logo Debian Debian Debian-France Debian-Facile Debian-fr.org Forum-Debian.fr Debian ? Communautés logo inclusivité

Debian-facile

Bienvenue sur Debian-Facile, site d'aide pour les nouveaux utilisateurs de Debian.

Vous n'êtes pas identifié(e).

#1 26-01-2020 18:14:20

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Disque dur qui ne se monte pas

Bonsoir à tous,
Depuis hier, un de mes disque dur me fait des misères, impossible de le monter :

sudo mount /dev/sdb1 /home/pitou/Modèles/
mount: mauvais type de système de fichiers, option erronée, superbloc erroné
        sur /dev/sdb1, page de code ou programme auxiliaire manquant, ou autre erreur

        Dans certains cas des renseignements utiles sont dans le journal
        système — essayez « dmesg | tail » ou quelque chose du genre.


Du coup, j'ai suivi le conseil et fait

 sudo dmesg | tail
[  179.675611] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  179.679610] ata3.00: configured for UDMA/133
[  179.679616] ata3.00: device reported invalid CHS sector 0
[  179.679625] ata3: EH complete
[  262.971617] sd 2:0:0:0: [sda] tag#30 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_TIMEOUT
[  262.971622] sd 2:0:0:0: [sda] tag#30 CDB: Read(10) 28 00 3a 38 5f 88 00 00 68 00
[  262.971625] blk_update_request: I/O error, dev sda, sector 976773000
[  307.291432] EXT4-fs (sdb1): unable to read superblock
[  307.291503] EXT4-fs (sdb1): unable to read superblock
[  307.291578] EXT4-fs (sdb1): unable to read superblock
 



C'est réparable ou direction poubelle ?

Oh, et si ça peut aider :

sudo fdisk -l
Disque /dev/sda : 465,8 GiB, 500107862016 octets, 976773168 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 4096 octets
taille d'E/S (minimale / optimale) : 4096 octets / 4096 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0x68fff889

Périphérique Amorçage Début       Fin  Secteurs Taille Id Type
/dev/sda1              2048 976773119 976771072 465,8G  7 HPFS/NTFS/exFAT


Disque /dev/sdb : 111,8 GiB, 120034123776 octets, 234441648 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0x2e86bbe5

Périphérique Amorçage Début       Fin  Secteurs Taille Id Type
/dev/sdb1    *         2046 234440703 234438658 111,8G  5 Étendue
/dev/sdb5              2048 234440703 234438656 111,8G 83 Linux


Disque /dev/sdc : 1,8 TiB, 2000398934016 octets, 3907029168 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 4096 octets
taille d'E/S (minimale / optimale) : 4096 octets / 4096 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0x00010eab

Périphérique Amorçage Début        Fin   Secteurs Taille Id Type
/dev/sdc1              2048 3907028991 3907026944   1,8T 83 Linux




Disque /dev/sdd : 465,8 GiB, 500107862016 octets, 976773168 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0x0002871c

Périphérique Amorçage Début       Fin  Secteurs Taille Id Type
/dev/sdd1                63 976768064 976768002 465,8G 83 Linux
 

Dernière modification par autrekrikri (26-01-2020 18:16:29)

Hors ligne

#2 26-01-2020 18:23:50

raleur
Membre
Inscription : 03-10-2014

Re : Disque dur qui ne se monte pas

D'après fdisk, sdb1 est une partition étendue. Ça ne se monte pas. Essaie plutôt sdb5.

Dernière modification par raleur (26-01-2020 18:26:00)


Il vaut mieux montrer que raconter.

Hors ligne

#3 26-01-2020 18:56:57

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

raleur a écrit :

D'après fdisk, sdb1 est une partition étendue. Ça ne se monte pas. Essaie plutôt sdb5.


Bonsoir,
alors, évidemment, j'ai débranché des disques ...
Bon, celui que je cherche fait 500Go.
C'est donc soit sda soit sdd.
Comme

 sudo mount /dev/sda1 /home/pitou/Modèles/

tourne dans le vide, ça doit être celui-ci ...
Du coup, je peux faire quoi ?

[edit]OK, alors, là, il y a un plus gros soucis, car je ne peux plus rien monter ...

Dernière modification par autrekrikri (26-01-2020 19:06:26)

Hors ligne

#4 26-01-2020 19:11:04

raleur
Membre
Inscription : 03-10-2014

Re : Disque dur qui ne se monte pas

Tu peux utiliser smartctl -a pour avoir un diagnostic d'un disque.

Il vaut mieux montrer que raconter.

Hors ligne

#5 26-01-2020 19:14:15

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

raleur a écrit :

Tu peux utiliser smartctl -a pour avoir un diagnostic d'un disque.


Je le lance avec quel dd ?
ici avec sdb :

pitou@bureau:~$ sudo smartctl -a /dev/sdb
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-11-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SandForce Driven SSDs
Device Model:     KINGSTON SV300S37A120G
Serial Number:    50026B7234063B39
LU WWN Device Id: 5 0026b7 234063b39
Firmware Version: 506ABBF0
User Capacity:    120 034 123 776 bytes [120 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS, ACS-2 T13/2015-D revision 3
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Sun Jan 26 19:15:07 2020 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (    0) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        (  48) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x0021) SCT Status supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   100   050    Pre-fail  Always       -       0/3232876
  5 Retired_Block_Count     0x0033   100   100   003    Pre-fail  Always       -       2
  9 Power_On_Hours_and_Msec 0x0032   040   040   000    Old_age   Always       -       53285h+04m+38.050s
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       224
171 Program_Fail_Count      0x0032   000   000   000    Old_age   Always       -       1
172 Erase_Fail_Count        0x0032   000   000   000    Old_age   Always       -       0
174 Unexpect_Power_Loss_Ct  0x0030   000   000   000    Old_age   Offline      -       76
177 Wear_Range_Delta        0x0000   000   000   000    Old_age   Offline      -       5
181 Program_Fail_Count      0x0032   000   000   000    Old_age   Always       -       1
182 Erase_Fail_Count        0x0032   000   000   000    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
189 Airflow_Temperature_Cel 0x0000   023   067   000    Old_age   Offline      -       23 (Min/Max 11/67)
194 Temperature_Celsius     0x0022   023   067   000    Old_age   Always       -       23 (Min/Max 11/67)
195 ECC_Uncorr_Error_Count  0x001c   120   120   000    Old_age   Offline      -       0/3232876
196 Reallocated_Event_Count 0x0033   100   100   003    Pre-fail  Always       -       2
201 Unc_Soft_Read_Err_Rate  0x001c   120   120   000    Old_age   Offline      -       0/3232876
204 Soft_ECC_Correct_Rate   0x001c   120   120   000    Old_age   Offline      -       0/3232876
230 Life_Curve_Status       0x0013   100   100   000    Pre-fail  Always       -       100
231 SSD_Life_Left           0x0013   100   100   010    Pre-fail  Always       -       0
233 SandForce_Internal      0x0000   000   000   000    Old_age   Offline      -       6593
234 SandForce_Internal      0x0032   000   000   000    Old_age   Always       -       4132
241 Lifetime_Writes_GiB     0x0032   000   000   000    Old_age   Always       -       4132
242 Lifetime_Reads_GiB      0x0032   000   000   000    Old_age   Always       -       1359

