logo Debian Debian Debian-France Debian-Facile Debian-fr.org Forum-Debian.fr Debian ? Communautés logo inclusivité

Debian-facile

Bienvenue sur Debian-Facile, site d'aide pour les nouveaux utilisateurs de Debian.

Vous n'êtes pas identifié(e).

#1 30-05-2020 20:13:38

Anonyme
Invité

Seagate Barracuda 1TO Neuf, des erreurs

Bonsoir,

je viens d'acheter aujourd'hui un disque dur SATA Seagate Barracuda 1TO neuf.

ça m'inquiète un peu. Je n'y comprend pas grand chose mais si je compare les résultats avec mes anciens disques, c'est inquiètant. ( Mes autres disques ne sont pas des Seagate )


Je donne les résultats  :

smartctl -s on -a /dev/sdb




=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 3.5
Device Model:     ST1000DM010-2EP102
Serial Number:    ZN1DE1QY
LU WWN Device Id: 5 000c50 0c4a87ace
Firmware Version: CC43
User Capacity:    1000204886016 bytes [1,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Sat May 30 21:05:45 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
          was never started.
          Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
          without error or no self-test has ever
          been run.
Total time to complete Offline
data collection:    (    0) seconds.
Offline data collection
capabilities:        (0x73) SMART execute Offline immediate.
          Auto Offline data collection on/off support.
          Suspend Offline collection upon new
          command.
          No Offline surface scan supported.
          Self-test supported.
          Conveyance Self-test supported.
          Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
          power-saving mode.
          Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
          General Purpose Logging supported.
Short self-test routine
recommended polling time:    (   1) minutes.
Extended self-test routine
recommended polling time:    ( 109) minutes.
Conveyance self-test routine
recommended polling time:    (   2) minutes.
SCT capabilities:          (0x1085) SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   082   069   006    Pre-fail  Always       -       178256222
  3 Spin_Up_Time            0x0003   099   099   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       3
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   100   253   045    Pre-fail  Always       -       200959
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       5
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       3
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0 0 0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   067   066   040    Old_age   Always       -       33 (Min/Max 32/33)
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       3
194 Temperature_Celsius     0x0022   033   026   000    Old_age   Always       -       33 (0 26 0 0 0)
195 Hardware_ECC_Recovered  0x001a   031   021   000    Old_age   Always       -       178256222
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       5h+01m+08.837s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       676153136
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       150015

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%         4         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 




1 Raw_Read_Error_Rate     0x000f   082   069   006    Pre-fail  Always       -       178256222
7 Seek_Error_Rate         0x000f   100   253   045    Pre-fail  Always       -       200959
195 Hardware_ECC_Recovered  0x001a   031   021   000    Old_age   Always       -       178256222
 



Pouvez-vous me remonter le moral ?

Dernière modification par Anonyme (31-05-2020 10:04:01)

#2 30-05-2020 20:22:02

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

J'ai trouvé ceci qui à tendance à me rassurer. Qu'en pensez vous ?

https://www.debian-fr.org/t/smartctl-qu … er/25928/4

Dernière modification par Anonyme (30-05-2020 20:26:07)

#3 30-05-2020 20:32:42

Debian Alain
Membre
Lieu : Bretagne
Distrib. : sid (unstable) / bullseye (stable)
Noyau : Linux sid 6.4.0-3-amd64
(G)UI : Gnome X.org (X11) / GDM3
Inscription : 11-03-2017
Site Web

Re : Seagate Barracuda 1TO Neuf, des erreurs

ceci aussi peut peut être t'aider dans tes recherches ...

roll

Hors ligne

#4 30-05-2020 21:20:22

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

Merci Debian Alain pour le lien wink

Sur un autre site, on dit que les valeurs ne sont pas inscrites, comment dire, à la même échelle.
https://www.ixsystems.com/community/thr … ate.68634/

Il faut appliquer "raw48:54" à ma commande smartctl pour l'ID 1 , 7 et 195. Je ne sais pas ce que ça vaut mais le résultat est le suivant :

sudo smartctl -a -v 1,raw48:54 /dev/sdb




ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   082   069   006    Pre-fail  Always       -       0
 



sudo smartctl -a -v 7,raw48:54 /dev/sdb



ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
 7 Seek_Error_Rate         0x000f   100   253   045    Pre-fail  Always       -       0
 



sudo smartctl -a -v 195,raw48:54 /dev/sdb




ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
195 Hardware_ECC_Recovered  0x001a   031   021   000    Old_age   Always       -       0
 



mais à une commande, on peut lui faire dire ce qu'on veux, si le résultat nous convient pas !!! tongue

Dernière modification par Anonyme (30-05-2020 21:23:08)

