les WD20EARX sont des vieux disques mis là en remplacement des seagate qui m'ont lâché .
Ils n'ont pas vocation à y rester eternellement .
j'ai sauvegardé mes données sur plusieurs supports .
mais si je peux garder celui là , ce sera bien .
j'envisage , MicP, de remplacer le ST2000 par un crucial 1To .
petit souci (mineur tu diras) je ne sais pas quel support prendre pour faire l'adaptation 2.5 pouces / 3.5 pouces .
https://www.ldlc.com/informatique/piece … rne/c4667/jusqu'ici , il fonctionne bien mais ses rapports smart sont pas rassurants .
sudo smartctl -a /dev/sdd
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.7.0-1-amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda Green (AF)
Device Model: ST2000DL003-9VT166
Serial Number: 6YD1QBLS
LU WWN Device Id: 5 000c50 0465b459f
Firmware Version: CC3C
User Capacity: 2000398934016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5900 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Jul 23 09:54:13 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 623) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 343) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x30b7) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 115 088 006 Pre-fail Always - 98520240
3 Spin_Up_Time 0x0003 093 090 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 096 096 020 Old_age Always - 4555
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 39646107145
9 Power_On_Hours 0x0032 033 033 000 Old_age Always - 59013
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 096 096 020 Old_age Always - 4550
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 836
188 Command_Timeout 0x0032 100 095 000 Old_age Always - 47245361783
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 067 050 045 Old_age Always - 33 (Min/Max 22/33)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1524
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 4555
194 Temperature_Celsius 0x0022 033 050 000 Old_age Always - 33 (0 17 0 0 0)
195 Hardware_ECC_Recovered 0x001a 033 003 000 Old_age Always - 98520240
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 10
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 59078 (250 202 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 901153515
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1114243956
SMART Error Log Version: 1
ATA Error Count: 834 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 834 occurred at disk power-on lifetime: 37677 hours (1569 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f8 87 9a 00 Error: UNC at LBA = 0x009a87f8 = 10127352
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 30 8a 9a 40 00 7d+11:40:04.319 READ FPDMA QUEUED
60 00 00 30 89 9a 40 00 7d+11:40:04.319 READ FPDMA QUEUED
60 00 00 30 88 9a 40 00 7d+11:40:04.318 READ FPDMA QUEUED
60 00 00 30 87 9a 40 00 7d+11:40:04.318 READ FPDMA QUEUED
60 00 00 30 86 9a 40 00 7d+11:40:04.318 READ FPDMA QUEUED
Error 833 occurred at disk power-on lifetime: 37677 hours (1569 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f8 87 9a 00 Error: UNC at LBA = 0x009a87f8 = 10127352
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 20 e0 87 9a 40 00 7d+11:40:00.728 READ FPDMA QUEUED
61 00 20 40 d0 a4 40 00 7d+11:40:00.727 WRITE FPDMA QUEUED
60 00 20 c0 87 9a 40 00 7d+11:40:00.727 READ FPDMA QUEUED
61 00 20 20 d0 a4 40 00 7d+11:40:00.727 WRITE FPDMA QUEUED
60 00 20 a0 87 9a 40 00 7d+11:40:00.727 READ FPDMA QUEUED
Error 832 occurred at disk power-on lifetime: 37655 hours (1568 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f8 87 9a 00 Error: UNC at LBA = 0x009a87f8 = 10127352
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 30 8a 9a 40 00 6d+14:09:31.194 READ FPDMA QUEUED
60 00 00 30 89 9a 40 00 6d+14:09:31.194 READ FPDMA QUEUED
60 00 00 30 88 9a 40 00 6d+14:09:31.194 READ FPDMA QUEUED
60 00 00 30 87 9a 40 00 6d+14:09:31.194 READ FPDMA QUEUED
60 00 00 30 86 9a 40 00 6d+14:09:31.194 READ FPDMA QUEUED
Error 831 occurred at disk power-on lifetime: 37655 hours (1568 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff 87 9a 00 Error: WP at LBA = 0x009a87ff = 10127359