SMART Error Log not supported

SMART Self-test Log not supported

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 



et là avec sda :

pitou@bureau:~$ sudo smartctl -a /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-11-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba 3.5" DT01ACA... Desktop HDD
Device Model:     TOSHIBA DT01ACA050
Serial Number:    Y59VJKAKS
LU WWN Device Id: 5 000039 fe4da2750
Firmware Version: MS1OA750
User Capacity:    500 107 862 016 bytes [500 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is:    Sun Jan 26 19:16:55 2020 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
                                        was suspended by an interrupting command from host.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                ( 3765) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        (  63) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   047   047   016    Pre-fail  Always       -       928994454
  2 Throughput_Performance  0x0005   117   117   054    Pre-fail  Offline      -       163
  3 Spin_Up_Time            0x0007   126   126   024    Pre-fail  Always       -       181 (Average 183)
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -       119
  5 Reallocated_Sector_Ct   0x0033   001   001   005    Pre-fail  Always   FAILING_NOW 1520
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   113   113   020    Pre-fail  Offline      -       35
  9 Power_On_Hours          0x0012   096   096   000    Old_age   Always       -       32470
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       116
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       1158
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -       1158
194 Temperature_Celsius     0x0002   187   187   000    Old_age   Always       -       32 (Min/Max 12/42)
196 Reallocated_Event_Count 0x0032   001   001   000    Old_age   Always       -       2402
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 



Alors, dans mes souvenirs c'était le toshiba qui avait mes données.

Dernière modification par autrekrikri (26-01-2020 19:29:15)

Hors ligne

#6 26-01-2020 19:39:50

raleur
Membre
Inscription : 03-10-2014

Re : Disque dur qui ne se monte pas

  5 Reallocated_Sector_Ct   0x0033   001   001   005    Pre-fail  Always   FAILING_NOW 1520


Une chose est sûre : sda (Toshiba) est au bout du rouleau. Il a épuisé tout son stock de secteurs de réserve pour réallouer des secteurs défectueux. Il doit être remplacé au plus vite.
Néanmoins il ne semble pas avoir de secteurs illisibles actuellement (current pending et offline uncorrectable à 0).


Il vaut mieux montrer que raconter.

Hors ligne

#7 26-01-2020 19:44:16

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

raleur a écrit :

  5 Reallocated_Sector_Ct   0x0033   001   001   005    Pre-fail  Always   FAILING_NOW 1520


Une chose est sûre : sda (Toshiba) est au bout du rouleau. Il a épuisé tout son stock de secteurs de réserve pour réallouer des secteurs défectueux. Il doit être remplacé au plus vite.
Néanmoins il ne semble pas avoir de secteurs illisibles actuellement (current pending et offline uncorrectable à 0).


En effet, il n'est pas tout jeune, je vais en acheter un autre pour le remplacer. Mais j'aimerai récupérer mes données ... big_smile
Du coup, je ne vois pas quoi faire ...

Dernière modification par autrekrikri (26-01-2020 19:44:50)

Hors ligne

#8 26-01-2020 20:34:36

raleur
Membre
Inscription : 03-10-2014

Re : Disque dur qui ne se monte pas

D'après smartctl il reste lisible. Quel est le problème ? Montre des commandes, leurs retours, les logs du noyau...

Il vaut mieux montrer que raconter.

Hors ligne

#9 26-01-2020 20:39:16

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

raleur a écrit :

D'après smartctl il reste lisible. Quel est le problème ? Montre des commandes, leurs retours, les logs du noyau...


Comme dit dans un message plus haut :

Comme
 sudo mount /dev/sda1 /home/pitou/Modèles/

tourne dans le vide,


Lorsque je tape la commande, je valide, tape mon mdp et ... rien ne se passe, pas de retour rien, je ne peux même pas taper de nouvelle commande. Là, par exemple, ça fait plus de deux minutes que : rien lol ...
Par contre, les logs du noyau, je sais pas faire ... big_smile

Dernière modification par autrekrikri (26-01-2020 20:41:53)

Hors ligne

#10 26-01-2020 20:52:20

raleur
Membre
Inscription : 03-10-2014

Re : Disque dur qui ne se monte pas

autrekrikri a écrit :

Par contre, les logs du noyau, je sais pas faire


Ben si, avec dmesg comme dans ton premier post.


Il vaut mieux montrer que raconter.

Hors ligne

#11 26-01-2020 21:03:26

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

raleur a écrit :

autrekrikri a écrit :

Par contre, les logs du noyau, je sais pas faire


Ben si, avec dmesg comme dans ton premier post.


Ah, OK, je ne savais pas ce que c'était :-)

