792] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 3.349130] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 3.349198] systemd[1]: Listening on udev Control Socket.
[ 3.349276] systemd[1]: Listening on Journal Audit Socket.
[ 3.349285] systemd[1]: Reached target User and Group Name Lookups.
[ 3.365588] lp: driver loaded but no devices found
[ 3.365830] EXT4-fs (nvme0n1p2): re-mounted. Opts: errors=remount-ro
[ 3.369684] ppdev: user-space parallel port driver
[ 3.475023] systemd-journald[287]: Received request to flush runtime journal from PID 1
[ 3.476621] ACPI: AC Adapter [ADP0] (on-line)
[ 3.539792] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 3.545807] mei_me 0000:00:16.0: enabling device (0000 -> 0002)
[ 3.547772] iTCO_vendor_support: vendor-support=0
[ 3.548578] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 3.548707] iTCO_wdt: Found a Intel PCH TCO device (Version=4, TCOBASE=0x0400)
[ 3.550930] alg: No test for fips(ansi_cprng) (fips_ansi_cprng)
[ 3.552958] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 3.581778] RAPL PMU: API unit is 2^-32 Joules, 5 fixed counters, 655360 ms ovfl timer
[ 3.581779] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[ 3.581779] RAPL PMU: hw unit of domain package 2^-14 Joules
[ 3.581780] RAPL PMU: hw unit of domain dram 2^-14 Joules
[ 3.581780] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[ 3.581781] RAPL PMU: hw unit of domain psys 2^-14 Joules
[ 3.584656] EFI Variables Facility v0.08 2004-May-17
[ 3.590122] media: Linux media interface: v0.10
[ 3.591137] Adding 1000444k swap on /dev/nvme0n1p3. Priority:-2 extents:1 across:1000444k SSFS
[ 3.592781] battery: ACPI: Battery Slot [BAT0] (battery present)
[ 3.596850] input: PC Speaker as /devices/platform/pcspkr/input/input17
[ 3.603649] input: Ideapad extra buttons as /devices/pci0000:00/0000:00:1f.0/PNP0C09:00/VPC2004:00/input/input18
[ 3.636548] videodev: Linux video capture interface: v2.00
[ 3.674735] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[ 3.674959] snd_hda_intel 0000:01:00.1: Disabling MSI
[ 3.674966] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
[ 3.693179] pstore: Using compression: deflate
[ 3.693190] pstore: Registered efi as persistent store backend
[ 3.702829] Bluetooth: Core ver 2.22
[ 3.702839] NET: Registered protocol family 31
[ 3.702840] Bluetooth: HCI device and connection manager initialized
[ 3.702842] Bluetooth: HCI socket layer initialized
[ 3.702843] Bluetooth: L2CAP socket layer initialized
[ 3.702847] Bluetooth: SCO socket layer initialized
[ 3.722596] usbcore: registered new interface driver btusb
[ 3.799732] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC233: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 3.799733] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 3.799734] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 3.799734] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
[ 3.799735] snd_hda_codec_realtek hdaudioC0D0: inputs:
[ 3.799736] snd_hda_codec_realtek hdaudioC0D0: Mic=0x19
[ 3.799737] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12
[ 3.806727] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 3.838088] uvcvideo: Found UVC 1.00 device EasyCamera (04f2:b57e)
[ 3.855695] input: EasyCamera: EasyCamera as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/input/input20
[ 3.855779] usbcore: registered new interface driver uvcvideo
[ 3.855780] USB Video Class driver (1.1.1)
[ 3.908744] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.935268] intel_rapl: Found RAPL domain package
[ 3.935270] intel_rapl: Found RAPL domain core
[ 3.935271] intel_rapl: Found RAPL domain uncore
[ 3.935273] intel_rapl: Found RAPL domain dram
[ 3.940939] audit: type=1400 audit(1618651923.187:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=508 comm="apparmor_parser"
[ 3.943178] audit: type=1400 audit(1618651923.187:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=510 comm="apparmor_parser"