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 08 c0 56 5d 40 00 6d+14:09:27.608 WRITE FPDMA QUEUED
60 00 01 ff 87 9a 40 00 6d+14:09:27.607 READ FPDMA QUEUED
61 00 90 60 51 5f 40 00 6d+14:09:27.606 WRITE FPDMA QUEUED
61 00 08 58 63 3b 40 00 6d+14:09:27.606 WRITE FPDMA QUEUED
61 00 28 ff ff ff 4f 00 6d+14:09:27.606 WRITE FPDMA QUEUED
Error 830 occurred at disk power-on lifetime: 37655 hours (1568 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 fe 87 9a 00 Error: UNC at LBA = 0x009a87fe = 10127358
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 40 b8 31 7b 43 00 6d+14:09:24.026 READ FPDMA QUEUED
61 00 10 40 56 5d 40 00 6d+14:09:24.026 WRITE FPDMA QUEUED
60 00 01 fe 87 9a 40 00 6d+14:09:24.026 READ FPDMA QUEUED
61 00 08 ff ff ff 4f 00 6d+14:09:24.025 WRITE FPDMA QUEUED
2f 00 01 10 00 00 20 00 6d+14:09:23.872 READ LOG EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed without error 00% 58375 -
# 2 Short offline Completed without error 00% 49888 -
# 3 Short offline Completed without error 00% 46327 -
# 4 Extended offline Aborted by host 90% 46327 -
# 5 Short offline Completed without error 00% 44252 -
# 6 Short offline Completed without error 00% 44246 -
# 7 Short offline Completed without error 00% 43303 -
# 8 Short offline Completed: read failure 10% 34897 10127352
# 9 Short offline Completed: read failure 10% 34823 10127352
#10 Short offline Completed: read failure 30% 34538 10127352
#11 Short offline Completed without error 00% 33775 -
#12 Short offline Completed without error 00% 33213 -
#13 Short offline Completed without error 00% 33081 -
#14 Short offline Completed without error 00% 32983 -
#15 Short offline Completed without error 00% 32912 -
#16 Short offline Completed without error 00% 32839 -
#17 Short offline Completed without error 00% 32774 -
#18 Short offline Completed without error 00% 9038 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
le ST4000 semble durer et ne présente pas de signes de faiblesse particuliers (enfin , apparemment)
sudo smartctl -a /dev/sdc
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.7.0-1-amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Video 3.5 HDD
Device Model: ST4000VM000-2AF166
Serial Number: WDH0AFF6
LU WWN Device Id: 5 000c50 09ca2e849
Firmware Version: SC11
User Capacity: 4000787030016 bytes [4,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5980 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Jul 23 09:56:21 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 591) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 637) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 082 064 044 Pre-fail Always - 161112719
3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 096 096 020 Old_age Always - 4552
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 084 060 045 Pre-fail Always - 280206189
9 Power_On_Hours 0x0032 079 079 000 Old_age Always - 18595 (222 131 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 097 097 020 Old_age Always - 4017
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 55835426834
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 072 056 040 Old_age Always - 28 (Min/Max 21/28)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1192
193 Load_Cycle_Count 0x0032 097 097 000 Old_age Always - 7938
194 Temperature_Celsius 0x0022 028 044 000 Old_age Always - 28 (0 15 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 15330 (163 28 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 24913438230
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 101308256698
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed without error 00% 17962 -
# 2 Extended offline Completed without error 00% 15413 -
# 3 Short offline Completed without error 00% 13710 -
# 4 Short offline Completed without error 00% 9496 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
le nvme est tout neuf .
sde et sdf (mme boitier usb tous deux. respectivement WD 3 To et WD 4 To ) sont neufs et reviennent du s.a.v. W.D.
ce sont , normalement , des red .
mon skyhawk (seagate que vous ne verrez pas de si tôt) m'a claqué dans les pattes au bout de six mois .
retour s.a.v. ldlc
Dernière modification par Debian Alain (23-07-2020 08:57:36)