[ 3696.318592] ata3.00: device reported invalid CHS sector 0
[ 3696.318604] sd 2:0:0:0: [sda] tag#6 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 3696.318608] sd 2:0:0:0: [sda] tag#6 Sense Key : Illegal Request [current]
[ 3696.318611] sd 2:0:0:0: [sda] tag#6 Add. Sense: Unaligned write command
[ 3696.318616] sd 2:0:0:0: [sda] tag#6 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
[ 3696.318618] blk_update_request: I/O error, dev sda, sector 976772352
[ 3696.318646] ata3: EH complete
[ 4088.685781] systemd[1]: apt-daily.timer: Adding 27min 33.362517s random time.
[ 4088.685863] systemd[1]: anacron.timer: Adding 1min 41.007137s random time.
[ 4088.922422] systemd[1]: apt-daily.timer: Adding 11h 46min 56.311886s random time.
[ 4088.922502] systemd[1]: anacron.timer: Adding 1min 46.139424s random time.
[ 4088.970110] systemd[1]: apt-daily.timer: Adding 3h 57min 21.229603s random time.
[ 4088.970204] systemd[1]: anacron.timer: Adding 3.004989s random time.
[ 4089.016472] systemd[1]: apt-daily.timer: Adding 3h 5min 57.972645s random time.
[ 4089.016555] systemd[1]: anacron.timer: Adding 3min 19.350173s random time.
[ 4089.078593] systemd[1]: apt-daily.timer: Adding 3h 19min 40.129849s random time.
[ 4089.078674] systemd[1]: anacron.timer: Adding 2min 1.172419s random time.
[ 9313.632436] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9313.632440] ata3.00: failed command: READ DMA EXT
[ 9313.632445] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 8 dma 131072 in
                        res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9313.632447] ata3.00: status: { DRDY }
[ 9313.632449] ata3: hard resetting link
[ 9313.946722] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9313.950792] ata3.00: configured for UDMA/33
[ 9313.950802] ata3: EH complete
[ 9344.352251] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9344.352255] ata3.00: failed command: READ DMA EXT
[ 9344.352260] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 10 dma 131072 in
                        res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9344.352262] ata3.00: status: { DRDY }
[ 9344.352265] ata3: hard resetting link
[ 9344.666503] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9344.671968] ata3.00: configured for UDMA/33
[ 9344.671979] ata3: EH complete
[ 9377.120023] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9377.120028] ata3.00: failed command: READ DMA EXT
[ 9377.120032] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 27 dma 131072 in
                        res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9377.120034] ata3.00: status: { DRDY }
[ 9377.120037] ata3: hard resetting link
[ 9377.434248] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9377.438214] ata3.00: configured for UDMA/33
[ 9377.438224] ata3: EH complete
[ 9409.887873] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9409.887877] ata3.00: failed command: READ DMA EXT
[ 9409.887882] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 13 dma 131072 in
                        res 40/00:00:00:f4:2c/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9409.887883] ata3.00: status: { DRDY }
[ 9409.887886] ata3: hard resetting link
[ 9410.202054] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9410.205959] ata3.00: configured for UDMA/33
[ 9410.205973] ata3: EH complete
[ 9415.703283] perf: interrupt took too long (2515 > 2500), lowering kernel.perf_event_max_sample_rate to 79500
[ 9442.659508] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9442.659513] ata3.00: failed command: READ DMA EXT
[ 9442.659517] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 30 dma 131072 in
                        res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9442.659519] ata3.00: status: { DRDY }
[ 9442.659522] ata3: hard resetting link
[ 9442.973801] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9442.977947] ata3.00: configured for UDMA/33
[ 9442.977961] ata3: EH complete
[ 9473.375351] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9473.375358] ata3.00: failed command: READ DMA EXT
[ 9473.375367] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 16 dma 131072 in
                        res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9473.375371] ata3.00: status: { DRDY }
[ 9473.375376] ata3: hard resetting link
[ 9473.690116] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9473.695758] ata3.00: configured for UDMA/33
[ 9473.695775] sd 2:0:0:0: [sda] tag#16 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 9473.695779] sd 2:0:0:0: [sda] tag#16 Sense Key : Illegal Request [current]
[ 9473.695782] sd 2:0:0:0: [sda] tag#16 Add. Sense: Unaligned write command
[ 9473.695786] sd 2:0:0:0: [sda] tag#16 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
[ 9473.695789] blk_update_request: I/O error, dev sda, sector 976772352
[ 9473.695811] ata3: EH complete
 


je n'ai pas réussi à tout copier ... Désolé
En effet, ça parle de sda, mais je ne comprend rien ...

Dernière modification par autrekrikri (26-01-2020 21:04:33)

Hors ligne

#12 26-01-2020 21:12:13

raleur
Membre
Inscription : 03-10-2014

Re : Disque dur qui ne se monte pas

Je ne comprends pas tout non plus mais on dirait que le disque ne répond plus. Peut-être un arrêt et démarrage lui fera du bien ?

Il vaut mieux montrer que raconter.

Hors ligne

#13 26-01-2020 21:14:48

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

raleur a écrit :

Je ne comprends pas tout non plus mais on dirait que le disque ne répond plus. Peut-être un arrêt et démarrage lui fera du bien ?


Alors, déjà fait deux fois ... roll

Hors ligne

#14 26-01-2020 21:26:22

raleur
Membre
Inscription : 03-10-2014

Re : Disque dur qui ne se monte pas

Et fdisk et smartctl marchent encore avec ce disque ? Etonnant.

Il vaut mieux montrer que raconter.

Hors ligne

#15 26-01-2020 21:37:02

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

raleur a écrit :

Et fdisk et smartctl marchent encore avec ce disque ? Etonnant.


lol
Ah, du coup, c'est mourru mourru ?

Hors ligne

#16 26-01-2020 21:40:11

raleur
Membre
Inscription : 03-10-2014

Re : Disque dur qui ne se monte pas

Je n'ai pas dit ça. En ce moment, fdisk et smartctl marchent encore ou c'était avant ?

Dernière modification par raleur (26-01-2020 21:40:31)


Il vaut mieux montrer que raconter.

Hors ligne

#17 26-01-2020 21:48:39

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

raleur a écrit :

Je n'ai pas dit ça. En ce moment, fdisk et smartctl marchent encore ou c'était avant ?


Et bien fdisk me ressort :

Disque /dev/sda : 465,8 GiB, 500107862016 octets, 976773168 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 4096 octets
taille d'E/S (minimale / optimale) : 4096 octets / 4096 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0x68fff889

Périphérique Amorçage Début       Fin  Secteurs Taille Id Type
/dev/sda1              2048 976773119 976771072 465,8G  7 HPFS/NTFS/exFAT


Disque /dev/sdb : 111,8 GiB, 120034123776 octets, 234441648 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0x2e86bbe5

Périphérique Amorçage Début       Fin  Secteurs Taille Id Type
/dev/sdb1    *         2046 234440703 234438658 111,8G  5 Étendue
/dev/sdb5              2048 234440703 234438656 111,8G 83 Linux


Disque /dev/sdc : 1,8 TiB, 2000398934016 octets, 3907029168 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 4096 octets
taille d'E/S (minimale / optimale) : 4096 octets / 4096 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0x00010eab

Périphérique Amorçage Début        Fin   Secteurs Taille Id Type
/dev/sdc1              2048 3907028991 3907026944   1,8T 83 Linux




Disque /dev/sdd : 465,8 GiB, 500107862016 octets, 976773168 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0x0002871c

Périphérique Amorçage Début       Fin  Secteurs Taille Id Type
/dev/sdd1                63 976768064 976768002 465,8G 83 Linux
 


je dirai donc oui, de même pour smartctl

Hors ligne

#18 26-01-2020 22:08:39

Debian Alain
Membre
Lieu : Bretagne
Distrib. : sid (unstable) / bullseye (stable)
Noyau : Linux sid 6.4.0-3-amd64
(G)UI : Gnome X.org (X11) / GDM3
Inscription : 11-03-2017
Site Web

Re : Disque dur qui ne se monte pas

pour les logs , tu peux essayer ceci :

- pour dmesg :

dmesg | tail -n 100


dmesg | tail -n 100 | grep sda



- pour kern.log :

cat /var/log/kern.log | tail -n 100


cat /var/log/kern.log | tail -n 100 | grep sda



- pour syslog :

cat /var/log/syslog | tail -n 100


cat /var/log/syslog | tail -n 100 | grep sda



"tail -n 100" affiche les 100 dernières lignes
"grep sda" affiche les lignes contenant "sda"

Dernière modification par Debian Alain (26-01-2020 22:10:41)

Hors ligne

#19 26-01-2020 22:11:31

raleur
Membre
Inscription : 03-10-2014

Re : Disque dur qui ne se monte pas

Donc au moins une partie du disque est encore lisible, puisque fdisk parvient à lire les secteurs contenant la table de partition. Du coup j'essaierais de copier ce qui est lisible de la partition brute sda1 sur un autre disque (entier ou partition de taille suffisante) ou dans un fichier image avec ddrescue ou similaire (safecopy, recoverdm).