[ 3.943181] audit: type=1400 audit(1618651923.187:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=510 comm="apparmor_parser"
[ 3.943183] audit: type=1400 audit(1618651923.187:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd//third_party" pid=510 comm="apparmor_parser"
[ 3.943485] audit: type=1400 audit(1618651923.187:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=512 comm="apparmor_parser"
[ 3.944355] audit: type=1400 audit(1618651923.187:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=511 comm="apparmor_parser"
[ 3.944358] audit: type=1400 audit(1618651923.187:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=511 comm="apparmor_parser"
[ 3.944360] audit: type=1400 audit(1618651923.187:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=511 comm="apparmor_parser"
[ 3.946488] audit: type=1400 audit(1618651923.191:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=516 comm="apparmor_parser"
[ 4.061669] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1f.3/sound/card0/input19
[ 4.061937] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input21
[ 4.062013] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input22
[ 4.087069] ath10k_pci 0000:02:00.0: firmware: failed to load ath10k/pre-cal-pci-0000:02:00.0.bin (-2)
[ 4.087119] firmware_class: See https://wiki.debian.org/Firmware for information about missing firmware
[ 4.087179] ath10k_pci 0000:02:00.0: firmware: failed to load ath10k/cal-pci-0000:02:00.0.bin (-2)
[ 4.089165] ath10k_pci 0000:02:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/firmware-6.bin
[ 4.089173] ath10k_pci 0000:02:00.0: qca9377 hw1.1 target 0x05020001 chip_id 0x003821ff sub 17aa:0901
[ 4.089175] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
[ 4.090017] ath10k_pci 0000:02:00.0: firmware ver WLAN.TF.2.1-00021-QCARMSWP-1 api 6 features wowlan,ignore-otp crc32 42e41877
[ 4.154897] ath10k_pci 0000:02:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/board-2.bin
[ 4.155252] ath10k_pci 0000:02:00.0: board_file api 2 bmi_id N/A crc32 8aedfa4a
[ 4.220611] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.220612] Bluetooth: BNEP filters: protocol multicast
[ 4.220614] Bluetooth: BNEP socket layer initialized
[ 4.405171] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 4.406684] r8169 0000:03:00.0: firmware: direct-loading firmware rtl_nic/rtl8168g-3.fw
[ 4.407537] Generic PHY r8169-300:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=r8169-300:00, irq=IGNORE)
[ 4.445059] pci_bus 0000:01: Allocating resources
[ 4.445875] pci_bus 0000:02: Allocating resources
[ 4.445907] pci_bus 0000:03: Allocating resources
[ 4.446103] pci_bus 0000:04: Allocating resources
[ 4.523087] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 4.565193] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input23
[ 4.565225] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input24
[ 4.565250] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input25
[ 4.768410] ath10k_pci 0000:02:00.0: Unknown eventid: 118809
[ 4.771319] ath10k_pci 0000:02:00.0: Unknown eventid: 90118
[ 4.772145] ath10k_pci 0000:02:00.0: htt-ver 3.56 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
[ 4.773990] ath: EEPROM regdomain: 0x6c
[ 4.773991] ath: EEPROM indicates we should expect a direct regpair map
[ 4.773993] ath: Country alpha2 being used: 00
[ 4.773994] ath: Regpair used: 0x6c
[ 4.788256] ath10k_pci 0000:02:00.0 wlp2s0: renamed from wlan0
[ 4.819889] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 4.860486] broken atomic modeset userspace detected, disabling atomic
[ 5.589989] ath10k_pci 0000:02:00.0: Unknown eventid: 118809
[ 5.592881] ath10k_pci 0000:02:00.0: Unknown eventid: 90118
[ 5.606111] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 6.379410] ath10k_pci 0000:02:00.0: Unknown eventid: 118809
[ 6.382314] ath10k_pci 0000:02:00.0: Unknown eventid: 90118
[ 6.393984] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 6.449320] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 11.278492] logitech-hidpp-device 0003:046D:4066.0005: HID++ 4.5 device connected.