#5 30-05-2020 22:16:39

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

#6 31-05-2020 08:44:03

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

J'attend raleur avec impatience smile

#7 31-05-2020 14:24:24

raleur
Membre
Inscription : 03-10-2014

Re : Seagate Barracuda 1TO Neuf, des erreurs

Je n'ai pas grand-chose à dire. Les valeurs normalisées de ces attributs sont dans les clous et je ne sais pas interpréter leurs valeurs brutes. Il n'y a pas de secteurs réalloués ou défectueux.
La valeur normalisée de l'attribut 195 me semble quand même basse par rapport aux autres attributs.
Il y a aussi la pire valeur de l'attribut 7 qui est supérieure à la valeur normalisée, ce qui est anormal, mais là encore je ne sais pas l'interpréter.

Il vaut mieux montrer que raconter.

Hors ligne

#8 31-05-2020 14:38:43

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

Merci de m'avoir répondu smile

Quand tu parles de valeur normalisé de l'attribut 7, tu la vois où ?

#9 31-05-2020 14:52:41

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

En tout cas, ce qui me met en rogne, c'est quand on regarde ces infos en approchant la souris dessus et que ça nous dit :

Si non nulle ... problème, foutu, poubelle etc ... alors que c'est neuf.

Les constructeurs peuvent pas mettre des infos standards pour les non avertis sad

Dernière modification par Anonyme (31-05-2020 14:53:13)

#10 31-05-2020 15:04:08

raleur
Membre
Inscription : 03-10-2014

Re : Seagate Barracuda 1TO Neuf, des erreurs

Anonyme a écrit :

Quand tu parles de valeur normalisé de l'attribut 7, tu la vois où ?


Dans la colonne "VALUE".

Anonyme a écrit :

quand on regarde ces infos en approchant la souris dessus


Pardon ? Qu'est-ce que la souris vient faire ici ?


Il vaut mieux montrer que raconter.

Hors ligne

#11 31-05-2020 15:32:16

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

l'info bulles big_smile

Souris.png

Est-ce que je peux continuer mes transfers de fichiers sur ce disque en sachant que c'est pour un stockage qui sera ranger dans un placard. ( apparement oui )
De toute façon, je passerai chez LDLC avec les infos du SMART, voir ce qu'ils en disent. Je ferais un retour ici même.

Dernière modification par Anonyme (31-05-2020 15:38:20)

#12 02-06-2020 18:19:28

rodrigue7973
Membre
Lieu : beloeil
Distrib. : windows 11 pro
(G)UI : gnome
Inscription : 19-11-2017

Re : Seagate Barracuda 1TO Neuf, des erreurs

bonsoir,
ton disque dur 1To est defectueux!!! achète new 1 To smile
faut avant cloner  1To vers autre 1 To new
merci
Rodrigue7973

Etant dyslexique, j'ai des problèmes quant à la rédaction de messages en français courant. Je vous prie dès lors d'accepter toutes mes excuses si mes interventions peuvent vous paraître étranges et je vous remercie d'avance pour votre compréhension.

Hors ligne

#13 02-06-2020 19:07:32

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

Bonsoir rodrigue7973

Dis-moi pourquoi !!! big_smile

#14 02-06-2020 19:07:35

anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

Bonjour
si ça peu te rassurer (ou pas )  smile


smartctl -a /dev/sda
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.6.0-2-amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.12
Device Model:     ST3500413AS
Serial Number:    9VMYBZRE
LU WWN Device Id: 5 000c50 02db66d5a
Firmware Version: JC45
User Capacity:    500107862016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    7200 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Jun  2 19:57:00 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
          was completed without error.
          Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
          without error or no self-test has ever
          been run.
Total time to complete Offline
data collection:    (  600) seconds.
Offline data collection
capabilities:        (0x7b) SMART execute Offline immediate.
          Auto Offline data collection on/off support.
          Suspend Offline collection upon new
          command.
          Offline surface scan supported.
          Self-test supported.
          Conveyance Self-test supported.
          Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
          power-saving mode.
          Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
          General Purpose Logging supported.
Short self-test routine
recommended polling time:    (   1) minutes.
Extended self-test routine
recommended polling time:    (  84) minutes.
Conveyance self-test routine
recommended polling time:    (   2) minutes.
SCT capabilities:          (0x103f) SCT Status supported.
          SCT Error Recovery Control supported.
          SCT Feature Control supported.
          SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   119   099   006    Pre-fail  Always       -       221206589
  3 Spin_Up_Time            0x0003   100   100   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   099   099   020    Old_age   Always       -       1498
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   077   060   030    Pre-fail  Always       -       55816040
  9 Power_On_Hours          0x0032   082   082   000    Old_age   Always       -       16036
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   099   099   020    Old_age   Always       -       1056
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   099   000    Old_age   Always       -       2
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   065   051   045    Old_age   Always       -       35 (Min/Max 22/35)
194 Temperature_Celsius     0x0022   035   049   000    Old_age   Always       -       35 (0 17 0 0 0)
195 Hardware_ECC_Recovered  0x001a   023   022   000    Old_age   Always       -       221206589
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       19001 (169 17 0)
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       3504208377
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       2375290180