Il vaut mieux montrer que raconter.

Hors ligne

#20 26-01-2020 22:15:19

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

Debian Alain a écrit :

pour les logs , tu peux essayer ceci :

- pour dmesg :

dmesg | tail -n 100


[ 3632.826943] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3632.832542] ata3.00: configured for UDMA/33
[ 3632.832546] ata3.00: device reported invalid CHS sector 0
[ 3632.832552] ata3: EH complete
[ 3663.232432] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 3663.232436] ata3.00: failed command: READ DMA EXT
[ 3663.232440] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 20 dma 131072 in
                        res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3663.232442] ata3.00: status: { DRDY }
[ 3663.232445] ata3: hard resetting link
[ 3663.546699] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3663.552149] ata3.00: configured for UDMA/33
[ 3663.552153] ata3.00: device reported invalid CHS sector 0
[ 3663.552159] ata3: EH complete
[ 3696.000105] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 3696.000113] ata3.00: failed command: READ DMA EXT
[ 3696.000121] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 6 dma 131072 in
                        res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3696.000125] ata3.00: status: { DRDY }
[ 3696.000130] ata3: hard resetting link
[ 3696.314495] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3696.318586] ata3.00: configured for UDMA/33
[ 3696.318592] ata3.00: device reported invalid CHS sector 0
[ 3696.318604] sd 2:0:0:0: [sda] tag#6 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 3696.318608] sd 2:0:0:0: [sda] tag#6 Sense Key : Illegal Request [current]
[ 3696.318611] sd 2:0:0:0: [sda] tag#6 Add. Sense: Unaligned write command
[ 3696.318616] sd 2:0:0:0: [sda] tag#6 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
[ 3696.318618] blk_update_request: I/O error, dev sda, sector 976772352

[ 3696.318646] ata3: EH complete
[ 4088.685781] systemd[1]: apt-daily.timer: Adding 27min 33.362517s random time.
[ 4088.685863] systemd[1]: anacron.timer: Adding 1min 41.007137s random time.
[ 4088.922422] systemd[1]: apt-daily.timer: Adding 11h 46min 56.311886s random time.
[ 4088.922502] systemd[1]: anacron.timer: Adding 1min 46.139424s random time.
[ 4088.970110] systemd[1]: apt-daily.timer: Adding 3h 57min 21.229603s random time.
[ 4088.970204] systemd[1]: anacron.timer: Adding 3.004989s random time.
[ 4089.016472] systemd[1]: apt-daily.timer: Adding 3h 5min 57.972645s random time.
[ 4089.016555] systemd[1]: anacron.timer: Adding 3min 19.350173s random time.
[ 4089.078593] systemd[1]: apt-daily.timer: Adding 3h 19min 40.129849s random time.
[ 4089.078674] systemd[1]: anacron.timer: Adding 2min 1.172419s random time.
[ 9313.632436] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9313.632440] ata3.00: failed command: READ DMA EXT
[ 9313.632445] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 8 dma 131072 in
                        res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9313.632447] ata3.00: status: { DRDY }
[ 9313.632449] ata3: hard resetting link
[ 9313.946722] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9313.950792] ata3.00: configured for UDMA/33
[ 9313.950802] ata3: EH complete
[ 9344.352251] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9344.352255] ata3.00: failed command: READ DMA EXT
[ 9344.352260] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 10 dma 131072 in
                        res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9344.352262] ata3.00: status: { DRDY }
[ 9344.352265] ata3: hard resetting link
[ 9344.666503] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9344.671968] ata3.00: configured for UDMA/33
[ 9344.671979] ata3: EH complete
[ 9377.120023] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9377.120028] ata3.00: failed command: READ DMA EXT
[ 9377.120032] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 27 dma 131072 in
                        res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9377.120034] ata3.00: status: { DRDY }
[ 9377.120037] ata3: hard resetting link
[ 9377.434248] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9377.438214] ata3.00: configured for UDMA/33
[ 9377.438224] ata3: EH complete
[ 9409.887873] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9409.887877] ata3.00: failed command: READ DMA EXT
[ 9409.887882] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 13 dma 131072 in
                        res 40/00:00:00:f4:2c/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9409.887883] ata3.00: status: { DRDY }
[ 9409.887886] ata3: hard resetting link
[ 9410.202054] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9410.205959] ata3.00: configured for UDMA/33
[ 9410.205973] ata3: EH complete
[ 9415.703283] perf: interrupt took too long (2515 > 2500), lowering kernel.perf_event_max_sample_rate to 79500
[ 9442.659508] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9442.659513] ata3.00: failed command: READ DMA EXT
[ 9442.659517] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 30 dma 131072 in
                        res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9442.659519] ata3.00: status: { DRDY }
[ 9442.659522] ata3: hard resetting link
[ 9442.973801] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9442.977947] ata3.00: configured for UDMA/33
[ 9442.977961] ata3: EH complete
[ 9473.375351] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9473.375358] ata3.00: failed command: READ DMA EXT
[ 9473.375367] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 16 dma 131072 in
                        res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9473.375371] ata3.00: status: { DRDY }
[ 9473.375376] ata3: hard resetting link
[ 9473.690116] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9473.695758] ata3.00: configured for UDMA/33
[ 9473.695775] sd 2:0:0:0: [sda] tag#16 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 9473.695779] sd 2:0:0:0: [sda] tag#16 Sense Key : Illegal Request [current]
[ 9473.695782] sd 2:0:0:0: [sda] tag#16 Add. Sense: Unaligned write command
[ 9473.695786] sd 2:0:0:0: [sda] tag#16 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
[ 9473.695789] blk_update_request: I/O error, dev sda, sector 976772352
[ 9473.695811] ata3: EH complete
[13404.313712] perf: interrupt took too long (3191 > 3143), lowering kernel.perf_event_max_sample_rate to 62500
 


dmesg | tail -n 100 | grep sda


[ 3696.318604] sd 2:0:0:0: [sda] tag#6 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 3696.318608] sd 2:0:0:0: [sda] tag#6 Sense Key : Illegal Request [current]
[ 3696.318611] sd 2:0:0:0: [sda] tag#6 Add. Sense: Unaligned write command
[ 3696.318616] sd 2:0:0:0: [sda] tag#6 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
[ 3696.318618] blk_update_request: I/O error, dev sda, sector 976772352
[ 9473.695775] sd 2:0:0:0: [sda] tag#16 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 9473.695779] sd 2:0:0:0: [sda] tag#16 Sense Key : Illegal Request [current]
[ 9473.695782] sd 2:0:0:0: [sda] tag#16 Add. Sense: Unaligned write command
[ 9473.695786] sd 2:0:0:0: [sda] tag#16 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
[ 9473.695789] blk_update_request: I/O error, dev sda, sector 976772352
 