[ 11.313766] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 16.194719] wlp2s0: authenticate with 50:c7:bf:be:d5:ea
[ 16.226468] wlp2s0: send auth to 50:c7:bf:be:d5:ea (try 1/3)
[ 16.227810] wlp2s0: authenticated
[ 16.228699] wlp2s0: associate with 50:c7:bf:be:d5:ea (try 1/3)
[ 16.230686] wlp2s0: RX AssocResp from 50:c7:bf:be:d5:ea (capab=0x1011 status=0 aid=3)
[ 16.233381] wlp2s0: associated
[ 16.244110] ath: EEPROM regdomain: 0x8114
[ 16.244112] ath: EEPROM indicates we should expect a country code
[ 16.244112] ath: doing EEPROM country->regdmn map search
[ 16.244113] ath: country maps to regdmn code: 0x37
[ 16.244114] ath: Country alpha2 being used: DE
[ 16.244115] ath: Regpair used: 0x37
[ 16.244116] ath: regdomain 0x8114 dynamically updated by country element
[ 16.278043] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[ 16.314862] wlp2s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 50:c7:bf:be:d5:ea
[ 19.949090] tun: Universal TUN/TAP device driver, 1.6
[ 23.041903] kauditd_printk_skb: 7 callbacks suppressed
[ 23.041904] audit: type=1400 audit(1618651942.287:18): apparmor="STATUS" operation="profile_load" profile="unconfined" name="docker-default" pid=1358 comm="apparmor_parser"
[ 23.267319] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 23.269608] Bridge firewalling registered
[ 23.429060] Initializing XFRM netlink socket
[ 23.498948] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready
[ 23.575174] IPv6: ADDRCONF(NETDEV_UP): br-d4b3d35cfebe: link is not ready
[ 23.890846] br-d4b3d35cfebe: port 1(veth6d4ed77) entered blocking state
[ 23.890848] br-d4b3d35cfebe: port 1(veth6d4ed77) entered disabled state
[ 23.891072] device veth6d4ed77 entered promiscuous mode
[ 23.891643] IPv6: ADDRCONF(NETDEV_UP): veth6d4ed77: link is not ready
[ 23.891647] br-d4b3d35cfebe: port 1(veth6d4ed77) entered blocking state
[ 23.891648] br-d4b3d35cfebe: port 1(veth6d4ed77) entered forwarding state
[ 23.891673] IPv6: ADDRCONF(NETDEV_CHANGE): br-d4b3d35cfebe: link becomes ready
[ 23.891851] br-d4b3d35cfebe: port 1(veth6d4ed77) entered disabled state
[ 23.903779] br-d4b3d35cfebe: port 2(veth36cb627) entered blocking state
[ 23.903781] br-d4b3d35cfebe: port 2(veth36cb627) entered disabled state
[ 23.903970] device veth36cb627 entered promiscuous mode
[ 23.908327] IPv6: ADDRCONF(NETDEV_UP): veth36cb627: link is not ready
[ 23.908333] br-d4b3d35cfebe: port 2(veth36cb627) entered blocking state
[ 23.908334] br-d4b3d35cfebe: port 2(veth36cb627) entered forwarding state
[ 23.971061] br-d4b3d35cfebe: port 3(veth2d0df4f) entered blocking state
[ 23.971062] br-d4b3d35cfebe: port 3(veth2d0df4f) entered disabled state
[ 23.971108] device veth2d0df4f entered promiscuous mode
[ 23.971172] IPv6: ADDRCONF(NETDEV_UP): veth2d0df4f: link is not ready
[ 23.971174] br-d4b3d35cfebe: port 3(veth2d0df4f) entered blocking state
[ 23.971174] br-d4b3d35cfebe: port 3(veth2d0df4f) entered forwarding state
[ 24.026619] br-d4b3d35cfebe: port 4(veth0902042) entered blocking state
[ 24.026621] br-d4b3d35cfebe: port 4(veth0902042) entered disabled state
[ 24.026681] device veth0902042 entered promiscuous mode
[ 24.026772] IPv6: ADDRCONF(NETDEV_UP): veth0902042: link is not ready
[ 24.026775] br-d4b3d35cfebe: port 4(veth0902042) entered blocking state
[ 24.026776] br-d4b3d35cfebe: port 4(veth0902042) entered forwarding state