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
 



moi je prend maintenant plutôt du WD comme marque en disque mécanique ,
avec les ssd , rare que je prenne  un disque neuf traditionnel

tu peu regarder si  un firmware pour ce disque a mettre a jour
au vue de ce que je connais rien de mauvais comme te dis raleur
mais je saurai pas interpréter les valeurs  roll
ps: a part secteurs défectueux et ou réallouer ( Reallocated_Sector_Ct )

#15 02-06-2020 19:32:10

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

Bonsoir anonyme

Merci pour ton smartctl. Je l'avais déjà comparé avec le mien... ça m'a rassuré.

Fais moi un retour de cette commande sur ton seagate de l'ID 1 qui t'indique 221206589 avec cette commande :

smartctl -a -v 1,raw48:54 /dev/sda

Dernière modification par Anonyme (02-06-2020 19:33:03)

#16 02-06-2020 19:33:42

anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

voila  wink


smartctl -a -v 1,raw48:54 /dev/sda
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.6.0-2-amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.12
Device Model:     ST3500413AS
Serial Number:    9VMYBZRE
LU WWN Device Id: 5 000c50 02db66d5a
Firmware Version: JC45
User Capacity:    500107862016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    7200 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Jun  2 20:32:52 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
          was completed without error.
          Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
          without error or no self-test has ever
          been run.
Total time to complete Offline
data collection:    (  600) seconds.
Offline data collection
capabilities:        (0x7b) SMART execute Offline immediate.
          Auto Offline data collection on/off support.
          Suspend Offline collection upon new
          command.
          Offline surface scan supported.
          Self-test supported.
          Conveyance Self-test supported.
          Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
          power-saving mode.
          Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
          General Purpose Logging supported.
Short self-test routine
recommended polling time:    (   1) minutes.
Extended self-test routine
recommended polling time:    (  84) minutes.
Conveyance self-test routine
recommended polling time:    (   2) minutes.
SCT capabilities:          (0x103f) SCT Status supported.
          SCT Error Recovery Control supported.
          SCT Feature Control supported.
          SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   119   099   006    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0003   100   100   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   099   099   020    Old_age   Always       -       1498
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   077   060   030    Pre-fail  Always       -       55816100
  9 Power_On_Hours          0x0032   082   082   000    Old_age   Always       -       16036
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   099   099   020    Old_age   Always       -       1056
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   099   000    Old_age   Always       -       2
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   064   051   045    Old_age   Always       -       36 (Min/Max 22/36)
194 Temperature_Celsius     0x0022   036   049   000    Old_age   Always       -       36 (0 17 0 0 0)
195 Hardware_ECC_Recovered  0x001a   023   022   000    Old_age   Always       -       221206589
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       19001 (128 151 0)
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       3504208377
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       2375290180

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
 

#17 02-06-2020 19:33:53

Debian Alain
Membre
Lieu : Bretagne
Distrib. : sid (unstable) / bullseye (stable)
Noyau : Linux sid 6.4.0-3-amd64
(G)UI : Gnome X.org (X11) / GDM3
Inscription : 11-03-2017
Site Web

Re : Seagate Barracuda 1TO Neuf, des erreurs

exemple .

un disque défectueux :

regarde les deux lignes que j'ai mises en évidence .