- pour kern.log :

cat /var/log/kern.log | tail -n 100



Jan 26 19:05:08 bureau kernel: [ 3602.111219] ata3.00: configured for UDMA/100
Jan 26 19:05:08 bureau kernel: [ 3602.111229] ata3.00: device reported invalid CHS sector 0
Jan 26 19:05:08 bureau kernel: [ 3602.111247] ata3: EH complete
Jan 26 19:05:39 bureau kernel: [ 3632.512732] ata3.00: limiting speed to UDMA/33:PIO4
Jan 26 19:05:39 bureau kernel: [ 3632.512735] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 19:05:39 bureau kernel: [ 3632.512740] ata3.00: failed command: READ DMA EXT
Jan 26 19:05:39 bureau kernel: [ 3632.512745] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 2 dma 131072 in
Jan 26 19:05:39 bureau kernel: [ 3632.512745]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 19:05:39 bureau kernel: [ 3632.512748] ata3.00: status: { DRDY }
Jan 26 19:05:39 bureau kernel: [ 3632.512751] ata3: hard resetting link
Jan 26 19:05:39 bureau kernel: [ 3632.826943] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 19:05:39 bureau kernel: [ 3632.832542] ata3.00: configured for UDMA/33
Jan 26 19:05:39 bureau kernel: [ 3632.832546] ata3.00: device reported invalid CHS sector 0
Jan 26 19:05:39 bureau kernel: [ 3632.832552] ata3: EH complete
Jan 26 19:06:09 bureau kernel: [ 3663.232432] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 19:06:09 bureau kernel: [ 3663.232436] ata3.00: failed command: READ DMA EXT
Jan 26 19:06:09 bureau kernel: [ 3663.232440] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 20 dma 131072 in
Jan 26 19:06:09 bureau kernel: [ 3663.232440]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 19:06:09 bureau kernel: [ 3663.232442] ata3.00: status: { DRDY }
Jan 26 19:06:09 bureau kernel: [ 3663.232445] ata3: hard resetting link
Jan 26 19:06:10 bureau kernel: [ 3663.546699] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 19:06:10 bureau kernel: [ 3663.552149] ata3.00: configured for UDMA/33
Jan 26 19:06:10 bureau kernel: [ 3663.552153] ata3.00: device reported invalid CHS sector 0
Jan 26 19:06:10 bureau kernel: [ 3663.552159] ata3: EH complete
Jan 26 19:06:42 bureau kernel: [ 3696.000105] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 19:06:42 bureau kernel: [ 3696.000113] ata3.00: failed command: READ DMA EXT
Jan 26 19:06:42 bureau kernel: [ 3696.000121] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 6 dma 131072 in
Jan 26 19:06:42 bureau kernel: [ 3696.000121]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)

Jan 26 19:06:42 bureau kernel: [ 3696.000125] ata3.00: status: { DRDY }
Jan 26 19:06:42 bureau kernel: [ 3696.000130] ata3: hard resetting link
Jan 26 19:06:43 bureau kernel: [ 3696.314495] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 19:06:43 bureau kernel: [ 3696.318586] ata3.00: configured for UDMA/33
Jan 26 19:06:43 bureau kernel: [ 3696.318592] ata3.00: device reported invalid CHS sector 0
Jan 26 19:06:43 bureau kernel: [ 3696.318604] sd 2:0:0:0: [sda] tag#6 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
Jan 26 19:06:43 bureau kernel: [ 3696.318608] sd 2:0:0:0: [sda] tag#6 Sense Key : Illegal Request [current]
Jan 26 19:06:43 bureau kernel: [ 3696.318611] sd 2:0:0:0: [sda] tag#6 Add. Sense: Unaligned write command
Jan 26 19:06:43 bureau kernel: [ 3696.318616] sd 2:0:0:0: [sda] tag#6 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
Jan 26 19:06:43 bureau kernel: [ 3696.318618] blk_update_request: I/O error, dev sda, sector 976772352
Jan 26 19:06:43 bureau kernel: [ 3696.318646] ata3: EH complete
Jan 26 20:40:20 bureau kernel: [ 9313.632436] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:40:20 bureau kernel: [ 9313.632440] ata3.00: failed command: READ DMA EXT
Jan 26 20:40:20 bureau kernel: [ 9313.632445] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 8 dma 131072 in
Jan 26 20:40:20 bureau kernel: [ 9313.632445]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:40:20 bureau kernel: [ 9313.632447] ata3.00: status: { DRDY }
Jan 26 20:40:20 bureau kernel: [ 9313.632449] ata3: hard resetting link
Jan 26 20:40:20 bureau kernel: [ 9313.946722] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:40:20 bureau kernel: [ 9313.950792] ata3.00: configured for UDMA/33
Jan 26 20:40:20 bureau kernel: [ 9313.950802] ata3: EH complete
Jan 26 20:40:51 bureau kernel: [ 9344.352251] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:40:51 bureau kernel: [ 9344.352255] ata3.00: failed command: READ DMA EXT
Jan 26 20:40:51 bureau kernel: [ 9344.352260] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 10 dma 131072 in
Jan 26 20:40:51 bureau kernel: [ 9344.352260]          res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:40:51 bureau kernel: [ 9344.352262] ata3.00: status: { DRDY }
Jan 26 20:40:51 bureau kernel: [ 9344.352265] ata3: hard resetting link
Jan 26 20:40:51 bureau kernel: [ 9344.666503] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:40:51 bureau kernel: [ 9344.671968] ata3.00: configured for UDMA/33
Jan 26 20:40:51 bureau kernel: [ 9344.671979] ata3: EH complete
Jan 26 20:41:23 bureau kernel: [ 9377.120023] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:41:23 bureau kernel: [ 9377.120028] ata3.00: failed command: READ DMA EXT
Jan 26 20:41:23 bureau kernel: [ 9377.120032] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 27 dma 131072 in
Jan 26 20:41:23 bureau kernel: [ 9377.120032]          res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:41:23 bureau kernel: [ 9377.120034] ata3.00: status: { DRDY }
Jan 26 20:41:23 bureau kernel: [ 9377.120037] ata3: hard resetting link
Jan 26 20:41:24 bureau kernel: [ 9377.434248] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:41:24 bureau kernel: [ 9377.438214] ata3.00: configured for UDMA/33
Jan 26 20:41:24 bureau kernel: [ 9377.438224] ata3: EH complete
Jan 26 20:41:56 bureau kernel: [ 9409.887873] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:41:56 bureau kernel: [ 9409.887877] ata3.00: failed command: READ DMA EXT
Jan 26 20:41:56 bureau kernel: [ 9409.887882] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 13 dma 131072 in
Jan 26 20:41:56 bureau kernel: [ 9409.887882]          res 40/00:00:00:f4:2c/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:41:56 bureau kernel: [ 9409.887883] ata3.00: status: { DRDY }
Jan 26 20:41:56 bureau kernel: [ 9409.887886] ata3: hard resetting link
Jan 26 20:41:56 bureau kernel: [ 9410.202054] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:41:56 bureau kernel: [ 9410.205959] ata3.00: configured for UDMA/33
Jan 26 20:41:56 bureau kernel: [ 9410.205973] ata3: EH complete
Jan 26 20:42:02 bureau kernel: [ 9415.703283] perf: interrupt took too long (2515 > 2500), lowering kernel.perf_event_max_sample_rate to 79500
Jan 26 20:42:29 bureau kernel: [ 9442.659508] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:42:29 bureau kernel: [ 9442.659513] ata3.00: failed command: READ DMA EXT
Jan 26 20:42:29 bureau kernel: [ 9442.659517] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 30 dma 131072 in
Jan 26 20:42:29 bureau kernel: [ 9442.659517]          res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:42:29 bureau kernel: [ 9442.659519] ata3.00: status: { DRDY }
Jan 26 20:42:29 bureau kernel: [ 9442.659522] ata3: hard resetting link
Jan 26 20:42:29 bureau kernel: [ 9442.973801] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:42:29 bureau kernel: [ 9442.977947] ata3.00: configured for UDMA/33
Jan 26 20:42:29 bureau kernel: [ 9442.977961] ata3: EH complete
Jan 26 20:43:00 bureau kernel: [ 9473.375351] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:43:00 bureau kernel: [ 9473.375358] ata3.00: failed command: READ DMA EXT
Jan 26 20:43:00 bureau kernel: [ 9473.375367] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 16 dma 131072 in
Jan 26 20:43:00 bureau kernel: [ 9473.375367]          res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:43:00 bureau kernel: [ 9473.375371] ata3.00: status: { DRDY }
Jan 26 20:43:00 bureau kernel: [ 9473.375376] ata3: hard resetting link
Jan 26 20:43:00 bureau kernel: [ 9473.690116] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:43:00 bureau kernel: [ 9473.695758] ata3.00: configured for UDMA/33
Jan 26 20:43:00 bureau kernel: [ 9473.695775] sd 2:0:0:0: [sda] tag#16 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
Jan 26 20:43:00 bureau kernel: [ 9473.695779] sd 2:0:0:0: [sda] tag#16 Sense Key : Illegal Request [current]
Jan 26 20:43:00 bureau kernel: [ 9473.695782] sd 2:0:0:0: [sda] tag#16 Add. Sense: Unaligned write command
Jan 26 20:43:00 bureau kernel: [ 9473.695786] sd 2:0:0:0: [sda] tag#16 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
Jan 26 20:43:00 bureau kernel: [ 9473.695789] blk_update_request: I/O error, dev sda, sector 976772352
Jan 26 20:43:00 bureau kernel: [ 9473.695811] ata3: EH complete
Jan 26 21:48:31 bureau kernel: [13404.313712] perf: interrupt took too long (3191 > 3143), lowering kernel.perf_event_max_sample_rate to 62500
 