[ 24.035098] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[ 24.131904] br-d4b3d35cfebe: port 5(veth11eca9f) entered blocking state
[ 24.131905] br-d4b3d35cfebe: port 5(veth11eca9f) entered disabled state
[ 24.132185] device veth11eca9f entered promiscuous mode
[ 24.133116] IPv6: ADDRCONF(NETDEV_UP): veth11eca9f: link is not ready
[ 24.133120] br-d4b3d35cfebe: port 5(veth11eca9f) entered blocking state
[ 24.133121] br-d4b3d35cfebe: port 5(veth11eca9f) entered forwarding state
[ 24.272933] eth0: renamed from vethc7a7a9c
[ 24.304951] br-d4b3d35cfebe: port 2(veth36cb627) entered disabled state
[ 24.305036] br-d4b3d35cfebe: port 3(veth2d0df4f) entered disabled state
[ 24.305066] br-d4b3d35cfebe: port 4(veth0902042) entered disabled state
[ 24.305111] br-d4b3d35cfebe: port 5(veth11eca9f) entered disabled state
[ 24.305127] IPv6: ADDRCONF(NETDEV_CHANGE): veth6d4ed77: link becomes ready
[ 24.305144] br-d4b3d35cfebe: port 1(veth6d4ed77) entered blocking state
[ 24.305145] br-d4b3d35cfebe: port 1(veth6d4ed77) entered forwarding state
[ 24.306265] br-d4b3d35cfebe: port 6(veth19f9bfc) entered blocking state
[ 24.306269] br-d4b3d35cfebe: port 6(veth19f9bfc) entered disabled state
[ 24.306393] device veth19f9bfc entered promiscuous mode
[ 24.306628] IPv6: ADDRCONF(NETDEV_UP): veth19f9bfc: link is not ready
[ 24.306631] br-d4b3d35cfebe: port 6(veth19f9bfc) entered blocking state
[ 24.306632] br-d4b3d35cfebe: port 6(veth19f9bfc) entered forwarding state
[ 24.447555] eth0: renamed from vetha642c4a
[ 24.469014] br-d4b3d35cfebe: port 6(veth19f9bfc) entered disabled state
[ 24.473299] IPv6: ADDRCONF(NETDEV_CHANGE): veth2d0df4f: link becomes ready
[ 24.473324] br-d4b3d35cfebe: port 3(veth2d0df4f) entered blocking state
[ 24.473326] br-d4b3d35cfebe: port 3(veth2d0df4f) entered forwarding state
[ 24.501055] eth0: renamed from vethed6acf7
[ 24.531766] IPv6: ADDRCONF(NETDEV_CHANGE): veth36cb627: link becomes ready
[ 24.531790] br-d4b3d35cfebe: port 2(veth36cb627) entered blocking state
[ 24.531792] br-d4b3d35cfebe: port 2(veth36cb627) entered forwarding state
[ 24.573173] eth0: renamed from vethf4fac99
[ 24.592921] IPv6: ADDRCONF(NETDEV_CHANGE): veth0902042: link becomes ready
[ 24.592945] br-d4b3d35cfebe: port 4(veth0902042) entered blocking state
[ 24.592946] br-d4b3d35cfebe: port 4(veth0902042) entered forwarding state
[ 24.719467] eth0: renamed from veth05f7718
[ 24.737329] IPv6: ADDRCONF(NETDEV_CHANGE): veth11eca9f: link becomes ready
[ 24.737355] br-d4b3d35cfebe: port 5(veth11eca9f) entered blocking state
[ 24.737356] br-d4b3d35cfebe: port 5(veth11eca9f) entered forwarding state
[ 24.773207] eth0: renamed from vethf363769
[ 24.793089] IPv6: ADDRCONF(NETDEV_CHANGE): veth19f9bfc: link becomes ready
[ 24.793117] br-d4b3d35cfebe: port 6(veth19f9bfc) entered blocking state
[ 24.793118] br-d4b3d35cfebe: port 6(veth19f9bfc) entered forwarding state
cat /etc/apt/sources.list
deb http://deb.debian.org/debian/ buster non-free contrib main
deb-src http://deb.debian.org/debian/ buster main contrib non-free
deb http://security.debian.org/debian-security/ buster/updates main
deb-src http://security.debian.org/debian-security/ buster/updates main
deb http://deb.debian.org/debian/ buster-updates main contrib non-free
deb-src http://deb.debian.org/debian/ buster-updates main contrib non-free
deb http://deb.debian.org/debian buster-backports main contrib non-free
Merci d'avance pour votre aide.
Dernière modification par BugsByte (17-04-2021 10:51:32)