sudo smartctl -a /dev/sdb


smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.6.14-amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST2000DM001-1CH164
Serial Number:    Z1E2XAN7
LU WWN Device Id: 5 000c50 04fbead7a
Firmware Version: CC24
User Capacity:    2000398934016 bytes [2,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Jun  2 20:17:02 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
          was completed without error.
          Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
          without error or no self-test has ever
          been run.
Total time to complete Offline
data collection:    (  592) seconds.
Offline data collection
capabilities:        (0x7b) SMART execute Offline immediate.
          Auto Offline data collection on/off support.
          Suspend Offline collection upon new
          command.
          Offline surface scan supported.
          Self-test supported.
          Conveyance Self-test supported.
          Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
          power-saving mode.
          Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
          General Purpose Logging supported.
Short self-test routine
recommended polling time:    (   1) minutes.
Extended self-test routine
recommended polling time:    ( 228) minutes.
Conveyance self-test routine
recommended polling time:    (   2) minutes.
SCT capabilities:          (0x3085) SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   117   092   006    Pre-fail  Always       -       144592416
  3 Spin_Up_Time            0x0003   096   095   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   095   095   020    Old_age   Always       -       5457
>>> 5 Reallocated_Sector_Ct   0x0033   097   097   010    Pre-fail  Always       -       3712 <<<
  7 Seek_Error_Rate         0x000f   078   060   030    Pre-fail  Always       -       4373236021
  9 Power_On_Hours          0x0032   078   078   000    Old_age   Always       -       19821
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   096   096   020    Old_age   Always       -       4116
>>> 183 Runtime_Bad_Block       0x0032   098   098   000    Old_age   Always       -       2 <<<
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   098   000    Old_age   Always       -       11 12 18
189 High_Fly_Writes         0x003a   091   091   000    Old_age   Always       -       9
190 Airflow_Temperature_Cel 0x0022   068   051   045    Old_age   Always       -       32 (Min/Max 24/33)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       1522
193 Load_Cycle_Count        0x0032   092   092   000    Old_age   Always       -       16530
194 Temperature_Celsius     0x0022   032   049   000    Old_age   Always       -       32 (0 13 0 0 0)
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       14569h+03m+30.256s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       33664298870
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       41298021062

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Interrupted (host reset)      90%     19491         -
# 2  Extended offline    Interrupted (host reset)      90%     19490         -
# 3  Short offline       Interrupted (host reset)      10%     19489         -
# 4  Short offline       Interrupted (host reset)      10%     19489         -
# 5  Short offline       Interrupted (host reset)      10%     19489         -
# 6  Short offline       Completed without error       00%     11340         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
 



ce disque fonctionne encore .

il est fatigué mais il fonctionne .

tu peux tester ton disque avec HDPARM :

mon disque défectueux (fonctionne beaucoup moins bien évidemment)
mais tu n'es pas encore là je pense .

sudo hdparm -t /dev/sdb


/dev/sdb:
 Timing buffered disk reads: 230 MB in  3.00 seconds =  76.63 MB/sec
 



un disque en bon état :

sudo hdparm -t /dev/sda


/dev/sda:
 Timing buffered disk reads: 474 MB in  3.01 seconds = 157.73 MB/sec
 



je parle bien de deux barracuda 3.5 pouces sata III (seagate , donc) .

voilà , si çà peut t'aider , Anonyme ...

tu me fais signe ? big_smile  big_smile  big_smile

NB:

manpage hdparm

https://doc.ubuntu-fr.org/hdparm

Dernière modification par Debian Alain (02-06-2020 19:52:40)

Hors ligne

#18 02-06-2020 19:39:40

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

@anonyme

1 Raw_Read_Error_Rate     0x000f   119   099   006    Pre-fail  Always       -       0



Zéro wink

@Debian Alain
Merci beaucoup, c'est moi qui rajeunit maintenant  big_smile

Dernière modification par Anonyme (02-06-2020 19:40:48)

#19 02-06-2020 20:00:36

Anonyme
Invité

Re : Seagate Barracuda 1TO Neuf, des erreurs

@Debian Alain

Mon Seagate Barracuda 1 To

hdparm -t /dev/sdb




/dev/sdb:
 Timing buffered disk reads: 584 MB in  3.00 seconds = 194.34 MB/sec
 



Correct ?

#20 02-06-2020 20:09:32

Debian Alain
Membre
Lieu : Bretagne
Distrib. : sid (unstable) / bullseye (stable)
Noyau : Linux sid 6.4.0-3-amd64
(G)UI : Gnome X.org (X11) / GDM3
Inscription : 11-03-2017
Site Web

Re : Seagate Barracuda 1TO Neuf, des erreurs

c'est ce que j'ai observé  sur mes disques .
donc je pense oui .

pour être tout à fait certain , demande confirmation à râleur .

Hors ligne

#21 13-09-2020 15:43:38

rodrigue7973
Membre
Lieu : beloeil
Distrib. : windows 11 pro
(G)UI : gnome
Inscription : 19-11-2017

Re : Seagate Barracuda 1TO Neuf, des erreurs

rodrigue@rodrigue-MS-7B16:~$ sudo hdparm -t /dev/sdb
[sudo] Mot de passe de rodrigue :         

/dev/sdb:
Timing buffered disk reads: 106 MB in  3.02 seconds =  35.05 MB/sec

Etant dyslexique, j'ai des problèmes quant à la rédaction de messages en français courant. Je vous prie dès lors d'accepter toutes mes excuses si mes interventions peuvent vous paraître étranges et je vous remercie d'avance pour votre compréhension.

Hors ligne

Pied de page des forums