cat /var/log/kern.log | tail -n 100 | grep sda


Jan 26 19:06:43 bureau kernel: [ 3696.318604] sd 2:0:0:0: [sda] tag#6 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
Jan 26 19:06:43 bureau kernel: [ 3696.318608] sd 2:0:0:0: [sda] tag#6 Sense Key : Illegal Request [current]
Jan 26 19:06:43 bureau kernel: [ 3696.318611] sd 2:0:0:0: [sda] tag#6 Add. Sense: Unaligned write command
Jan 26 19:06:43 bureau kernel: [ 3696.318616] sd 2:0:0:0: [sda] tag#6 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
Jan 26 19:06:43 bureau kernel: [ 3696.318618] blk_update_request: I/O error, dev sda, sector 976772352
Jan 26 20:43:00 bureau kernel: [ 9473.695775] sd 2:0:0:0: [sda] tag#16 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
Jan 26 20:43:00 bureau kernel: [ 9473.695779] sd 2:0:0:0: [sda] tag#16 Sense Key : Illegal Request [current]
Jan 26 20:43:00 bureau kernel: [ 9473.695782] sd 2:0:0:0: [sda] tag#16 Add. Sense: Unaligned write command
Jan 26 20:43:00 bureau kernel: [ 9473.695786] sd 2:0:0:0: [sda] tag#16 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
Jan 26 20:43:00 bureau kernel: [ 9473.695789] blk_update_request: I/O error, dev sda, sector 976772352
 



- pour syslog :

cat /var/log/syslog | tail -n 100



Jan 26 20:13:21 bureau smartd[1661]: Device: /dev/sda [SAT], Failed SMART usage Attribute: 5 Reallocated_Sector_Ct.
Jan 26 20:17:01 bureau CRON[31825]: (root) CMD (   cd / && run-parts --report /etc/cron.hourly)
Jan 26 20:40:20 bureau kernel: [ 9313.632436] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:40:20 bureau kernel: [ 9313.632440] ata3.00: failed command: READ DMA EXT
Jan 26 20:40:20 bureau kernel: [ 9313.632445] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 8 dma 131072 in
Jan 26 20:40:20 bureau kernel: [ 9313.632445]          res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:40:20 bureau kernel: [ 9313.632447] ata3.00: status: { DRDY }
Jan 26 20:40:20 bureau kernel: [ 9313.632449] ata3: hard resetting link
Jan 26 20:40:20 bureau kernel: [ 9313.946722] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:40:20 bureau kernel: [ 9313.950792] ata3.00: configured for UDMA/33
Jan 26 20:40:20 bureau kernel: [ 9313.950802] ata3: EH complete
Jan 26 20:40:51 bureau kernel: [ 9344.352251] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:40:51 bureau kernel: [ 9344.352255] ata3.00: failed command: READ DMA EXT
Jan 26 20:40:51 bureau kernel: [ 9344.352260] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 10 dma 131072 in
Jan 26 20:40:51 bureau kernel: [ 9344.352260]          res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:40:51 bureau kernel: [ 9344.352262] ata3.00: status: { DRDY }
Jan 26 20:40:51 bureau kernel: [ 9344.352265] ata3: hard resetting link
Jan 26 20:40:51 bureau kernel: [ 9344.666503] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:40:51 bureau kernel: [ 9344.671968] ata3.00: configured for UDMA/33
Jan 26 20:40:51 bureau kernel: [ 9344.671979] ata3: EH complete
Jan 26 20:41:23 bureau kernel: [ 9377.120023] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:41:23 bureau kernel: [ 9377.120028] ata3.00: failed command: READ DMA EXT
Jan 26 20:41:23 bureau kernel: [ 9377.120032] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 27 dma 131072 in
Jan 26 20:41:23 bureau kernel: [ 9377.120032]          res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)

Jan 26 20:41:23 bureau kernel: [ 9377.120034] ata3.00: status: { DRDY }
Jan 26 20:41:23 bureau kernel: [ 9377.120037] ata3: hard resetting link
Jan 26 20:41:24 bureau kernel: [ 9377.434248] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:41:24 bureau kernel: [ 9377.438214] ata3.00: configured for UDMA/33
Jan 26 20:41:24 bureau kernel: [ 9377.438224] ata3: EH complete
Jan 26 20:41:56 bureau kernel: [ 9409.887873] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:41:56 bureau kernel: [ 9409.887877] ata3.00: failed command: READ DMA EXT
Jan 26 20:41:56 bureau kernel: [ 9409.887882] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 13 dma 131072 in
Jan 26 20:41:56 bureau kernel: [ 9409.887882]          res 40/00:00:00:f4:2c/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:41:56 bureau kernel: [ 9409.887883] ata3.00: status: { DRDY }
Jan 26 20:41:56 bureau kernel: [ 9409.887886] ata3: hard resetting link
Jan 26 20:41:56 bureau kernel: [ 9410.202054] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:41:56 bureau kernel: [ 9410.205959] ata3.00: configured for UDMA/33
Jan 26 20:41:56 bureau kernel: [ 9410.205973] ata3: EH complete
Jan 26 20:42:02 bureau kernel: [ 9415.703283] perf: interrupt took too long (2515 > 2500), lowering kernel.perf_event_max_sample_rate to 79500
Jan 26 20:42:29 bureau kernel: [ 9442.659508] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:42:29 bureau kernel: [ 9442.659513] ata3.00: failed command: READ DMA EXT
Jan 26 20:42:29 bureau kernel: [ 9442.659517] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 30 dma 131072 in
Jan 26 20:42:29 bureau kernel: [ 9442.659517]          res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:42:29 bureau kernel: [ 9442.659519] ata3.00: status: { DRDY }
Jan 26 20:42:29 bureau kernel: [ 9442.659522] ata3: hard resetting link
Jan 26 20:42:29 bureau kernel: [ 9442.973801] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:42:29 bureau kernel: [ 9442.977947] ata3.00: configured for UDMA/33
Jan 26 20:42:29 bureau kernel: [ 9442.977961] ata3: EH complete
Jan 26 20:43:00 bureau kernel: [ 9473.375351] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Jan 26 20:43:00 bureau kernel: [ 9473.375358] ata3.00: failed command: READ DMA EXT
Jan 26 20:43:00 bureau kernel: [ 9473.375367] ata3.00: cmd 25/00:00:00:5d:38/00:01:3a:00:00/e0 tag 16 dma 131072 in
Jan 26 20:43:00 bureau kernel: [ 9473.375367]          res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Jan 26 20:43:00 bureau kernel: [ 9473.375371] ata3.00: status: { DRDY }
Jan 26 20:43:00 bureau kernel: [ 9473.375376] ata3: hard resetting link
Jan 26 20:43:00 bureau kernel: [ 9473.690116] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jan 26 20:43:00 bureau kernel: [ 9473.695758] ata3.00: configured for UDMA/33
Jan 26 20:43:00 bureau kernel: [ 9473.695775] sd 2:0:0:0: [sda] tag#16 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
Jan 26 20:43:00 bureau kernel: [ 9473.695779] sd 2:0:0:0: [sda] tag#16 Sense Key : Illegal Request [current]
Jan 26 20:43:00 bureau kernel: [ 9473.695782] sd 2:0:0:0: [sda] tag#16 Add. Sense: Unaligned write command
Jan 26 20:43:00 bureau kernel: [ 9473.695786] sd 2:0:0:0: [sda] tag#16 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
Jan 26 20:43:00 bureau kernel: [ 9473.695789] blk_update_request: I/O error, dev sda, sector 976772352
Jan 26 20:43:00 bureau kernel: [ 9473.695811] ata3: EH complete
Jan 26 20:43:21 bureau smartd[1661]: Device: /dev/sda [SAT], FAILED SMART self-check. BACK UP DATA NOW!
Jan 26 20:43:21 bureau smartd[1661]: Device: /dev/sda [SAT], Failed SMART usage Attribute: 5 Reallocated_Sector_Ct.
Jan 26 20:43:21 bureau smartd[1661]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 176 to 181
Jan 26 21:04:36 bureau systemd[1]: Started Run anacron jobs.
Jan 26 21:04:36 bureau anacron[21843]: Anacron 2.3 started on 2020-01-26
Jan 26 21:04:36 bureau anacron[21843]: Normal exit (0 jobs run)
Jan 26 21:04:36 bureau systemd[1]: anacron.timer: Adding 46.220472s random time.
Jan 26 21:12:50 bureau freshclam[549]: Sun Jan 26 21:12:50 2020 -> Received signal: wake up
Jan 26 21:12:50 bureau freshclam[549]: Sun Jan 26 21:12:50 2020 -> ClamAV update process started at Sun Jan 26 21:12:50 2020
Jan 26 21:12:50 bureau freshclam[549]: Sun Jan 26 21:12:50 2020 -> ^Your ClamAV installation is OUTDATED!
Jan 26 21:12:50 bureau freshclam[549]: Sun Jan 26 21:12:50 2020 -> ^Local version: 0.101.4 Recommended version: 0.102.1
Jan 26 21:12:50 bureau freshclam[549]: Sun Jan 26 21:12:50 2020 -> DON'T PANIC! Read https://www.clamav.net/documents/upgrading-clamav
Jan 26 21:12:50 bureau freshclam[549]: Sun Jan 26 21:12:50 2020 -> main.cld is up to date (version: 59, sigs: 4564902, f-level: 60, builder: sigmgr)
Jan 26 21:12:50 bureau freshclam[549]: Sun Jan 26 21:12:50 2020 -> daily.cld is up to date (version: 25707, sigs: 2162077, f-level: 63, builder: raynman)
Jan 26 21:12:50 bureau freshclam[549]: Sun Jan 26 21:12:50 2020 -> bytecode.cvd is up to date (version: 331, sigs: 94, f-level: 63, builder: anvilleg)
Jan 26 21:13:21 bureau smartd[1661]: Device: /dev/sda [SAT], FAILED SMART self-check. BACK UP DATA NOW!
Jan 26 21:13:21 bureau smartd[1661]: Device: /dev/sda [SAT], Failed SMART usage Attribute: 5 Reallocated_Sector_Ct.
Jan 26 21:13:21 bureau smartd[1661]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 181 to 176
Jan 26 21:17:01 bureau CRON[27843]: (root) CMD (   cd / && run-parts --report /etc/cron.hourly)
Jan 26 21:43:21 bureau smartd[1661]: Device: /dev/sda [SAT], FAILED SMART self-check. BACK UP DATA NOW!
Jan 26 21:43:21 bureau smartd[1661]: Device: /dev/sda [SAT], Failed SMART usage Attribute: 5 Reallocated_Sector_Ct.
Jan 26 21:43:21 bureau smartd[1661]: Device: /dev/sdb [SAT], SMART Usage Attribute: 189 Airflow_Temperature_Cel changed from 23 to 24
Jan 26 21:43:21 bureau smartd[1661]: Device: /dev/sdb [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 23 to 24
Jan 26 21:48:31 bureau kernel: [13404.313712] perf: interrupt took too long (3191 > 3143), lowering kernel.perf_event_max_sample_rate to 62500
Jan 26 22:01:36 bureau systemd[1]: Started Run anacron jobs.
Jan 26 22:01:36 bureau anacron[16315]: Anacron 2.3 started on 2020-01-26
Jan 26 22:01:36 bureau anacron[16315]: Normal exit (0 jobs run)
Jan 26 22:01:36 bureau systemd[1]: anacron.timer: Adding 1min 35.738404s random time.
Jan 26 22:12:50 bureau freshclam[549]: Sun Jan 26 22:12:50 2020 -> Received signal: wake up
Jan 26 22:12:50 bureau freshclam[549]: Sun Jan 26 22:12:50 2020 -> ClamAV update process started at Sun Jan 26 22:12:50 2020
Jan 26 22:12:50 bureau freshclam[549]: Sun Jan 26 22:12:50 2020 -> ^Your ClamAV installation is OUTDATED!
Jan 26 22:12:50 bureau freshclam[549]: Sun Jan 26 22:12:50 2020 -> ^Local version: 0.101.4 Recommended version: 0.102.1
Jan 26 22:12:50 bureau freshclam[549]: Sun Jan 26 22:12:50 2020 -> DON'T PANIC! Read https://www.clamav.net/documents/upgrading-clamav
Jan 26 22:12:50 bureau freshclam[549]: Sun Jan 26 22:12:50 2020 -> main.cld is up to date (version: 59, sigs: 4564902, f-level: 60, builder: sigmgr)
Jan 26 22:12:50 bureau freshclam[549]: Sun Jan 26 22:12:50 2020 -> daily.cld is up to date (version: 25707, sigs: 2162077, f-level: 63, builder: raynman)
Jan 26 22:12:50 bureau freshclam[549]: Sun Jan 26 22:12:50 2020 -> bytecode.cvd is up to date (version: 331, sigs: 94, f-level: 63, builder: anvilleg)
Jan 26 22:13:20 bureau smartd[1661]: Device: /dev/sda [SAT], FAILED SMART self-check. BACK UP DATA NOW!
Jan 26 22:13:20 bureau smartd[1661]: Device: /dev/sda [SAT], Failed SMART usage Attribute: 5 Reallocated_Sector_Ct.
 


cat /var/log/syslog | tail -n 100 | grep sda


Jan 26 20:13:21 bureau smartd[1661]: Device: /dev/sda [SAT], Failed SMART usage Attribute: 5 Reallocated_Sector_Ct.
Jan 26 20:43:00 bureau kernel: [ 9473.695775] sd 2:0:0:0: [sda] tag#16 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
Jan 26 20:43:00 bureau kernel: [ 9473.695779] sd 2:0:0:0: [sda] tag#16 Sense Key : Illegal Request [current]
Jan 26 20:43:00 bureau kernel: [ 9473.695782] sd 2:0:0:0: [sda] tag#16 Add. Sense: Unaligned write command
Jan 26 20:43:00 bureau kernel: [ 9473.695786] sd 2:0:0:0: [sda] tag#16 CDB: Read(10) 28 00 3a 38 5d 00 00 01 00 00
Jan 26 20:43:00 bureau kernel: [ 9473.695789] blk_update_request: I/O error, dev sda, sector 976772352
Jan 26 20:43:21 bureau smartd[1661]: Device: /dev/sda [SAT], FAILED SMART self-check. BACK UP DATA NOW!
Jan 26 20:43:21 bureau smartd[1661]: Device: /dev/sda [SAT], Failed SMART usage Attribute: 5 Reallocated_Sector_Ct.
Jan 26 20:43:21 bureau smartd[1661]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 176 to 181
Jan 26 21:13:21 bureau smartd[1661]: Device: /dev/sda [SAT], FAILED SMART self-check. BACK UP DATA NOW!
Jan 26 21:13:21 bureau smartd[1661]: Device: /dev/sda [SAT], Failed SMART usage Attribute: 5 Reallocated_Sector_Ct.
Jan 26 21:13:21 bureau smartd[1661]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 181 to 176
Jan 26 21:43:21 bureau smartd[1661]: Device: /dev/sda [SAT], FAILED SMART self-check. BACK UP DATA NOW!
Jan 26 21:43:21 bureau smartd[1661]: Device: /dev/sda [SAT], Failed SMART usage Attribute: 5 Reallocated_Sector_Ct.
Jan 26 22:13:20 bureau smartd[1661]: Device: /dev/sda [SAT], FAILED SMART self-check. BACK UP DATA NOW!
Jan 26 22:13:20 bureau smartd[1661]: Device: /dev/sda [SAT], Failed SMART usage Attribute: 5 Reallocated_Sector_Ct.
 

Hors ligne

#21 26-01-2020 22:17:50

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

Désolé, mais pour ce soir, je vais me coucher, levé très tôt demain ...
En tout cas, merci pour tout ce que tu as déjà fais "raleur". À demain. ops.gif

Hors ligne

#22 26-01-2020 22:29:05

Debian Alain
Membre
Lieu : Bretagne
Distrib. : sid (unstable) / bullseye (stable)
Noyau : Linux sid 6.4.0-3-amd64
(G)UI : Gnome X.org (X11) / GDM3
Inscription : 11-03-2017
Site Web

Re : Disque dur qui ne se monte pas

pour faire court , procure toi un disque neuf (ou récent)

-- par exemple -- ainsi que une copie de -- clonezilla -- 

-- éventuellement -- si besoin .

Hors ligne

#23 28-01-2020 09:54:13

autrekrikri
Membre
Distrib. : Debian 9
Noyau : Linux 4.9.0-8-amd64
(G)UI : wmii
Inscription : 26-01-2016

Re : Disque dur qui ne se monte pas

Bonjour à tous,
Alors, après une journée un peu longue, j'ai réfléchi, j'ai donc débranché mon disque dur puis rallumé mon PC : le disque Toshiba fout le bazar en effet, sans lui mon PC focntionne parfaitement.
J'ai trouvé un autre disque dur dans mon placard et l'ai mis à sa place, ça roule et c'est déjà ça.
@Debian Alain : clonezilla m'est totalement inconnu, il va falloir que je trouve un tuto big_smile

Hors ligne

Pied de page des forums